HLHaoqi Li

Haoqi Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Haoqi Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dual-Parameter Diagnosis of Gas Turbine Blade Fatigue Cracks Based on Blade Tip Timing Data

    by Shuming Wu, Haoqi Li, Liqin Lu, Shangqin You, Zhibo Yang, Jiahui Cao, Xuefeng Chen, Danhui Yang

    Gas turbine rotor blade cracks are usually caused by high-cycle fatigue. The natural frequency and damping of the blades change as the cracks propagate. Most existing methods detect fatigue cracks by observing the decrease in natural frequency, which may lead to misjudgment. This article proposes a method for diagnosing blade fatigue cracks by combining the indicators of natural frequency decrease and damping ratio increase. Extracting these two parameters using blade tip timing (BTT) data faces challenges such as signal undersampling and errors in identifying the resonance location due to different sensor layouts. This article introduces a method for extracting natural frequency and damping using only two sensors under uniform acceleration (sweep frequency) excitation. For natural frequency extraction, an adaptive window length sparse representation method is proposed, which can adaptively select the spectral window parameters based on the sampled data and effectively reduce leakage by adding weighting factors. For damping extraction, a center-fixed half-power bandwidth method is proposed. This method improves the half-power bandwidth method by locating the resonance center based on the extracted natural frequency, avoiding interference from “dip” data caused by different sensor layouts. Finally, an accelerated fatigue experiment on a blisk verifies the accuracy of the extracted parameters and the sensitivity of the natural frequency and damping indicators to fatigue cracks.


  • Open Access

    A Novel Blade Vibration Monitoring Experimental System Based on Blade Tip Sensing

    by Haoqi Li, Shaohua Tian, Zhibo Yang

    Due to its non-intrusive manner, blade tip timing (BTT) is considered a potential tool for the condition monitoring of turbomachinery. The challenge of BTT relates to significant under-sampled signal processing, which is induced by a lower number of probes. Signal processing assumes that the ability of the hardware system can meet the requirements of the software algorithm. The abilities of the hardware, including the time resolution of the data acquisition system (DAS) and the dynamic characteristics of rigs, are compromised, particularly when the rotating speed increases. This increase in speed causes two problems for BTT: (1) the rig is less stable, due to the reduction of dynamic stiffness; (2) the time resolution of the DAS can be inadequate for identification. To promote the performance of the hardware system, here a BTT rig was designed with high dynamic performance, including a new DAS with a time resolution of 10 ns. A variety of commonly used BTT signal processing methods are used to analyze the experimental data and verify the good reliability and validity of the experimental platform.


  • Biprobes Blade Tip Timing Method for Frequency Identification Based on Active Aliasing Time-Delay Estimation and Dealiasing

    by Jiahui Cao, Zhibo Yang, Shaohua Tian, Haoqi Li, Ruochen Jin, Ruqiang Yan, Xuefeng Chen

    Rotating blades are key turbomachinery components with high failure risk due to harsh working conditions. Thus, monitoring the running state of blades is urgently required. Blade tip timing (BTT) is regarded as a potential technology for blade vibration monitoring owing to its noncontact nature and low cost. However, severe undersampling and strict probe layout hinder the application of BTT. As a result of severe undersampling, aliasing and its suppression are the main research topics in BTT. However, in this article, a biprobes method for BTT based on the utilization of aliasing is proposed to identify the natural frequencies of blades. Active aliasing is used in this method to produce aliasing findings at various equivalent sampling frequencies, and the closed-form robust Chinese remainder theorem is used for dealiasing. Unlike the conventional multirate sampling systems for BTT that use a multiprobe configuration or varied speed, the suggested method utilizes varying delay durations to obtain varying equivalent sample frequencies. Furthermore, to ensure that active aliasing and dealiasing form a closed loop, an included angle coprime layout is proposed. Finally, the robustness and effectiveness of the proposed method are verified through numerical and experimental validation.


  • Blade Tip Timing Signal Filtering Method Based on Sampling Aliasing Frequency Map

    by Jiahui Cao, Shaohua Tian, Zhibo Yang, Guangrong Teng, Haoqi Li, Ruochen Jin, Ruqiang Yan, Xuefeng Chen

    The rotor blade is the core turbomachinery component with high failure risk. Thus, condition monitoring of blades is critical to ensure engine safety. Blade tip timing (BTT) is one of the most promising approaches to measure vibration, which is used for monitoring the health of blades. In reality, blade displacement contains several unwanted components that cause measurement uncertainty. However, because undersampling leads to spectrum aliasing, and the aliasing frequency changes with speed fluctuation, conventional filtering techniques fail to remove the portion of the signal that causes uncertainty. In this work, two filtering methods for the BTT signal are proposed based on sampling aliasing frequency (SAFE) map, namely, single-probe data detrending and tracking sliding bandpass filtering, which can extract synchronous vibration and denoise the reserved signal (asynchronous vibration) due to the clear distribution of different components in the SAFE map. The former eliminates the rotation frequency and its harmonic components by detrending of the BTT signal, whereas the latter effectively reduces the noise of the BTT signal by bandpass filters whose limit frequencies are adjusted according to sampling frequency and the trajectory in the SAFE map. Furthermore, the time-domain signal and the spectrum obtained by the orthogonal matching pursuit (OMP) algorithm are used to show the filtering effect. The effectiveness and interpretability of the proposed method are verified by simulation and experimental data.


  • Single-Probe Blade Tip Timing: A Novel Method for Anomaly Identification Based on Frequency Shift

    by Jiahui Cao, Zhibo Yang, Haoqi Li, Zengkun Wang, Shaohua Tian, Laihao Yang, Xuefeng Chen

    Blades are weak and essential parts of an aeroengine. Monitoring the running state of blades is essential for ensuring the safety of aeroengine operation. Blade tip timing (BTT) is considered a promising technique for operational blade vibration monitoring for turbomachinery; however, it is difficult to analyze the BTT signal because of the inherent undersampled limitation. To overcome this limitation, the minimal sensor layout scheme is restricted to be “three.” Usually, more than five probes are required for good signal revolution. This requirement is an installation restriction that limits the application of BTT; however, for users, the conflict between probe layout optimization and real installation restriction is also a serious problem. Motivated by these issues, a single-probe BTT (SP-BTT) method is proposed; the SP-BTT method could extract the shift between natural frequencies, which could be used as a damage index for blade condition monitoring. To validate the effectiveness of the proposed method, numerical simulations and experimental tests are performed.


  • Adaptive Iterative Approach for Efficient Signal Processing of Blade Tip Timing

    by Haoqi Li, Zhibo Yang, Shuming Wu, Zengkun Wang, Shaohua Tian, Ruqiang Yan, Xuefeng Chen

    Blade health monitoring (BHM) is an important technology to ensure safe operation of turbine machinery. The blade tip timing (BTT) method is a non-contact approach of vibration monitoring that is widely used for aero-engines. A BTT signal can be characterized as nonuniform and sub-Nyquist sampled (i.e., under-sampled). For nonuniform sampling, the least squares (LS) fitting method has long been used to reconstruct the spectrum. However, the under-sampling of the BTT signal causes the spectrum obtained by LS fitting aliasing. The iterative reweighted LS periodogram (IRLSP) can eliminate the aliasing caused by sub-Nyquist and nonuniform sampling. This method weakens the frequency aliasing through the method of reweighted iteration, but the consequence of this operation is that the amount of calculation is greatly increased. Thus, we propose an adaptive iterative approach (AIA) based on the IRLSP that combines a priori information of the blade. The main contribution of this method is to improve the computational efficiency for processing the BTT signal and the effect of anti-aliasing. These two points mean that this method is expected to become a real-time blade vibration monitoring method. We combined a finite element model with modal testing to perform simulations and verify the improvement with AIA. A large number of experiments were also performed to verify the effectiveness of our approach for BHM.


  • Open Access

    Index evaluation of overall stability of small-span steel plate bridge

    by Haoqi Li

    Based on a 3×35m steel plate bridge of a highway project, a nonlinear entity model is established using finite element software, and the structure is evaluated with the stability safety factor as the evaluation index. Through the analysis of different parameters, some conclusions are drawn to satisfy the stability of the bridge structure.

  • Blade Crack Detection using Blade Tip Timing

    by Shuming Wu, Zengkun Wang, Haoqi Li, Zhibo Yang, Shaohua Tian, Ruqiang Yan, Shibin Wang, Xuefeng Chen

    The harsh working environment of compressor threats the integrality of bladed disk. Crack is one of the most fatal faults of rotating blades. Detecting the crack of blades at early stage could ensure the safe operation of gas turbine and save economic costs. Blade tip timing (BTT) is a noncontact blade vibration measurement technique, which is widely used in recent years. In this article, a procedure of crack detection using BTT data is proposed. First, some typical parameters are taken into consideration, including resonance frequency, amplitude change of natural frequency, amplitude of blade tip, phase, and interblade spacing. It has been found that the frequency of the blade will decrease with the increment of crack length and reduction of crack height. In addition, the resonance frequency of the bladed disk will split when the blade cracks. The amplitude of different orders of resonance frequency varies with cracks. The amplitude of the first order changes very slightly, whereas the second and third orders are relatively obvious. The blade tip vibration amplitude and phase change with cracks without obvious regularity. The interblade distance will change due to the appearance of cracks. According to the above rules, the frequency and the interblade distance are adopted as crack diagnosis indicators. First, we use the Lomb-Scargle periodogram to quickly determine whether the crack appears and then use the blade frequency and interblade distance to locate the number of the blade having crack. In the experimental test, BTT data measured on a titanium bladed disk is used to verify the effectiveness of our method.


  • Open Access

    Wavelet Element Modelling for Inviscid Fluid–Solid Coupling Problem based on Partitioned Approach

    by Zhi-Bo Yang, Hao-Qi Li, Bai-Jie Qiao, Xue-Feng Chen

    To provide a simple numerical formulation based on fixed grids, a wavelet element method for fluid–solid modelling is introduced in this work. Compared with the classical wavelet finite element method, the presented method can potentially handle more complex shapes. Considering the differences between the solid and fluid regions, a damping-like interface based on wavelet elements is designed, in order to ensure consistency between the two parts. The inner regions are constructed with the same wavelet function in space. In the time and spatial domains, a partitioned approach based on Jacobi iteration is combined with the pseudo-parallel calculation method. Numerical convergence analyses show that the method can serve as an alternative choice for fluid–solid coupling modelling.


  • An Improved Multiple Signal Classification for Nonuniform Sampling in Blade Tip Timing

    by Zengkun Wang, Zhibo Yang, Shuming Wu, Haoqi Li, Shaohua Tian, Xuefeng Chen

    Blade tip timing (BTT) is an effective non-contact measurement technology for rotating blade health monitoring. However, due to the mismatching between the high-speed rotation and the limited amount of probes, the signal collected from BTT system is severely under-sampled, which induces the difficulty in feature extraction. Multiple signal classification (MUSIC) has the potential to overcome the under-sampled problem once the probes are properly placed. Whereas, if traditional MUSIC is directly used in BTT, the accuracy of frequency identification cannot be high enough and the identified numbers of frequency components are also severely restrained. To address these two problems, an improved MUSIC is proposed as an alternative methodology to extract the blade vibration frequency for BTT. Based on the orthogonality of the signal subspace and the noise subspace from under-sampled signal, the presented method can effectively identify the vibration frequency components from the under-sampled signal of BTT.