HNHamed Nikfarjam

Hamed Nikfarjam

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hamed Nikfarjam has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Electrothermally Actuated Bulk-Mode Silicon Resonators in the GHz Range

    by Sepehr Sheikhlari, Hamed Nikfarjam, Prithviraj Palit, Milad Daneshnazar, Siavash Pourkamali

    This study presents the fabrication and characterization of a bulk mode, thermally actuated silicon resonator that utilizes a piezoresistive readout mechanism. Implementing bulk-mode actuation facilitates the attainment of operating frequencies within the ultrahigh frequency (UHF) range and beyond, thus reducing the requirement to scale the resonator dimensions to the nanoscale. In this investigation, dual-block crystalline silicon resonators were fabricated and successfully operated, demonstrating a first bulk-mode extensional resonance frequency of 488 MHz and 1.6 GHz. The measured quality factors were 2800 and 1200. Furthermore, active motional resistance values as low as $- 150~\Omega $ (corresponding to a motional conductance of −6.68 mA/V) and $- 455~\Omega $ (with a motional conductance of −2.25 mA/V) were achieved for the fabricated resonators, highlighting their efficacy in high-frequency operation applications.

  • Study of Stiction Mitigation in Micromachine Structures via Naphthalene Sublimation

    by Hamed Nikfarjam, Sepehr Sheikhlari, Siavash Pourkamali

    Micromachined devices are susceptible to stiction failure, where suspended structures irreversibly adhere due to surface forces. This paper investigates the effectiveness and reproducibility of simple, low-cost sublimation methods to reduce stiction using a saturated naphthalene-isopropyl alcohol (IPA) solution or molten naphthalene. Six categories of test structures were fabricated on silicon-on-insulator wafers, including narrow and wide cantilevers, clamped-clamped beams, parallel clamped-clamped beams, meandering beams, and suspended proof masses. We evaluated the effectiveness of air drying, IPA rinse, supercritical point drying (CPD), naphthalene-IPA solution, and molten naphthalene by identifying the longest and least stiff intact structure released for each method. Results showed that molten naphthalene outperformed CPD for wider structures, and reproducibility was confirmed over 10 repetitions per structure and method. These cost-effective, room-temperature techniques are well-suited for mitigating stiction in larger and softer structures, enhancing accessibility and availability for MEMS fabrication. 2024-0170


  • Electrothermal Bimorph MEMS Sensor for Helium Detection

    by Sulaiman Mohaidat, Hamed Nikfarjam, Mutaz Fayad, Siavash Pourkamali, Fadi Alsaleem

    This paper reports a method for detecting helium in atmospheric air based on the thermal conductivity of helium using a bimorph micro-structure. The bimorph structure is designed to deflect less with helium’s presence than air under Jole heating’s application. The COMSOL Multiphysics finite element software was used to design and verify the operation of the structure. Based on the simulation, Si/SiO2 bimorph micro-cantilever structures with trenches were fabricated and experimentally tested to detect the presence of helium. The detection difference due to the presence of helium measured using a digital hologram microscope was 30 nm, which closely matched what we reported in the simulation. Further simulation results were conducted to vary some design parameters in the sensor, showing that the sensor performance can be improved significantly to around 15 times. The best-explored design parameters were found to be a cantilever with a 5 μm thickness and a gas gap thickness of 2 μm. This paper provides proof of concept for developing a capacitive electrothermal MEMS helium sensor that can be used in many critical applications, such as monitoring nuclear waste stored in pressurized helium dry casks.


  • Open Access

    Energy efficient integrated MEMS neural network for simultaneous sensing and computing

    by Hamed Nikfarjam, Mohammad Megdadi, Mohammad Okour, Siavash Pourkamali, Fadi Alsaleem

    Biological systems seamlessly combine multiple functions in lightweight and energy-efficient structures. Such capability in synthetic structures would be desirable in numerous engineering applications such as aerospace, robotics and wearable devices. Here we report an integrated silicon-based structure configured to sense, perform different classification algorithms, and produce an action signal within the same physical layer. The algorithms are coded in the mechanical responses of the sensing elements of multiple coupled micro-electro-mechanical systems (MEMS), simultaneously capturing acceleration measurements to produce an actuated signal. This all-in-one structure operates with zero circuitry and low power consumption. As a demonstration, we designed and fabricated a network of three MEMS neurons to successfully perform both simple signal classification and activity recognition problems (standing and sitting) with only 9.92 × 10−17 kWh and 17.79 × 10−19 kWh energy consumption per operation, respectively. Our approach will enable emergent technologies, such as wearable devices, to perform complex computations with power from a single battery charge.


  • Theoretical and Experimental Investigation of Using Multidegree of Freedom Electrostatically Actuated Microstructures in Performing Classification Problems

    by Hamed Nikfarjam, Mohammad Megdadi, Mohammad Okour, Siavash Pourkamali, Fadi Alsaleem

    This paper demonstrates the use of micro-electromechanical systems to perform an efficient classification problem. Classification using digital computers is inefficient due to its power requirement and the separation between memory and processing units. As a proof of concept, basic signal classification has been performed using a network of only three mechanically coupled devices. The classification occurred at the hardware level rather than using a digital computer. The classification problem involves distinguishing between a ramp signal versus a step input signal. In this demonstration, a three-degree of freedom model was built for the proposed network in MATLAB. Detailed simulation results were extracted to validate the network operation and sensitivity to operating conditions. Next, the device network hardware was fabricated and tested to perform the required classification problem. Good agreement between simulation and experiment is demonstrated.


  • Stiction Reduction in MEMS Fabrication via Naphthalene Sublimation

    by Hamed Nikfarjam, Sepehr Sheikhlari, Siavash Pourkamali

    This work describes a simple low-cost method to prevent stiction in low-stiffness suspended microstructures via naphthalene sublimation. Different microstructure types with different lengths and therefore different stiffness were fabricated and released using this technique. The results show great improvement when compared to water release. The method uses naphthalene crystal sediments acting as temporary support underneath and between suspended microstructures during solvent evaporation. Results show a significant reduction of stiction compared to similar structures released and dried without this procedure.


  • Open Access

    Exploiting Pull-In/Pull-Out Hysteresis in Electrostatic MEMS Sensor Networks to Realize a Novel Sensing Continuous-Time Recurrent Neural Network

    by Mohammad H Hasan, Amin Abbasalipour, Hamed Nikfarjam, Siavash Pourkamali, Muhammad Emad-Ud-Din, Roozbeh Jafari, Fadi Alsaleem

    The goal of this paper is to provide a novel computing approach that can be used to reduce the power consumption, size, and cost of wearable electronics. To achieve this goal, the use of microelectromechanical systems (MEMS) sensors for simultaneous sensing and computing is introduced. Specifically, by enabling sensing and computing locally at the MEMS sensor node and utilizing the usually unwanted pull in/out hysteresis, we may eliminate the need for cloud computing and reduce the use of analog-to-digital converters, sampling circuits, and digital processors. As a proof of concept, we show that a simulation model of a network of three commercially available MEMS accelerometers can classify a train of square and triangular acceleration signals inherently using pull-in and release hysteresis. Furthermore, we develop and fabricate a network with finger arrays of parallel plate actuators to facilitate coupling between MEMS devices in the network using actuating assemblies and biasing assemblies, thus bypassing the previously reported coupling challenge in MEMS neural networks.


  • An 8-Bit Digitally Operated Micromachined Accelerometer

    by Amin Abbasalipour, Hamed Nikfarjam, Siavash Pourkamali

    This work presents successful implementation and characterization of an 8-bit digitally operated micromachined accelerometer. Such device is comprised of an electrostatically tunable acceleration switch with 8 sets of electrostatic tuning electrodes. Similar to bits in a binary number, the tuning force of each electrode set increases by a factor of 2 with respect to the adjacent electrode set. A fabricated device has been interfaced with a micro-controller performing a binary search by controlling state of different tuning electrodes (ON or OFF) to interpret the acceleration with 8 bits of resolution. Measurement results show good agreement between the applied acceleration and the binary acceleration output of the sensor reported by the controller. The tested 8-bit prototype has full-scale acceleration of 2.7g with resolution 10.5 mg s (1/2 8 of full scale). Requiring only a bias voltage for operation (zero static current) and readout of the switch output (a digital high or low voltage) that can be performed directly by a digital controller, such devices can lead to ultra-low power accelerometers by eliminating the need for an analog-front-end.