Anna Sandinge
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anna Sandinge has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Per Blomqvist
RISE Research Institutes of Sweden Boras Sweden
5 shared publications Per Blomqvist
RISE Research Institutes of Sweden Boras Sweden
3 shared publicationsAnne Dederichs
RISE Research Institutes of Sweden Boras Sweden
2 shared publications- Eric Guillaume
Efectis France Saint‐Aubin France
2 shared publications Henrik Fredriksson
Fire and Safety RISE Research Institutes of Sweden Borås Sweden
2 shared publicationsLars Schiøtt Sørensen
DTU Technical University of Denmark Kongens Lyngby Denmark
2 shared publications
Latest Publications
- Open Access
- 11 August 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (7) , 752-770
Wildfire Emissions From European Boreal Fuels: Effects of Fuel Type and Moisture Content
The increasing severity of wildfires poses significant challenges through the release of greenhouse gases and other harmful gases and particles. Although field measurements exist, there is a lack of systematic data collection to understand the influence of moisture content on the particle and gas emissions of boreal fuels, particularly for European boreal forest fuels. This study investigates the influence of moisture content and fuel type on flaming combustion emission characteristics of surface fuels collected from two Swedish forest types, which share key characteristics with fire‐prone forests across the European boreal. The results are based on bench‐scale controlled combustion conditions in a cone calorimeter, where gaseous and particle emissions were measured using Fourier Transform Infrared spectroscopy and an Electrical Low‐Pressure Impactor, respectively. Moisture content of the fuels only insignificantly affected combustion efficiency, with higher moisture content leading to increased emissions of incomplete combustion products (CO, CH 4 and NH 3 ). Thus, although moisture affects the amount of fine fuel consumed in a wildfire, it is not significant for the emissions factors during the flaming combustion. The combustion of mosses was instead significantly less efficient than that of litter for all moisture contents. Average emission factors highlighted clear differences between fuel types, with mosses producing higher CO (87 ± 20 g/kg) and lower CO 2 (1350 ± 220 g/kg) compared to litter (47 ± 12 g/kg and 1620 ± 81 g/kg, respectively). Particle emissions were strongly dependent on fuel type with of 29 ± 12 g/kg for mosses compared to 98 ± 15 g/kg for Pinus sylvestris needles and twigs.
- 11 August 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (7) , 752-770
Open AccessWildfire Emissions From European Boreal Fuels: Effects of Fuel Type and Moisture Content
The increasing severity of wildfires poses significant challenges through the release of greenhouse gases and other harmful gases and particles. Although field measurements exist, there is a lack of systematic data collection to understand the influence of moisture content on the particle and gas emissions of boreal fuels, particularly for European boreal forest fuels. This study investigates the influence of moisture content and fuel type on flaming combustion emission characteristics of surface fuels collected from two Swedish forest types, which share key characteristics with fire‐prone forests across the European boreal. The results are based on bench‐scale controlled combustion conditions in a cone calorimeter, where gaseous and particle emissions were measured using Fourier Transform Infrared spectroscopy and an Electrical Low‐Pressure Impactor, respectively. Moisture content of the fuels only insignificantly affected combustion efficiency, with higher moisture content leading to increased emissions of incomplete combustion products (CO, CH 4 and NH 3 ). Thus, although moisture affects the amount of fine fuel consumed in a wildfire, it is not significant for the emissions factors during the flaming combustion. The combustion of mosses was instead significantly less efficient than that of litter for all moisture contents. Average emission factors highlighted clear differences between fuel types, with mosses producing higher CO (87 ± 20 g/kg) and lower CO 2 (1350 ± 220 g/kg) compared to litter (47 ± 12 g/kg and 1620 ± 81 g/kg, respectively). Particle emissions were strongly dependent on fuel type with of 29 ± 12 g/kg for mosses compared to 98 ± 15 g/kg for Pinus sylvestris needles and twigs.
- 16 March 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (4) , 460-476
Interlaboratory Evaluation of ISO / TS 21397: FTIR Gas Analysis Coupled With Cone Calorimeter
The quantitative analysis of fire effluents is essential for assessing both toxic hazards and combustion chemistry. ISO/TS 21397 specifies the use of Fourier transform infrared (FTIR) spectroscopy coupled to cone calorimeter tests for the online measurement of fire gases. To evaluate the robustness of this method, an interlaboratory round robin was conducted under the framework of ISO/TC 92. Six laboratories participated, four of which provided complete FTIR datasets. Four polymers were selected to represent different effluent profiles: high‐density polyethylene (HDPE), polymethyl methacrylate (PMMA), polyamide 6.6 (PA 6.6), and unplasticised polyvinyl chloride (PVC). Each laboratory performed three replicate cone calorimeter tests at 50 kW/m 2 . Combustion parameters (peak heat release rate, total heat release, effective heat of combustion) and effluent species were analysed. Qualitative results showed consistent identification of expected major species: carbon dioxide (CO 2 ) and carbon monoxide (CO) for all polymers, nitric oxide (NO) for PA 6.6 and hydrogen chloride (HCl) for PVC. Quantitative analysis focused on maximum concentrations and yields of CO 2 , CO, NO and HCl. Statistical treatment following ISO 5725 provided complete repeatability and reproducibility values. The results revealed a clear hierarchy in reproducibility: combustion parameters showed the lowest variability, followed by CO 2 , then CO, with NO and HCl exhibiting higher dispersion. Minor species such as HCN and NO 2 were detected inconsistently and excluded from statistical treatment. The study confirms that ISO/TS 21397 yields reproducible data for the major effluents of interest, while highlighting the need for more prescriptive guidance on calibration and quantification methods to further improve interlaboratory agreement.
- 16 March 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (4) , 460-476
Interlaboratory Evaluation of ISO / TS 21397: FTIR Gas Analysis Coupled With Cone Calorimeter
The quantitative analysis of fire effluents is essential for assessing both toxic hazards and combustion chemistry. ISO/TS 21397 specifies the use of Fourier transform infrared (FTIR) spectroscopy coupled to cone calorimeter tests for the online measurement of fire gases. To evaluate the robustness of this method, an interlaboratory round robin was conducted under the framework of ISO/TC 92. Six laboratories participated, four of which provided complete FTIR datasets. Four polymers were selected to represent different effluent profiles: high‐density polyethylene (HDPE), polymethyl methacrylate (PMMA), polyamide 6.6 (PA 6.6), and unplasticised polyvinyl chloride (PVC). Each laboratory performed three replicate cone calorimeter tests at 50 kW/m 2 . Combustion parameters (peak heat release rate, total heat release, effective heat of combustion) and effluent species were analysed. Qualitative results showed consistent identification of expected major species: carbon dioxide (CO 2 ) and carbon monoxide (CO) for all polymers, nitric oxide (NO) for PA 6.6 and hydrogen chloride (HCl) for PVC. Quantitative analysis focused on maximum concentrations and yields of CO 2 , CO, NO and HCl. Statistical treatment following ISO 5725 provided complete repeatability and reproducibility values. The results revealed a clear hierarchy in reproducibility: combustion parameters showed the lowest variability, followed by CO 2 , then CO, with NO and HCl exhibiting higher dispersion. Minor species such as HCN and NO 2 were detected inconsistently and excluded from statistical treatment. The study confirms that ISO/TS 21397 yields reproducible data for the major effluents of interest, while highlighting the need for more prescriptive guidance on calibration and quantification methods to further improve interlaboratory agreement.
- Open Access
- 6 February 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (3) , 318-333
The Reaction‐to‐Fire Performance of Intumescent Coating After Ageing by Thermal and Moisture Exposure
Materials and products age with time and their properties change. It is known that, for example, the mechanical strength may be deteriorated from ageing. To understand the ageing effect on the fire behaviour of materials and products is important to maintain the safety level of the construction or application. In this study, three different sandwich panels with intumescent coatings were selected for a study to evaluate the effect of accelerated ageing on reaction‐to‐fire properties. The accelerated ageing methods used were thermal exposure in 90°C and moisture exposure in 40°C and 90% RH. Samples were collected from ageing chambers after 1, 2 and 4 weeks. The reaction‐to‐fire properties were evaluated using the ISO 5660‐1 cone calorimeter and the smoke density chamber, EN ISO 5659‐2, with FTIR analysis of gas composition. The results show that ageing has an effect on the fire behaviour. Fire properties such as heat release rate and smoke production were unchanged or actually improved. Generally, the time to ignition was longer for the aged samples. The smoke density was affected as well as the smoke toxicity.
- 6 February 2026
- Published by Wiley in Fire and Materials
- Vol. 50 (3) , 318-333
Open AccessThe Reaction‐to‐Fire Performance of Intumescent Coating After Ageing by Thermal and Moisture Exposure
Materials and products age with time and their properties change. It is known that, for example, the mechanical strength may be deteriorated from ageing. To understand the ageing effect on the fire behaviour of materials and products is important to maintain the safety level of the construction or application. In this study, three different sandwich panels with intumescent coatings were selected for a study to evaluate the effect of accelerated ageing on reaction‐to‐fire properties. The accelerated ageing methods used were thermal exposure in 90°C and moisture exposure in 40°C and 90% RH. Samples were collected from ageing chambers after 1, 2 and 4 weeks. The reaction‐to‐fire properties were evaluated using the ISO 5660‐1 cone calorimeter and the smoke density chamber, EN ISO 5659‐2, with FTIR analysis of gas composition. The results show that ageing has an effect on the fire behaviour. Fire properties such as heat release rate and smoke production were unchanged or actually improved. Generally, the time to ignition was longer for the aged samples. The smoke density was affected as well as the smoke toxicity.
- Open Access
- 21 February 2023
- Published by Wiley in Fire and Materials
- Vol. 47 (7) , 910-924
Fire safety of interior materials of buses
- 21 February 2023
- Published by Wiley in Fire and Materials
- Vol. 47 (7) , 910-924
Open AccessFire safety of interior materials of buses
- Open Access
- 4 August 2022
- Published by Wiley in Fire and Materials
- Vol. 47 (2) , 270-281
Evaluation of smoke gas toxicity and smoke density of bus interior materials
- 4 August 2022
- Published by Wiley in Fire and Materials
- Vol. 47 (2) , 270-281
Open AccessEvaluation of smoke gas toxicity and smoke density of bus interior materials
- Open Access
- 26 November 2021
- Published by Springer Nature in Fire Technology
- Vol. 58 (3) , 1305-1332
The Effect of Accelerated Ageing on Reaction-to-Fire Properties–Composite Materials
As material age, the durability, strength, and other mechanical properties are impacted. The lifespan of a material generally decreases when exposed to weathering conditions such as wind, temperature, humidity, and light. It is important to have knowledge of how materials age and how the material properties are affected. Regarding materials´ fire behaviour and the effect of ageing on these properties, the knowledge is limited. The research questions of the current work are: Are the fire properties of composite materials affected by ageing? And if so, how is it affected? The study is on material at Technology Readiness Level 9 (TRL). In this study, three composite fibre laminates developed for marine applications were exposed to accelerated ageing. Two different ageing conditions were selected, thermal ageing with an increased temperature of 90°C and moisture ageing in a moderately increased temperature of 40°C and a relative humidity of 90%. Samples were collected after one, two and four weeks of ageing. The reaction-to-fire properties after ageing was evaluated using the ISO 5660–1 cone calorimeter and the EN ISO 5659–2 smoke chamber with FTIR gas analysis. The test results showed that the fire behaviour was affected. Two of the composite laminates, both phenolic/basalt composites, showed a deteriorated fire behaviour from the thermal ageing and the third composite laminate, a PFA/glass fibre composite, showed an improved fire behaviour both for thermal and moisture ageing. The smoke toxicity was affected by the accelerated ageing, especially for the PFA/glass fibre composite that showed a higher production of CO and HCN, both for the thermal aged and the moisture aged samples.
- 26 November 2021
- Published by Springer Nature in Fire Technology
- Vol. 58 (3) , 1305-1332
Open AccessThe Effect of Accelerated Ageing on Reaction-to-Fire Properties–Composite Materials
As material age, the durability, strength, and other mechanical properties are impacted. The lifespan of a material generally decreases when exposed to weathering conditions such as wind, temperature, humidity, and light. It is important to have knowledge of how materials age and how the material properties are affected. Regarding materials´ fire behaviour and the effect of ageing on these properties, the knowledge is limited. The research questions of the current work are: Are the fire properties of composite materials affected by ageing? And if so, how is it affected? The study is on material at Technology Readiness Level 9 (TRL). In this study, three composite fibre laminates developed for marine applications were exposed to accelerated ageing. Two different ageing conditions were selected, thermal ageing with an increased temperature of 90°C and moisture ageing in a moderately increased temperature of 40°C and a relative humidity of 90%. Samples were collected after one, two and four weeks of ageing. The reaction-to-fire properties after ageing was evaluated using the ISO 5660–1 cone calorimeter and the EN ISO 5659–2 smoke chamber with FTIR gas analysis. The test results showed that the fire behaviour was affected. Two of the composite laminates, both phenolic/basalt composites, showed a deteriorated fire behaviour from the thermal ageing and the third composite laminate, a PFA/glass fibre composite, showed an improved fire behaviour both for thermal and moisture ageing. The smoke toxicity was affected by the accelerated ageing, especially for the PFA/glass fibre composite that showed a higher production of CO and HCN, both for the thermal aged and the moisture aged samples.
- 9 November 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (13) , 51861
Systematic evaluation of bromine‐free flame‐retardant systems in acrylonitrile‐butadiene‐styrene
A systematic investigation of phosphorus‐based flame‐retardant (PFR) systems in acrylonitrile‐butadiene‐styrene (ABS) is presented. The effect of various PFRs, combinations thereof and influence of different synergists is studied in terms of fire and mechanical performance, as well as toxicity of resulting ABS. Sustainable flame‐retardant systems with a promising effect on the fire‐retardant properties of ABS are identified: A combination of aluminum diethylphosphinate and ammonium polyphosphate is shown to exhibit superior flame‐retardant properties in ABS compared to other studied PFRs and PFR combinations. Among a variety of studied potential synergists for this system, a grade of expandable graphite with a high‐initiation temperature and a molybdenum‐based smoke suppressant show the most promising effect, leading to a significant reduction of the peak heat release rate as well as the smoke production rate. Compared to current state‐of‐the‐art brominated flame‐retardant for ABS, the identified flame‐retardant systems reduce the maximum smoke production rate by 70% and the peak heat release rate by 40%. However, a significant reduction of the impact performance of the resulting ABS is identified, which requires further investigation.
- 9 November 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (13) , 51861
Systematic evaluation of bromine‐free flame‐retardant systems in acrylonitrile‐butadiene‐styrene
A systematic investigation of phosphorus‐based flame‐retardant (PFR) systems in acrylonitrile‐butadiene‐styrene (ABS) is presented. The effect of various PFRs, combinations thereof and influence of different synergists is studied in terms of fire and mechanical performance, as well as toxicity of resulting ABS. Sustainable flame‐retardant systems with a promising effect on the fire‐retardant properties of ABS are identified: A combination of aluminum diethylphosphinate and ammonium polyphosphate is shown to exhibit superior flame‐retardant properties in ABS compared to other studied PFRs and PFR combinations. Among a variety of studied potential synergists for this system, a grade of expandable graphite with a high‐initiation temperature and a molybdenum‐based smoke suppressant show the most promising effect, leading to a significant reduction of the peak heat release rate as well as the smoke production rate. Compared to current state‐of‐the‐art brominated flame‐retardant for ABS, the identified flame‐retardant systems reduce the maximum smoke production rate by 70% and the peak heat release rate by 40%. However, a significant reduction of the impact performance of the resulting ABS is identified, which requires further investigation.
- 7 June 2021
- Published by Wiley in Fire and Materials
- Vol. 45 (8) , 1085-1095
An experimental evaluation of the equivalence ratios in tests apparatus used for fire effluent toxicity studies
Summary: An experimental evaluation was conducted on the bench‐scale test methods most commonly applied for generating data for fire toxicity assessments. The test methods evaluated were ISO/TS 19700, ISO 5660‐1 with the controlled atmosphere box, and ISO 5659‐2. Toxic gases were quantitatively analyzed using Fourier transfer infrared spectroscopy. Tests were made with 11 different insulation materials and polymethylmethacrylate as a reference material. The evaluation made was on the combustion conditions in the test apparatus, not generally on the precise yields measured. The evaluation focused on the ventilation conditions created in flaming combustion tests. It was seen that ISO/TS 19700 currently offers the best means among the three test methods evaluated for conducting tests at pre‐determined and controlled equivalence ratios. The controlled‐atmosphere cone calorimeter does not give a prolonged steady flaming combustion period for most materials and the influence of vitiation was difficult to predict and limiting in achieving higher equivalence ratios, with the test settings applied. ISO 5659‐2 generally accumulates a mixture of gases from periods of both flaming and nonflaming combustion in a test, and the yields measured do not, in those cases, represent any specific combustion stage. For materials not showing flaming combustion, for example, mineral fiber products, the influence on the test conditions regarding oxygen consumption and heat generation from the material itself is limited compared to burning materials. However, there were specific properties and limitations of the different test methods observed that are important to consider.
- 7 June 2021
- Published by Wiley in Fire and Materials
- Vol. 45 (8) , 1085-1095
An experimental evaluation of the equivalence ratios in tests apparatus used for fire effluent toxicity studies
Summary: An experimental evaluation was conducted on the bench‐scale test methods most commonly applied for generating data for fire toxicity assessments. The test methods evaluated were ISO/TS 19700, ISO 5660‐1 with the controlled atmosphere box, and ISO 5659‐2. Toxic gases were quantitatively analyzed using Fourier transfer infrared spectroscopy. Tests were made with 11 different insulation materials and polymethylmethacrylate as a reference material. The evaluation made was on the combustion conditions in the test apparatus, not generally on the precise yields measured. The evaluation focused on the ventilation conditions created in flaming combustion tests. It was seen that ISO/TS 19700 currently offers the best means among the three test methods evaluated for conducting tests at pre‐determined and controlled equivalence ratios. The controlled‐atmosphere cone calorimeter does not give a prolonged steady flaming combustion period for most materials and the influence of vitiation was difficult to predict and limiting in achieving higher equivalence ratios, with the test settings applied. ISO 5659‐2 generally accumulates a mixture of gases from periods of both flaming and nonflaming combustion in a test, and the yields measured do not, in those cases, represent any specific combustion stage. For materials not showing flaming combustion, for example, mineral fiber products, the influence on the test conditions regarding oxygen consumption and heat generation from the material itself is limited compared to burning materials. However, there were specific properties and limitations of the different test methods observed that are important to consider.
- 16 February 2021
- Published by Wiley in Fire and Materials
- Vol. 46 (1) , 80-94
A modified specimen holder for cone calorimeter testing of composite materials to reduce influence from specimen edges
SUMMARY: ISO 5660‐1 specifies the cone calorimeter method for characterizing the ignition and surface burning behavior of materials. The specimen is irradiated through a square opening in the frame of the specimen holder. The frame is intended to protect the edges of the specimen from irradiation but covers the edges with only a few mm. In tests with products such as composite laminates and sandwich wall panels, the production of pyrolysis gases from the edges and, in many cases, burning have been observed. Early contribution from the edges in the test is not representative for surface burning. A modified specimen holder was developed with a larger specimen size to allow better protection of the edges. The opening for exposure to irradiance of the retainer frame is circular and of the same area as that of the original frame. The distance between the exposed surface and the specimen edges is larger in order to prevent early exposure of edges. Tests using the standard specimen holder resulted in pyrolysis and burning from edges that took place outside of the specimen holder. Comparative tests using the modified specimen holder showed that it prevented the exposure and pyrolysis from edges for an extended time. However, the influence on ignition time and peak heat release due to the increased size of the modified specimen holder has not been characterized fully, and test results should not be used for direct comparison with those of the standard holder.
- 16 February 2021
- Published by Wiley in Fire and Materials
- Vol. 46 (1) , 80-94
A modified specimen holder for cone calorimeter testing of composite materials to reduce influence from specimen edges
SUMMARY: ISO 5660‐1 specifies the cone calorimeter method for characterizing the ignition and surface burning behavior of materials. The specimen is irradiated through a square opening in the frame of the specimen holder. The frame is intended to protect the edges of the specimen from irradiation but covers the edges with only a few mm. In tests with products such as composite laminates and sandwich wall panels, the production of pyrolysis gases from the edges and, in many cases, burning have been observed. Early contribution from the edges in the test is not representative for surface burning. A modified specimen holder was developed with a larger specimen size to allow better protection of the edges. The opening for exposure to irradiance of the retainer frame is circular and of the same area as that of the original frame. The distance between the exposed surface and the specimen edges is larger in order to prevent early exposure of edges. Tests using the standard specimen holder resulted in pyrolysis and burning from edges that took place outside of the specimen holder. Comparative tests using the modified specimen holder showed that it prevented the exposure and pyrolysis from edges for an extended time. However, the influence on ignition time and peak heat release due to the increased size of the modified specimen holder has not been characterized fully, and test results should not be used for direct comparison with those of the standard holder.
- Open Access
Carbon, Glass and Basalt Fiber Reinforced Polybenzoxazine: The Effects of Fiber Reinforcement on Mechanical, Fire, Smoke and Toxicity Properties
Bisphenol F and aniline-based benzoxazine monomers were selected to fabricate basalt, glass and carbon fiber reinforced polybenzoxazine via vacuum infusion, respectively. The impacts of the type of fiber reinforcement on the resulting material properties of the fiber reinforced polymers (FRPs) were studied. FRPs exhibited a homogenous morphology with completely impregnated fibers and near-zero porosity. Carbon fiber reinforced polybenzoxazine showed the highest specific mechanical properties because of its low density and high modulus and strength. However, regarding the flammability, fire, smoke and toxicity properties, glass and basalt reinforced polybenzoxazine outperformed carbon fiber reinforced polybenzoxazine. This work offers a deeper understanding of how different types of fiber reinforcement affect polybenzoxazine-based FRPs and provides access to FRPs with inherently good fire, smoke and toxicity performance without the need for further flame retardant additives.
Open AccessCarbon, Glass and Basalt Fiber Reinforced Polybenzoxazine: The Effects of Fiber Reinforcement on Mechanical, Fire, Smoke and Toxicity Properties
Bisphenol F and aniline-based benzoxazine monomers were selected to fabricate basalt, glass and carbon fiber reinforced polybenzoxazine via vacuum infusion, respectively. The impacts of the type of fiber reinforcement on the resulting material properties of the fiber reinforced polymers (FRPs) were studied. FRPs exhibited a homogenous morphology with completely impregnated fibers and near-zero porosity. Carbon fiber reinforced polybenzoxazine showed the highest specific mechanical properties because of its low density and high modulus and strength. However, regarding the flammability, fire, smoke and toxicity properties, glass and basalt reinforced polybenzoxazine outperformed carbon fiber reinforced polybenzoxazine. This work offers a deeper understanding of how different types of fiber reinforcement affect polybenzoxazine-based FRPs and provides access to FRPs with inherently good fire, smoke and toxicity performance without the need for further flame retardant additives.