Na Peng
Na Peng has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Dixian Zhao
Southeast University
5 shared publications - Peng Gu
Southeast University
5 shared publications - Xiaohu You
Southeast University
4 shared publications - Jiajun Zhang
National Mobile Communication Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
3 shared publications - Mengru Yang
National Mobile Communications Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
3 shared publications - Yongran Yi
National Mobile Communication Research Laboratory, School of Information Science and Engineering, Southeast University, Nanjing, China
3 shared publications
Latest Publications
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (6) , 768-771
A 1.9-dB NF K-Band Temperature-Healing Phased-Array Receiver Employing Hybrid Packaged 65-nm CMOS Beamformer and 0.1-μm GaAs LNAs
A 1.9-dB NF K-band phased-array receiver (RX) is presented, which employs the hybrid packaged 65-nm CMOS beamformer and 0.1- $\mu \text{m}$ GaAs LNAs based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. Power-efficient gain and phase tuning blocks are utilized to reduce power consumption. Temperature-healing design methodology is adopted to ensure nearly constant gain response versus temperature variations. The proposed phased-array RX only consumes 30.2-mW dc power per channel and achieves < 1.2-dB gain variation and < 0.9-dB NF variation from −40 °C to 85 °C.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (6) , 768-771
A 1.9-dB NF K-Band Temperature-Healing Phased-Array Receiver Employing Hybrid Packaged 65-nm CMOS Beamformer and 0.1-μm GaAs LNAs
A 1.9-dB NF K-band phased-array receiver (RX) is presented, which employs the hybrid packaged 65-nm CMOS beamformer and 0.1- $\mu \text{m}$ GaAs LNAs based on the fan-out wafer-level chip-scale packaging (WLCSP) technology. Power-efficient gain and phase tuning blocks are utilized to reduce power consumption. Temperature-healing design methodology is adopted to ensure nearly constant gain response versus temperature variations. The proposed phased-array RX only consumes 30.2-mW dc power per channel and achieves < 1.2-dB gain variation and < 0.9-dB NF variation from −40 °C to 85 °C.
- Top Cited Papers
- 1 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (10) , 3977-3990
Millimeter-Wave Integrated Phased Arrays
Large-scale millimeter-wave (mm-Wave) integrated phased array is the key technology to enable broadband 5G and satellite communications. This paper details the design considerations, challenges and trade-offs of mm-Wave integrated phased arrays based on bulk CMOS and multi-layer hybrid PCB technologies. Both technologies attain high yield and low cost for mass production. Important beamforming building blocks are addressed and compared in detail. Demonstrators of integrated phased arrays are presented from circuit to board levels. The 1024- and 4096-element integrated phased arrays achieve the EIRP of 72.5 and 84.0 dBm respectively. Finally, relevant phased-array transceivers and antennas from the recent literature are discussed.
- 1 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (10) , 3977-3990
Top Cited PapersMillimeter-Wave Integrated Phased Arrays
Large-scale millimeter-wave (mm-Wave) integrated phased array is the key technology to enable broadband 5G and satellite communications. This paper details the design considerations, challenges and trade-offs of mm-Wave integrated phased arrays based on bulk CMOS and multi-layer hybrid PCB technologies. Both technologies attain high yield and low cost for mass production. Important beamforming building blocks are addressed and compared in detail. Demonstrators of integrated phased arrays are presented from circuit to board levels. The 1024- and 4096-element integrated phased arrays achieve the EIRP of 72.5 and 84.0 dBm respectively. Finally, relevant phased-array transceivers and antennas from the recent literature are discussed.
- Open Access
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 110026-110038
A Ka-Band Balanced Four-Beam Phased-Array Receiver With Symmetrical Beam-Distribution Network in 65-nm CMOS
This paper demonstrates a Ka-band CMOS phased-array receiver capable of generating four balanced beams from two inputs. A passive four-beam symmetrical differential network is proposed to distribute two input signals to eight channels and facilitate beam generation at the outputs in the receiver. The detailed design and optimization of the passive four-beam differential network are presented. Using a 6-bit passive vector-modulated phase shifter and a 5-bit switched-type attenuator in each channel, we implement a phase control of 360° with<; 4° RMS phase error and a gain control of 17 dB with <; 0.35 dB RMS gain error from 27 to 31 GHz. The receiver consumes a current of only 40 mA under 1 V supply voltage. Eight channels of the four-beam phased-array receiver were measured and a gain mismatch of less than 0.3 dB has been achieved. Beam to beam couplings are investigated by measurements and beam-to-beam isolation are better than 32 dB from 27 to 31 GHz. The chip size is 2.6×4 mm 2 including all digital control circuitry and pads.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 110026-110038
Open AccessA Ka-Band Balanced Four-Beam Phased-Array Receiver With Symmetrical Beam-Distribution Network in 65-nm CMOS
This paper demonstrates a Ka-band CMOS phased-array receiver capable of generating four balanced beams from two inputs. A passive four-beam symmetrical differential network is proposed to distribute two input signals to eight channels and facilitate beam generation at the outputs in the receiver. The detailed design and optimization of the passive four-beam differential network are presented. Using a 6-bit passive vector-modulated phase shifter and a 5-bit switched-type attenuator in each channel, we implement a phase control of 360° with<; 4° RMS phase error and a gain control of 17 dB with <; 0.35 dB RMS gain error from 27 to 31 GHz. The receiver consumes a current of only 40 mA under 1 V supply voltage. Eight channels of the four-beam phased-array receiver were measured and a gain mismatch of less than 0.3 dB has been achieved. Beam to beam couplings are investigated by measurements and beam-to-beam isolation are better than 32 dB from 27 to 31 GHz. The chip size is 2.6×4 mm 2 including all digital control circuitry and pads.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 410-413
A Ka-Band CMOS 4-Beam Phased-Array Receiver With Symmetrical Beam-Distribution Network
This paper demonstrates a Ka-band 4-beam phased array receiver in 65-nm CMOS. To generate four balanced beams from two inputs, a passive 4-beam symmetrical differential network is employed to achieve balanced signal distribution. With the use of passive vector-modulated phase shifter and switched-type attenuator, the receiver consumes a current of only 40 mA under 1 V supply voltage. The 4-beam receiver shows 3 dB gain per channel. From 27 to 31 GHz, the RMS gain error and phase error are < 0.4 dB and < 4∘, respectively. Beam to beam couplings are investigated and the measured beam-to-beam isolation is better than -32 dB from 27 to 31 GHz. The chip size is 2.6 × 4 mm2 with pads included. To author’s knowledge, this work reports the first CMOS phased-array receiver with four balanced beams.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 410-413
A Ka-Band CMOS 4-Beam Phased-Array Receiver With Symmetrical Beam-Distribution Network
This paper demonstrates a Ka-band 4-beam phased array receiver in 65-nm CMOS. To generate four balanced beams from two inputs, a passive 4-beam symmetrical differential network is employed to achieve balanced signal distribution. With the use of passive vector-modulated phase shifter and switched-type attenuator, the receiver consumes a current of only 40 mA under 1 V supply voltage. The 4-beam receiver shows 3 dB gain per channel. From 27 to 31 GHz, the RMS gain error and phase error are < 0.4 dB and < 4∘, respectively. Beam to beam couplings are investigated and the measured beam-to-beam isolation is better than -32 dB from 27 to 31 GHz. The chip size is 2.6 × 4 mm2 with pads included. To author’s knowledge, this work reports the first CMOS phased-array receiver with four balanced beams.