Danai Torrungrueng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Danai Torrungrueng has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Hsi-Tseng Chou
Graduate Institute of Communication Engineering National Taiwan University Taipei Taiwan
22 shared publications - Titipong Lertwiriyaprapa
Research Center of Innovation Digital and Electromagnetic Technology (iDEMT), Department of Teacher Training in Electrical Engineering, Faculty of Technical Education, King Mongkut’s University of Technology North Bangkok
12 shared publications - Chuwong Phongcharoenpanich
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand
11 shared publications - Supakit Kawdungta
Faculty of Engineering, Rajamangala University of Technology Lanna, Chiang Mai 50300, Thailand
11 shared publications - Kittisak Phaebua
Research Center of Innovation Digital and Electromagnetic Technology (iDEMT), Faculty of Technical Education, King Mongkuts University of Technology North Bangkok, Bangkok, Thailand
10 shared publications - Akkarat Boonpoonga
Department of Electrical and Computer Engineering, Faculty of Engineering, King Mongkuts University of Technology North Bangkok, Bangkok, Thailand
6 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by MDPI AG in Electronics
- Vol. 15 (20) , 4843
Mechanically Tunable Microstrip Bandpass Filter Using a Planar Cycloid-Dipole Resonant Superstrate
This paper presents the design, simulation, and experimental validation of a mechanically tunable microstrip bandpass filter employing a planar cycloid-dipole resonant superstrate. The proposed filter is based on a coupled-line bandpass topology, in which frequency tunability is achieved through electromagnetic field perturbation induced by vertical displacement of the resonant superstrate. By adjusting the air gap between the superstrate and the microstrip structure, continuous frequency tuning is achieved without modifying the underlying filter topology. The simulated results demonstrate an operating passband tuning range from 2.41 to 2.52 GHz for superstrate separations of 0.5–1.0 mm, whereas the fabricated prototype exhibits a measured passband tuning range from 2.32 to 2.49 GHz for separations of 0.5–1.0 mm, corresponding to a measured tuning span of 170 MHz. Throughout the measured tuning range, |S11| remains below −10 dB, while the measured insertion loss is approximately 2.5 dB near the passband center. Furthermore, electromagnetic field distributions and CST-extracted effective propagation parameters are examined to provide qualitative insight into the influence of superstrate displacement on the observed frequency-tuning behavior. The results demonstrate the feasibility of the proposed simple and passive mechanical tuning approach for frequency-reconfigurable filtering applications in the 2.4 GHz ISM band.
- 20 October 2026
- Published by MDPI AG in Electronics
- Vol. 15 (20) , 4843
Open AccessMechanically Tunable Microstrip Bandpass Filter Using a Planar Cycloid-Dipole Resonant Superstrate
This paper presents the design, simulation, and experimental validation of a mechanically tunable microstrip bandpass filter employing a planar cycloid-dipole resonant superstrate. The proposed filter is based on a coupled-line bandpass topology, in which frequency tunability is achieved through electromagnetic field perturbation induced by vertical displacement of the resonant superstrate. By adjusting the air gap between the superstrate and the microstrip structure, continuous frequency tuning is achieved without modifying the underlying filter topology. The simulated results demonstrate an operating passband tuning range from 2.41 to 2.52 GHz for superstrate separations of 0.5–1.0 mm, whereas the fabricated prototype exhibits a measured passband tuning range from 2.32 to 2.49 GHz for separations of 0.5–1.0 mm, corresponding to a measured tuning span of 170 MHz. Throughout the measured tuning range, |S11| remains below −10 dB, while the measured insertion loss is approximately 2.5 dB near the passband center. Furthermore, electromagnetic field distributions and CST-extracted effective propagation parameters are examined to provide qualitative insight into the influence of superstrate displacement on the observed frequency-tuning behavior. The results demonstrate the feasibility of the proposed simple and passive mechanical tuning approach for frequency-reconfigurable filtering applications in the 2.4 GHz ISM band.
- Open Access
- 3 May 2026
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 61 (5)
A Low‐Cost Via‐Less Air‐Filled Waveguide in Multilayer PCB for High‐Frequency Circuits Based on Artificial Magnetic Conductors
This paper proposes a novel, low‐cost, AMC‐based via‐less approach to implementing air‐filled waveguides (AFWs) embedded within multilayer printed circuit board structures to achieve low propagation loss. Three layers of low‐cost FR4 substrates are sandwiched together using prepreg to form the basic AFW structure. To overcome the technical impossibility of seamless vertical metalization in multilayer LCP or FR4 processes, an electroplating technology combined with planar artificial magnetic conductor (AMC) surfaces is employed to construct the waveguide sidewalls. The AMC structures effectively create a virtual magnetic wall that suppresses electromagnetic (EM) leakage through the unplated prepreg layers. To further enhance field confinement and reduce junction leakage, a modified AMC structure incorporating longitudinal metal strips is introduced. Numerical simulations at 77 GHz demonstrate that the proposed AFW achieves a remarkably low theoretical propagation loss of 0.08 dB/cm. A prototype was fabricated and measured to validate the design. While transition‐region fabrication sensitivities affected the absolute insertion loss, the intrinsic propagation loss of the waveguide core was extracted using a multi‐length transmission line method, yielding an experimental result of 0.16 dB/cm. The proposed architecture provides a highly integrable, cost‐effective, and high‐performance solution for millimeter‐wave (mmWave) and sub‐terahertz applications, such as automotive radar and 5G/6G communications, where traditional substrate‐integrated waveguides (SIW) suffer from high dielectric losses.
- 3 May 2026
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 61 (5)
Open AccessA Low‐Cost Via‐Less Air‐Filled Waveguide in Multilayer PCB for High‐Frequency Circuits Based on Artificial Magnetic Conductors
This paper proposes a novel, low‐cost, AMC‐based via‐less approach to implementing air‐filled waveguides (AFWs) embedded within multilayer printed circuit board structures to achieve low propagation loss. Three layers of low‐cost FR4 substrates are sandwiched together using prepreg to form the basic AFW structure. To overcome the technical impossibility of seamless vertical metalization in multilayer LCP or FR4 processes, an electroplating technology combined with planar artificial magnetic conductor (AMC) surfaces is employed to construct the waveguide sidewalls. The AMC structures effectively create a virtual magnetic wall that suppresses electromagnetic (EM) leakage through the unplated prepreg layers. To further enhance field confinement and reduce junction leakage, a modified AMC structure incorporating longitudinal metal strips is introduced. Numerical simulations at 77 GHz demonstrate that the proposed AFW achieves a remarkably low theoretical propagation loss of 0.08 dB/cm. A prototype was fabricated and measured to validate the design. While transition‐region fabrication sensitivities affected the absolute insertion loss, the intrinsic propagation loss of the waveguide core was extracted using a multi‐length transmission line method, yielding an experimental result of 0.16 dB/cm. The proposed architecture provides a highly integrable, cost‐effective, and high‐performance solution for millimeter‐wave (mmWave) and sub‐terahertz applications, such as automotive radar and 5G/6G communications, where traditional substrate‐integrated waveguides (SIW) suffer from high dielectric losses.
- Open Access
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 65315-65325
Design and Validation of a Rotatable Gap-Waveguide Rotman Lens BFN for a Cylindrically Conformal Slot Array
This paper presents the design and experimental validation of a two-dimensional (2-D) circularly cylindrical phased array antenna with integrated wide-angle beam-switching capability for multibeam radiation in the Ku-band. The antenna consists of a conformal array of waveguide (WG) slot columns, excited by a compact, Rotman lens-based beamforming network (RL-BFN). A key innovation is the realization of this RL-BFN using gap-waveguide technology, enabling its non-contact integration beneath the antenna aperture. This unique configuration permits the mechanical rotation of the entire RL-BFN to electronically switch beams and significantly extend the angular coverage, a feature not feasible with traditional fixed-feed networks. The lens profile is synthesized using an exact trifocal solution, specifically adapted for the conformal array geometry. The proposed system achieves a beam steering range exceeding ±30° with a simulated beamforming efficiency greater than 92% for broadside radiation. Both full-wave simulations and measurements of a fabricated prototype validate the design concept, demonstrating its potential for high-efficiency, low-loss microwave communication links.
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 65315-65325
Open AccessDesign and Validation of a Rotatable Gap-Waveguide Rotman Lens BFN for a Cylindrically Conformal Slot Array
This paper presents the design and experimental validation of a two-dimensional (2-D) circularly cylindrical phased array antenna with integrated wide-angle beam-switching capability for multibeam radiation in the Ku-band. The antenna consists of a conformal array of waveguide (WG) slot columns, excited by a compact, Rotman lens-based beamforming network (RL-BFN). A key innovation is the realization of this RL-BFN using gap-waveguide technology, enabling its non-contact integration beneath the antenna aperture. This unique configuration permits the mechanical rotation of the entire RL-BFN to electronically switch beams and significantly extend the angular coverage, a feature not feasible with traditional fixed-feed networks. The lens profile is synthesized using an exact trifocal solution, specifically adapted for the conformal array geometry. The proposed system achieves a beam steering range exceeding ±30° with a simulated beamforming efficiency greater than 92% for broadside radiation. Both full-wave simulations and measurements of a fabricated prototype validate the design concept, demonstrating its potential for high-efficiency, low-loss microwave communication links.
- Open Access
- 3 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 52467-52478
Circularly Polarized Antenna With Polarization-Compliable PRS Unit Cells for Gain Enhancement and Sidelobe Suppression
This paper presents a compact circularly polarized (CP) antenna that achieves high gain and low sidelobe levels (SLL) using a single-layer polarization-compliable partially reflective surface (PRS). Each PRS unit cell combines overlapping cross- and rectangular-slot elements to provide balanced reflection responses for vertical and horizontal polarizations while suppressing cross-polarization. By jointly optimizing the reflection magnitude and phase of both polarizations, the proposed PRS achieves uniform aperture-field distribution that enhances gain and preserves edge tapering for SLL suppression. In addition, alternative analysis framework in which the PRS layer modeled as a Bi-Characteristic-Impedance Transmission Line (BCITL) is proposed. By retrieving the BCITL parameters (Z0+, Z0-, γ) from Floquet-mode S-parameters of the PRS unit cell, the method reveals the intrinsic propagation constant of the PRS layer and clarifies the relation between the PRS reflection coefficient and the BCITL parameters (Z0+, Z0-, γ). This dual viewpoint full-wave plus BCITL enables more physical insight into how the PRS height, co- and cross- polarized reflection coefficients, and edge taper collectively influence the gain and SLL trade-off. The retrieved cross-polarized propagation constants exhibit strong attenuation, confirming that cross-polarized modes are effectively suppressed thus maintaining the purity of the CP main beam and low SLL. A corner-trimmed square patch antenna operating at 10 GHz is used to validate the concept, achieving a simulated gain increase from 5.8 to 24 dBic with SLLs below −22 dB, axial ratio (AR) < 2.5 dB. The proposed PRS features an aperture of 6.27λ×6.27λ and a compact thickness of only 0.5λ (λ denotes the free space wavelength), achieving a simulated aperture efficiency of 60%. Measurement results confirm the simulations and validate the effectiveness of the proposed design, validating both the design concept and the BCITL-based interpretation.
- 3 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 52467-52478
Open AccessCircularly Polarized Antenna With Polarization-Compliable PRS Unit Cells for Gain Enhancement and Sidelobe Suppression
This paper presents a compact circularly polarized (CP) antenna that achieves high gain and low sidelobe levels (SLL) using a single-layer polarization-compliable partially reflective surface (PRS). Each PRS unit cell combines overlapping cross- and rectangular-slot elements to provide balanced reflection responses for vertical and horizontal polarizations while suppressing cross-polarization. By jointly optimizing the reflection magnitude and phase of both polarizations, the proposed PRS achieves uniform aperture-field distribution that enhances gain and preserves edge tapering for SLL suppression. In addition, alternative analysis framework in which the PRS layer modeled as a Bi-Characteristic-Impedance Transmission Line (BCITL) is proposed. By retrieving the BCITL parameters (Z0+, Z0-, γ) from Floquet-mode S-parameters of the PRS unit cell, the method reveals the intrinsic propagation constant of the PRS layer and clarifies the relation between the PRS reflection coefficient and the BCITL parameters (Z0+, Z0-, γ). This dual viewpoint full-wave plus BCITL enables more physical insight into how the PRS height, co- and cross- polarized reflection coefficients, and edge taper collectively influence the gain and SLL trade-off. The retrieved cross-polarized propagation constants exhibit strong attenuation, confirming that cross-polarized modes are effectively suppressed thus maintaining the purity of the CP main beam and low SLL. A corner-trimmed square patch antenna operating at 10 GHz is used to validate the concept, achieving a simulated gain increase from 5.8 to 24 dBic with SLLs below −22 dB, axial ratio (AR) < 2.5 dB. The proposed PRS features an aperture of 6.27λ×6.27λ and a compact thickness of only 0.5λ (λ denotes the free space wavelength), achieving a simulated aperture efficiency of 60%. Measurement results confirm the simulations and validate the effectiveness of the proposed design, validating both the design concept and the BCITL-based interpretation.
- 6 February 2026
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 61 (2)
Environmental Boundary Estimation of Urban Areas Using FMCW Radar With Data Clustering for UAV Detection
The increasing presence of unmanned aerial vehicles (UAVs) in urban environments presents challenges for reliable detection due to clutter caused by buildings, infrastructure, and other static structures. Conventional Doppler‐based radar methods often struggle in such conditions, particularly when UAVs exhibit low radial velocities. This paper presents a non‐Doppler scattering‐point framework for UAV detection, based on a frequency‐modulated continuous wave (FMCW) radar system operating in the X‐band (9.950–10.026 GHz). The system utilizes a rotating platform for azimuth scanning and applies azimuth‐range mapping combined with adaptive DBSCAN clustering and β ‐expanded convex hull boundary estimation to reduce false detections from static clutter. Experimental validation was conducted in a controlled urban setting with multiple buildings and varied UAV trajectories. The method was evaluated across several elevation angles, demonstrating consistent detection performance and improved distinction between UAV detections and points caused by environmental clutter. These results support the use of FMCW radar and spatial clustering techniques as an effective alternative to Doppler‐independent methods for UAV monitoring in complex environments.
- 6 February 2026
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 61 (2)
Environmental Boundary Estimation of Urban Areas Using FMCW Radar With Data Clustering for UAV Detection
The increasing presence of unmanned aerial vehicles (UAVs) in urban environments presents challenges for reliable detection due to clutter caused by buildings, infrastructure, and other static structures. Conventional Doppler‐based radar methods often struggle in such conditions, particularly when UAVs exhibit low radial velocities. This paper presents a non‐Doppler scattering‐point framework for UAV detection, based on a frequency‐modulated continuous wave (FMCW) radar system operating in the X‐band (9.950–10.026 GHz). The system utilizes a rotating platform for azimuth scanning and applies azimuth‐range mapping combined with adaptive DBSCAN clustering and β ‐expanded convex hull boundary estimation to reduce false detections from static clutter. Experimental validation was conducted in a controlled urban setting with multiple buildings and varied UAV trajectories. The method was evaluated across several elevation angles, demonstrating consistent detection performance and improved distinction between UAV detections and points caused by environmental clutter. These results support the use of FMCW radar and spatial clustering techniques as an effective alternative to Doppler‐independent methods for UAV monitoring in complex environments.
- Open Access
- 14 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (2) , 483-497
Adaptive Sampling for Spherical Near-Field Antenna Measurements via Uncertainty-Driven Gaussian Process Regression
This paper proposes an adaptive sampling technique for spherical near-field (SNF) antenna measurements that leverages the predictive uncertainty of Gaussian process regression (GPR) to guide measurement point selection. This framework bridges Bayesian machine learning and antenna metrology, enabling real-time adaptive sampling. Unlike conventional uniform or clustering-based methods, the proposed approach iteratively refines the sampling grid by prioritizing regions with high uncertainty, particularly within the high-intensity near-field or other defined regions of interest. This uncertainty-driven GPR strategy enables high-fidelity far-field (FF) reconstruction with substantially fewer measurements. In conventional low-cost SNF systems, the probe must stop at every measurement point to reduce vibration, making the stop-and-go process time-consuming. In contrast, the proposed method minimizes unnecessary stops by targeting only high-uncertainty regions, offering significant advantages in research and development and production-line environments. In such cases, the optimized sampling points identified during the initial adaptive process can be reused, enabling rapid and efficient FF characterization without repeating the full measurement cycle. The method is validated through both full-wave simulations and experimental measurements involving various antenna types, including a large commercial base station antenna. Results demonstrate that the proposed approach achieves up to a 77% reduction in sampling points compared to uniform sampling, while maintaining FF pattern correlation exceeding 99.35%. Overall, the technique offers a statistically grounded and time-efficient solution for high-fidelity antenna characterization with reduced measurement effort.
- 14 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (2) , 483-497
Open AccessAdaptive Sampling for Spherical Near-Field Antenna Measurements via Uncertainty-Driven Gaussian Process Regression
This paper proposes an adaptive sampling technique for spherical near-field (SNF) antenna measurements that leverages the predictive uncertainty of Gaussian process regression (GPR) to guide measurement point selection. This framework bridges Bayesian machine learning and antenna metrology, enabling real-time adaptive sampling. Unlike conventional uniform or clustering-based methods, the proposed approach iteratively refines the sampling grid by prioritizing regions with high uncertainty, particularly within the high-intensity near-field or other defined regions of interest. This uncertainty-driven GPR strategy enables high-fidelity far-field (FF) reconstruction with substantially fewer measurements. In conventional low-cost SNF systems, the probe must stop at every measurement point to reduce vibration, making the stop-and-go process time-consuming. In contrast, the proposed method minimizes unnecessary stops by targeting only high-uncertainty regions, offering significant advantages in research and development and production-line environments. In such cases, the optimized sampling points identified during the initial adaptive process can be reused, enabling rapid and efficient FF characterization without repeating the full measurement cycle. The method is validated through both full-wave simulations and experimental measurements involving various antenna types, including a large commercial base station antenna. Results demonstrate that the proposed approach achieves up to a 77% reduction in sampling points compared to uniform sampling, while maintaining FF pattern correlation exceeding 99.35%. Overall, the technique offers a statistically grounded and time-efficient solution for high-fidelity antenna characterization with reduced measurement effort.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 10, 47-59
A Compact Implantable UHF-RFID Rectenna Tag for Implantable Bolus-Based Wireless Animal Tracking
This paper proposes a compact implantable ultra-high frequency (UHF) radio frequency identification (RFID) rectenna tag designed for integration into an implantable bolus for in-body wireless animal tracking. The integrated design achieves dual functionality: passive RFID tag (920–925MHz) and RF energy harvesting via a Schottky diode rectifier. The rectenna tag structure incorporates a meandered dipole antenna with T-matching, optimized for conjugate impedance matching with a passive RFID chip operating in the 920–925 MHz band. A loop structure is integrated with a Schottky diode to enable RF-to-DC power conversion. Full-wave simulations within high-dielectric media (εr = 40–80) modeling internal bolus conditions demonstrate an input impedance of 30 + j300 Ω, exhibiting an omnidirectional radiation pattern with a gain of −19.0 dBi (RFID port) and -18.0 dBi (rectenna port), and a specific absorption rate (SAR) in 1 g of 0.231 W/kg and 0.336 W/kg, respectively. The system demonstrates an RF power harvesting efficiency of up to 10-20%. A prototype was fabricated and tested in water, achieving maximum read ranges of 2.0 m (free space) and 1.4 m (aqueous environment). Measured gains were -15.0 dBi (RFID port) and -18.0 dBi (Rectenna port). The measured SAR also remained at 0.27 W/kg (RFID tag port) and 0.35 W/kg (Rectenna port), well within established safety limits. These results validate the proposed rectenna tag as a promising solution for efficient and safe in-body animal tracking via implantable bolus tags. The system integrates a passive RFID chip and RF-DC rectifier, enabling dual-functionality: battery-free real-time animal identification and self-powered physiological sensing (e.g., rumen temperature/pH) for livestock health monitoring.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 10, 47-59
A Compact Implantable UHF-RFID Rectenna Tag for Implantable Bolus-Based Wireless Animal Tracking
This paper proposes a compact implantable ultra-high frequency (UHF) radio frequency identification (RFID) rectenna tag designed for integration into an implantable bolus for in-body wireless animal tracking. The integrated design achieves dual functionality: passive RFID tag (920–925MHz) and RF energy harvesting via a Schottky diode rectifier. The rectenna tag structure incorporates a meandered dipole antenna with T-matching, optimized for conjugate impedance matching with a passive RFID chip operating in the 920–925 MHz band. A loop structure is integrated with a Schottky diode to enable RF-to-DC power conversion. Full-wave simulations within high-dielectric media (εr = 40–80) modeling internal bolus conditions demonstrate an input impedance of 30 + j300 Ω, exhibiting an omnidirectional radiation pattern with a gain of −19.0 dBi (RFID port) and -18.0 dBi (rectenna port), and a specific absorption rate (SAR) in 1 g of 0.231 W/kg and 0.336 W/kg, respectively. The system demonstrates an RF power harvesting efficiency of up to 10-20%. A prototype was fabricated and tested in water, achieving maximum read ranges of 2.0 m (free space) and 1.4 m (aqueous environment). Measured gains were -15.0 dBi (RFID port) and -18.0 dBi (Rectenna port). The measured SAR also remained at 0.27 W/kg (RFID tag port) and 0.35 W/kg (Rectenna port), well within established safety limits. These results validate the proposed rectenna tag as a promising solution for efficient and safe in-body animal tracking via implantable bolus tags. The system integrates a passive RFID chip and RF-DC rectifier, enabling dual-functionality: battery-free real-time animal identification and self-powered physiological sensing (e.g., rumen temperature/pH) for livestock health monitoring.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 1
UAV Localization with Ghost-Target Suppression using Scanning FMCW Radar and Integrated Deep Neural Networks
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 1
UAV Localization with Ghost-Target Suppression using Scanning FMCW Radar and Integrated Deep Neural Networks
- Open Access
Additively Manufactured Mechanically Tunable Cavity Resonator for Broadband Characterization of Liquid Permittivity
This paper presents the design, fabrication, and experimental validation of a metal 3D-printed mechanically tunable cavity resonator operating in the hybrid TM–coaxial resonant mode for the broadband characterization of liquid permittivity. The proposed structure was developed based on a cylindrical cavity by incorporating a disc-terminated metallic tuning stub, which enables continuous frequency adjustment from 0.5 GHz to 3.0 GHz while maintaining a maximum unloaded Q-factor of 284 at 1 GHz under air-filled conditions. The tuning mechanism allows for precise frequency selection for characterizing materials exhibiting frequency-dependent permittivity. To demonstrate its sensing capability, the resonator was applied to characterize ethanol–water mixtures, where resonant frequency shifts were correlated with ethanol concentration at representative baseline frequencies of 1.00 GHz, 2.00 GHz, and 2.94 GHz. The sensor achieved frequency/dielectric constant resolutions of 0.39, 1.34, and 4.20 MHz and average concentration errors of 1.25%, 3.73%, and 2.49%, respectively. Moreover, polynomial fitting models enabled the accurate extraction of dielectric constants with an average deviation below 0.5% compared with a commercial dielectric probe system. The combination of frequency tunability, compact geometry, and compatibility with additive manufacturing establishes the proposed cavity resonator as a versatile platform for broadband dielectric spectroscopy, chemical sensing, and liquid characterization.
Open AccessAdditively Manufactured Mechanically Tunable Cavity Resonator for Broadband Characterization of Liquid Permittivity
This paper presents the design, fabrication, and experimental validation of a metal 3D-printed mechanically tunable cavity resonator operating in the hybrid TM–coaxial resonant mode for the broadband characterization of liquid permittivity. The proposed structure was developed based on a cylindrical cavity by incorporating a disc-terminated metallic tuning stub, which enables continuous frequency adjustment from 0.5 GHz to 3.0 GHz while maintaining a maximum unloaded Q-factor of 284 at 1 GHz under air-filled conditions. The tuning mechanism allows for precise frequency selection for characterizing materials exhibiting frequency-dependent permittivity. To demonstrate its sensing capability, the resonator was applied to characterize ethanol–water mixtures, where resonant frequency shifts were correlated with ethanol concentration at representative baseline frequencies of 1.00 GHz, 2.00 GHz, and 2.94 GHz. The sensor achieved frequency/dielectric constant resolutions of 0.39, 1.34, and 4.20 MHz and average concentration errors of 1.25%, 3.73%, and 2.49%, respectively. Moreover, polynomial fitting models enabled the accurate extraction of dielectric constants with an average deviation below 0.5% compared with a commercial dielectric probe system. The combination of frequency tunability, compact geometry, and compatibility with additive manufacturing establishes the proposed cavity resonator as a versatile platform for broadband dielectric spectroscopy, chemical sensing, and liquid characterization.
- Open Access
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 187273-187284
Single-Layer Asymmetric PRS Based on Compact Microstrip Resonant Cells for Broadband Antenna Gain Enhancement
In this paper, a novel single-layer asymmetric partially reflective surface (PRS) based on compact microstrip resonant cells (CMRCs) is proposed for gain enhancement of a Fabry-Pérot cavity (FPC) antenna over a wide bandwidth. It overcomes the conventional PRS’s narrow gain bandwidth limitation caused by the frequency dependence of their reflection phase. The proposed PRS consists of two different CMRC patterns etched on the top and bottom of a single dielectric layer. This configuration produces a positive gradient in the reflection phase response and double resonances that merge in the reflection magnitude response, resulting in a broadband characteristic. Due to its inherent asymmetric property, the bi-characteristic-impedance transmission line (BCITL), which can effectively represent asymmetric reciprocal transmission lines (ARTLs), is used to accurately model and analyze the CMRC-based PRS. The results show good agreement with those of the full-wave simulation. A prototype of the optimized FPC antenna was fabricated and tested. The measurement results, within the operating frequency band of 5.15 GHz to 6.0 GHz, show an improvement in gain of 5 dB compared to the reference antenna, with a peak gain of 10.18 dBi and a 3-dB gain bandwidth of 15.72%.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 187273-187284
Open AccessSingle-Layer Asymmetric PRS Based on Compact Microstrip Resonant Cells for Broadband Antenna Gain Enhancement
In this paper, a novel single-layer asymmetric partially reflective surface (PRS) based on compact microstrip resonant cells (CMRCs) is proposed for gain enhancement of a Fabry-Pérot cavity (FPC) antenna over a wide bandwidth. It overcomes the conventional PRS’s narrow gain bandwidth limitation caused by the frequency dependence of their reflection phase. The proposed PRS consists of two different CMRC patterns etched on the top and bottom of a single dielectric layer. This configuration produces a positive gradient in the reflection phase response and double resonances that merge in the reflection magnitude response, resulting in a broadband characteristic. Due to its inherent asymmetric property, the bi-characteristic-impedance transmission line (BCITL), which can effectively represent asymmetric reciprocal transmission lines (ARTLs), is used to accurately model and analyze the CMRC-based PRS. The results show good agreement with those of the full-wave simulation. A prototype of the optimized FPC antenna was fabricated and tested. The measurement results, within the operating frequency band of 5.15 GHz to 6.0 GHz, show an improvement in gain of 5 dB compared to the reference antenna, with a peak gain of 10.18 dBi and a 3-dB gain bandwidth of 15.72%.