Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Michał Borecki has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of the Implementation of Effective Grounding in 400 kV Overhead Lines

    by Michał Borecki, Paweł Kluge, Maciej Ciuba

    Grounding is one of the key elements ensuring the reliable operation of overhead lines. The purpose of this paper is to provide a comprehensive assessment of grounding using a 400 kV overhead line as an example. The paper presents the results of diagnostic grounding measurements of various types of 400 kV overhead line poles, performed according to technical documentation and taking into account local terrain characteristics. The paper examines a large number of overhead line poles in both uniform and varied terrains, taking into account soil conditions based on geotechnical documentation. Furthermore, the paper presents a simulation analysis of lightning current dissipation through the grounding of a selected pole, taking into account geotechnical soil investigations with respect to soil stratification. The final section of the paper includes guidelines on grounding and assessment of the technical condition of grounding systems, which may be useful to transmission and distribution network operators.

  • Open Access

    Variety of attenuation of RF suppression filters

    by Michał Borecki, Jan Sroka

  • Open Access

    Influence of Spark Gap Parameters on the Strength of the Surge Protection Device and the Method of Its Selection

    by Michał Borecki

    The paper aims to analyze the factors affecting the parameters of surge protection devices with a spark gap and assess the impact of changing these parameters on the level of overhead line strength. For this purpose, this paper contains the results of tests that show the assessment of the impact of changing the spark gap parameters on the voltage–time characteristics of selected protection devices in the range of negative and positive polarity. The paper presents how the change in the parameters of the component element of the surge protection device, which is the spark gap, may affect the selection of the line surge protection method. In addition, the paper presents a method of assessing the strength of an overhead line, taking into account the case of installing surge protection devices at the insulators. The implementation of these tests supports further activities aimed at the actual values of parameters affecting the strength of overhead lines.


  • Open Access

    Diversity Pertaining to the Attenuation of the RF Disturbance Suppression Power Line Filters

    by Michał Borecki, Jan Sroka

    Filters for the suppression of the RF disturbances in power lines are passive; wideband stop filters attenuating common as well as differential disturbances should be insensitive to the variation in the impedance at the input and the output. The design and verification process of such filters differs entirely from that used for the signal RF filters. In the document CISPR 17, entitled “Methods of measurement of the suppression characteristics of passive EMC filtering devices”, two definitions of the attenuation of the common and differential modes are presented. The first is simply direct measurement, and the second is based on a calculation using the single-ended S-parameters of the multiport. These two definitions are the source of diversity. In this paper, we hypothesize that the attenuations achieved with these two methods are identical only if the filter is in perfect balance. Consequently, different attenuations can be achieved. The requirement of balance can be violated due to the tolerances of the components used in the filter. The paper begins with a simple unbalanced four-port, for which analytical formulas are derived. It is also shown that an approach with single-ended S-parameters enables the calculation of the mode conversion between the input and the output, which is called the conversion loss. This is the measure of the grade of the imbalance. Thereafter, the common-mode attenuation of an exemplary RF suppression filter is derived with the presented methods. Additionally, the conversion loss of the filter is calculated. The comparison of the conversion loss with both attenuations is satisfactory, proving the hypothesis formulated in the paper.


  • Open Access

    Testing of Selected Surge Protection Devices in the Context of the Possibility of Ensuring the Reliability of Power Grids

    by Michał Borecki, Maciej Ciuba

    The paper aims to analyze the parameters of prototypes of new overvoltage protection devices for power grids—a multi-chamber insulator arrester (MCA) and a long flashover arrester (LFA). The article presents the research results on determining the actual MCA and LFA impact characteristics. Moreover, the results were compared to assess the effectiveness of the overvoltage protection devices. The research results presented in this article will supplement missing information about the devices. They will make it possible to evaluate the possibility of using overvoltage protection devices for a new type of spark gap based on a multi-segment system in high-voltage networks of a specific country. The analysis of its properties against the background of atmospheric overvoltages and their impact on high voltage lines will be carried out by assessing the effectiveness of the tested overvoltage protection device in laboratory conditions. The tests will also be carried out by applying standardized lightning and switching surges to the tested device to map the overvoltage processes on the power grid elements. Two different generators will be used for this purpose. The proposed research will also allow learning about the influence of structural elements on the operation of the tested devices.


  • Open Access

    Methods of Assessing the Effectiveness of Filter Elements in Power Electronics

    by Michał Borecki, Jan Sroka

    Newly constructed devices must meet a number of requirements in terms of the level of generated disturbances. To achieve an acceptable level in such devices, filters are installed—one of the cheapest ways to reduce interference in devices. One of the key elements of the filter that is responsible for the effectiveness of noise reduction are ferrites. Unfortunately, for various devices, an individual approach should be used in the selection of filters and, accordingly, ferrites. Due to the fact that ferrites from different manufacturers do not have standardized characteristics and information on their effectiveness, the selection of the right ferrite is a very time-consuming process. Therefore, this article will present the possibilities of quickly determining selected ferrite parameters in order to ensure the necessary level of noise reduction. For this purpose, assumptions from the CISPR 17 standard will be used. For selected types of ferrites, a large number of measurements were carried out in order to determine the optimal computational algorithm for adjusting ferrite characteristics to the designed conditions. The performance of these tests will be the basis for conducting tests on a larger number of ferrites, as well as for the development of possible standardization procedures.


  • Open Access

    Comparative Simulation Analysis of Selected Medium and High Voltage Surge Protection Devices

    by Michał Borecki, Yevhen Kharchenko

    The aim of the article is to present and analyze the processes occurring as a result of installing a long flashover arrester (LFA) and a multi-chamber arrester (MCA) as overvoltage protection of power networks. The numerical models of LFA and MCA will be made in order to carry out simulations in the scope of selected structural elements of the considered overvoltage protection device. The above research is a significant supplement to the information on the selection of an effective solution for overvoltage protection.


  • Evaluation of the Effectiveness of Ferrite Characteristics Measurements Based on the CISPR 17 Standard

    by Michal Borecki, Jan Sroka

    The requirements for limiting electromagnetic disturbances result in the need to use appropriately selected elements that suppress the disturbances in question. Therefore, detailed studies of the attenuation efficiency at the design stage should be carried out. The above approach is to ensure adaptation to the current requirements in the field of electromagnetic compatibility. Ferrite cores are the least expensive way to reduce the cost of electromagnetic interference suppression. The structure of ferrite cores is usually mixed, and the nomenclature used by manufacturers is varied. Also, the lack of detailed data on the parameters of the ferrite core may lead to incorrect design assumptions, which results with increased in design costs. Therefore, this article presents in detail the method of assessing the attenuation characteristics of ferrite depending on its parameters, based on the example of specific ferrites. Also, this article shows a methodology for defining the attenuation performance characteristics of selected ferrite cores based on experimental studies. The above-mentioned studies can be helpful by refinement of the CISPR 17 standard. The results presented in this article will indicate the possible range of impedance for the application of the analyzed methods for the evaluation of ferrite damping properties based on CISPR 17.


  • Open Access

    Reliability Assessment of MV Power Connections

    by Piotr Hoduń, Michał Borecki

    This article presents an analysis of the reliability of the power grid using data on the failure rate of the medium voltage (MV) power grid from the last five years. The analysis of the state of the power grid was based on the data provided by the grid operator. The purpose of this article is to analyze the reliability assessment of the medium voltage (MV) power connections using various analytical methods, a simulation model and reliability indicators. The analysis was performed based on the defined categories of power outages in terms of their duration. This made it possible to determine the energy quality indicators in a selected power grid. Then, a more complex analysis was carried out to assess the convergence of the applied analytical models of reliability assessment with the actual results obtained for the power grid. Moreover, using ANSYS Multiphysics, a numerical model of the cable head was developed to analyze the processes taking place in this element of the power grid for various exploitation cases.


  • Open Access

    DESCRIPTION OF ALGORITHMS FOR BALANCING NUMERICAL MATRICES AND THEIR DIVISION INTO HIERARCHICAL LEVELS ACCORDING TO THEIR TYPE AND COMPLEXITY

    by Yuriy Khanas, Michał Borecki

    This article describes a set of algorithms for so-called balancing of numerical matrices, which were developed by the author. Each section consists of several algorithms that are divided into different levels. The order of these levels depended on the chronology of the creation of certain algorithms. Chronology also affected the complexity of these balancing algorithms, so it can be argued that the algorithms are described in order from the simplest level to the most complex. It is important to emphasize that the purpose of the article is to describe the actions on matrices that determine the balancing algorithm of a certain level, and practical application will be the next step.