Carlos Nunes de Carvalho
Carlos Nunes de Carvalho has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Guilherme Lavareda
Universidade Nova de Lisboa
51 shared publications - Ana Amaral
Dept. de Física, Instituto Superior Técnico (UTL), Av. Rovisco Pais 1, 1049-001 Lisboa, Portugal
35 shared publications - Manuela Vieira
Instituto Superior de Engenharia de Lisboa (ISEL), Universidade Politécnica de Lisboa, R. Conselheiro Emídio Navarro, 1959-007 Lisboa, Portugal
18 shared publications - Miguel Fernandes
Departamento de Engenharia Electrónica e Telecomunicações e de Computadores, Instituto Superior de Engenharia de Lisboa, Rua Conselheiro Emídio Navarro 1, 1959-007 Lisboa, Portugal
14 shared publications - Elvira Fortunato
CENIMAT|i3N, Department of Materials Science, School of Science and Technology, NOVA University Lisbon and CEMOP/UNINOVA, 2829-516 Caparica, Portugal
13 shared publications - Alessandro Fantoni
Instituto Superior de Engenharia de Lisboa (ISEL), Polytechnic University of Lisbon, 1549-020 Lisboa, Portugal
11 shared publications
Latest Publications
- 1 December 2019
- Published by Elsevier in Thin Solid Films
- Vol. 691
Conducting indium oxide films on plastic substrates by plasma enhanced reactive thermal evaporation
- 1 December 2019
- Published by Elsevier in Thin Solid Films
- Vol. 691
Conducting indium oxide films on plastic substrates by plasma enhanced reactive thermal evaporation
- 1 February 2019
- Published by Elsevier in Thin Solid Films
- Vol. 671, 49-52
Optical and photoconductive properties of indium sulfide fluoride thin films
- 1 February 2019
- Published by Elsevier in Thin Solid Films
- Vol. 671, 49-52
Optical and photoconductive properties of indium sulfide fluoride thin films
- 15 November 2013
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 78 (2) , 333-351
A CMOS micro power switched-capacitor DC–DC step-up converter for indoor light energy harvesting applications
- 15 November 2013
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 78 (2) , 333-351
A CMOS micro power switched-capacitor DC–DC step-up converter for indoor light energy harvesting applications
- 30 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 122-124
p/n junction depth control using amorphous silicon as a low temperature dopant source
- 30 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 122-124
p/n junction depth control using amorphous silicon as a low temperature dopant source
- 30 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 48-50
Thermal dehydrogenation of amorphous silicon: A time-evolution study
- 30 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 48-50
Thermal dehydrogenation of amorphous silicon: A time-evolution study
- 1 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 3-6
P-type CuxS thin films: Integration in a thin film transistor structure
- 1 September 2013
- Published by Elsevier in Thin Solid Films
- Vol. 543, 3-6
P-type CuxS thin films: Integration in a thin film transistor structure
- 1 December 2012
- Published by Elsevier in Thin Solid Films
- Vol. 526, 221-224
Device quality InOx:Sn and InOx thin films deposited at room temperature with different rf-power densities
- 1 December 2012
- Published by Elsevier in Thin Solid Films
- Vol. 526, 221-224
Device quality InOx:Sn and InOx thin films deposited at room temperature with different rf-power densities
- 14 September 2012
- Published by Wiley in physica status solidi (c)
- Vol. 9 (10-11) , 2198-2202
Thermal dehydrogenation of amorphous silicon deposited on c‐Si: Effect of the substrate temperature during deposition
Samples of doped and undoped a‐Si:H were deposited at temperatures ranging from 100 ºC to 350 ºC and then submitted to different dehydrogenation temperatures (from 350 ºC to 550 ºC) and times (from 1 h to 4 h). a‐Si:H films were characterised after deposition through the measurements of specific material parameters such as: the optical gap, the conductivity at 25 ºC, the thermal activation energy of conductivity and its hydrogen content. Hydrogen content was measured after each thermal treatment. Substrate dopant contamination from phosphorus‐doped a‐Si thin films was evaluated by SIMS after complete dehydrogenation and a junction depth of 0.1 mm was obtained. Dehydrogenation results show a strong dependence of the hydrogen content of the as‐deposited film on the deposition temperature. Nevertheless, the dehydrogenation temperature seems to determine the final H content in a way almost independent from the initial content in the sample. H richer films dehydrogenate faster than films with lower hydrogen concentration
- 14 September 2012
- Published by Wiley in physica status solidi (c)
- Vol. 9 (10-11) , 2198-2202
Thermal dehydrogenation of amorphous silicon deposited on c‐Si: Effect of the substrate temperature during deposition
Samples of doped and undoped a‐Si:H were deposited at temperatures ranging from 100 ºC to 350 ºC and then submitted to different dehydrogenation temperatures (from 350 ºC to 550 ºC) and times (from 1 h to 4 h). a‐Si:H films were characterised after deposition through the measurements of specific material parameters such as: the optical gap, the conductivity at 25 ºC, the thermal activation energy of conductivity and its hydrogen content. Hydrogen content was measured after each thermal treatment. Substrate dopant contamination from phosphorus‐doped a‐Si thin films was evaluated by SIMS after complete dehydrogenation and a junction depth of 0.1 mm was obtained. Dehydrogenation results show a strong dependence of the hydrogen content of the as‐deposited film on the deposition temperature. Nevertheless, the dehydrogenation temperature seems to determine the final H content in a way almost independent from the initial content in the sample. H richer films dehydrogenate faster than films with lower hydrogen concentration
- 1 August 2012
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 12 (8) , 6754-6757
p-Type CuoX Thin Films by rf-Plasma Enhanced Reactive Thermal Evaporation: Influence of rf-Power Density
Copper oxide is a well known p-type semiconductor material, usually obtained by thermal oxidation of copper thin-films within few minutes, at atmospheric pressure. In this paper, thin films of copper oxide that were deposited by radio-frequency plasma enhanced reactive thermal evaporation of copper at room temperature, without any post-deposition annealing treatment, are studied. The deposition of good quality p-type semiconductor oxide to be used in the fabrication of p-TFTs is the purpose of this work. The thickness of the films varies from 97 up to 160 nm. The influence of rf power density on chemical, electrical and optical properties of the films was studied. Samples present conductivity within the range of 6 x 10(-5) to 4 x 10(2) omega(-1) x cm(-1) (thermal activation energy in the interval 0.46 to 0.01 eV). The p-type conductivity of the films was confirmed by Seebeck effect in the more conductive samples. Surface composition obtained by XPS analysis was correlated with optical and electrical properties, showing that rf-power plays a main role in changes of material characteristics.
- 1 August 2012
- Published by American Scientific Publishers in Journal of Nanoscience and Nanotechnology
- Vol. 12 (8) , 6754-6757
p-Type CuoX Thin Films by rf-Plasma Enhanced Reactive Thermal Evaporation: Influence of rf-Power Density
Copper oxide is a well known p-type semiconductor material, usually obtained by thermal oxidation of copper thin-films within few minutes, at atmospheric pressure. In this paper, thin films of copper oxide that were deposited by radio-frequency plasma enhanced reactive thermal evaporation of copper at room temperature, without any post-deposition annealing treatment, are studied. The deposition of good quality p-type semiconductor oxide to be used in the fabrication of p-TFTs is the purpose of this work. The thickness of the films varies from 97 up to 160 nm. The influence of rf power density on chemical, electrical and optical properties of the films was studied. Samples present conductivity within the range of 6 x 10(-5) to 4 x 10(2) omega(-1) x cm(-1) (thermal activation energy in the interval 0.46 to 0.01 eV). The p-type conductivity of the films was confirmed by Seebeck effect in the more conductive samples. Surface composition obtained by XPS analysis was correlated with optical and electrical properties, showing that rf-power plays a main role in changes of material characteristics.