Qiang Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Qiang Guo has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Dengchao Tian
Zhengzhou Institute of Emerging Industrial Technology, zhengzhou, CHINA
4 shared publicationsHuilin Li
Zhengzhou Institute of Emerging Industrial Technology, zhengzhou, CHINA
4 shared publicationsLing Zhang
Institute of Process Engineering, Chinese Academy of Science, Beijing, China
3 shared publicationsMingbo Fu
Zhengzhou Institute of Emerging Industrial Technology, zhengzhou, CHINA
3 shared publicationsYongli Li
CAS Institute of Process Engineering: Institute of Process Engineering Chinese Academy of Sciences
2 shared publications- Yongli Li
State Key Laboratory of Materials Low-Carbon Recycling, College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124, China
2 shared publications
Latest Publications
- 8 March 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 26 (3) , 1517-1526
Non-clay bricks with high compressive strength made from secondary aluminum dross and waste glass
- 8 March 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 26 (3) , 1517-1526
Non-clay bricks with high compressive strength made from secondary aluminum dross and waste glass
- 28 April 2023
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 14 (12) , 4257-4268
Enhanced Hydrolysis of Aluminum Nitride from Secondary Aluminum Dross Through Combination of Wet-Stirred Milling and Alkaline Leaching
- 28 April 2023
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 14 (12) , 4257-4268
Enhanced Hydrolysis of Aluminum Nitride from Secondary Aluminum Dross Through Combination of Wet-Stirred Milling and Alkaline Leaching
- Open Access
Preparation of Foamed Ceramics from Graphite Tailings Using A Self-Foaming Method
Graphite tailings were used as the raw materials for the preparation of foamed ceramics via a high-temperature self-foaming method. The residual carbon in the tailings acted as the foaming agent and no additional foaming agents were required. The residual carbon reacted with Fe2O3 and produced gas that was wrapped by the liquid phase to form a porous structure. The effects of sintering temperature, holding time, carbon content, flux on the bulk density, water absorption, and mean pore size of the foamed ceramics were investigated. The bulk density, compressive strength, thermal conductivity, and water absorption of the foamed ceramic prepared using the optimal sample D100 (100 wt% graphite tailings) and sintered at 1200 °C for 20 min were 1.36 g/cm3, 0.35%, 12.03 MPa, and 0.51 W/(m·K), respectively. The raw material contained CaO, Fe2O3, and SiO2, which formed augite with a low fusibility point. In contrast, the molten decomposition products of potassium feldspar and CaSiO3 ions formed anorthite, which has a high fusibility point. Therefore, potassium feldspar is not recommended for use as a flux in tailing systems with high calcium content. Foamed ceramics were prepared using up to 100 wt% graphite tailings. This is a new approach for the economical disposal of graphite tailings.
Open AccessPreparation of Foamed Ceramics from Graphite Tailings Using A Self-Foaming Method
Graphite tailings were used as the raw materials for the preparation of foamed ceramics via a high-temperature self-foaming method. The residual carbon in the tailings acted as the foaming agent and no additional foaming agents were required. The residual carbon reacted with Fe2O3 and produced gas that was wrapped by the liquid phase to form a porous structure. The effects of sintering temperature, holding time, carbon content, flux on the bulk density, water absorption, and mean pore size of the foamed ceramics were investigated. The bulk density, compressive strength, thermal conductivity, and water absorption of the foamed ceramic prepared using the optimal sample D100 (100 wt% graphite tailings) and sintered at 1200 °C for 20 min were 1.36 g/cm3, 0.35%, 12.03 MPa, and 0.51 W/(m·K), respectively. The raw material contained CaO, Fe2O3, and SiO2, which formed augite with a low fusibility point. In contrast, the molten decomposition products of potassium feldspar and CaSiO3 ions formed anorthite, which has a high fusibility point. Therefore, potassium feldspar is not recommended for use as a flux in tailing systems with high calcium content. Foamed ceramics were prepared using up to 100 wt% graphite tailings. This is a new approach for the economical disposal of graphite tailings.
- Open Access
- 14 September 2022
- Published by Springer Nature in Research Square
Enhanced hydrolysis of aluminium nitride from secondary aluminum dross through combination of wet-stirred milling and alkaline leaching
Deep hydrolysis for removing hazardous aluminium nitride (AlN) from secondary aluminum dross (SAD) remains a challenge nowadays. Enhanced hydrolysis of AlN from SAD through a combination of wet-stirred milling and alkaline leaching is investigated in the present study, which has not been reported before. SAD is activated during wet-stirred milling just with water by reducing the grain size and increasing the active surface area. Leaching with NaOH dissolves the hydrolysis products (AlOOH, Al(OH)3) to expose reactive sites of unhydrolyzed AlN, contributing to the enhanced hydrolysis process. Results indicate that by utilizing optimized conditions (10 min wet milling, 5 wt.% NaOH solution, L/S ratio of 2, 75 ℃ temperature, and 120 min duration), 98.3% of AlN is removed from SAD. The kinetic analysis indicates that the hydrolysis process is controlled by both diffusion and chemical reactions, with the activation energy calculated to be 31.0 kJ/mol. After undergoing this enhanced hydrolysis process, the residue, which consisted primarily of Al2O3 and Al(OH)3,can be recycled as Al concentrate. The technology has been already applied in a pilot plant and achieved a favorable effect in practical applications. Statement of Novelty Efficient hydrolysis for removing hazardous aluminium nitride (AlN) from secondary aluminum dross (SAD) remains a challenge nowadays. An enhanced hydrolysis process for removing AlN from SAD has been developed and reported in this study. The results demonstrate that the progress is highly efficient and can be performed using a combination of wet-stirred milling and alkaline leaching. This solution has not been reported before, and relevant patent authorization has been obtained by our research group. The technology has been already applied in a pilot plant that processes 20000 tons of SAD per year, achieving a favorable effect in practical applications, facilitating the disposal of waste and the protection of environment.
- 14 September 2022
- Published by Springer Nature in Research Square
Open AccessEnhanced hydrolysis of aluminium nitride from secondary aluminum dross through combination of wet-stirred milling and alkaline leaching
Deep hydrolysis for removing hazardous aluminium nitride (AlN) from secondary aluminum dross (SAD) remains a challenge nowadays. Enhanced hydrolysis of AlN from SAD through a combination of wet-stirred milling and alkaline leaching is investigated in the present study, which has not been reported before. SAD is activated during wet-stirred milling just with water by reducing the grain size and increasing the active surface area. Leaching with NaOH dissolves the hydrolysis products (AlOOH, Al(OH)3) to expose reactive sites of unhydrolyzed AlN, contributing to the enhanced hydrolysis process. Results indicate that by utilizing optimized conditions (10 min wet milling, 5 wt.% NaOH solution, L/S ratio of 2, 75 ℃ temperature, and 120 min duration), 98.3% of AlN is removed from SAD. The kinetic analysis indicates that the hydrolysis process is controlled by both diffusion and chemical reactions, with the activation energy calculated to be 31.0 kJ/mol. After undergoing this enhanced hydrolysis process, the residue, which consisted primarily of Al2O3 and Al(OH)3,can be recycled as Al concentrate. The technology has been already applied in a pilot plant and achieved a favorable effect in practical applications. Statement of Novelty Efficient hydrolysis for removing hazardous aluminium nitride (AlN) from secondary aluminum dross (SAD) remains a challenge nowadays. An enhanced hydrolysis process for removing AlN from SAD has been developed and reported in this study. The results demonstrate that the progress is highly efficient and can be performed using a combination of wet-stirred milling and alkaline leaching. This solution has not been reported before, and relevant patent authorization has been obtained by our research group. The technology has been already applied in a pilot plant that processes 20000 tons of SAD per year, achieving a favorable effect in practical applications, facilitating the disposal of waste and the protection of environment.
- 1 October 2021
- Published by Elsevier in Minerals Engineering
- Vol. 172
Innovative technology for defluorination of secondary aluminum dross by alkali leaching
- 1 October 2021
- Published by Elsevier in Minerals Engineering
- Vol. 172
Innovative technology for defluorination of secondary aluminum dross by alkali leaching
- 2 October 2020
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (1) , 56-65
Purification of specularite by centrifugation instead of flotation to produce iron oxide red pigment
- 2 October 2020
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 28 (1) , 56-65
Purification of specularite by centrifugation instead of flotation to produce iron oxide red pigment
- 1 January 2020
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 61 (1) , 42-48
Leaching Ni and Co from Saprolitic Laterite Ore by Employing Atmospheric Acid Leaching Solution with High Concentration of FeCl3 at Mild Conditions
Limonitic and saprolitic laterite ores are used to produce Ni by employing different kinds of processes. Acid leaching is an energy-saving process for pure
- 1 January 2020
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 61 (1) , 42-48
Leaching Ni and Co from Saprolitic Laterite Ore by Employing Atmospheric Acid Leaching Solution with High Concentration of FeCl3 at Mild Conditions
Limonitic and saprolitic laterite ores are used to produce Ni by employing different kinds of processes. Acid leaching is an energy-saving process for pure