Oleh Kozyr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oleh Kozyr has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Zygmunt Lech Warsza
Polish Metrological Society
4 shared publications - Ihor Bohachev
General Energy Institute of NAS of Ukraine
3 shared publications - Stanislav Sozonov
General Energy Institute of NAS of Ukraine
3 shared publications - Evgeniy Volodarsky
Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського
2 shared publications - Andrii Momot
National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute», Kyiv, Ukraine
1 shared publication - Artur Zaporozhets
General Energy Institute of National Academy of Sciences of Ukraine, Kyiv, Ukraine; International Institute for Applied Systems Analysis, Laxenburg, Austria, Ukraine
1 shared publication
Latest Publications
- 22 June 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Pomiary Automatyka Robotyka
- Vol. 30 (2) , 61-67
Probability of Detecting a Constant Offset of the Mean Value of a Process Controlled by Shewhart Cards
The paper estimates the probability P with which the graphs of Shewhart control cards will signal a constant change in the position of the mean value of the parameter of the process controlled by these cards caused by non-random influences, e.g. due to the constant systematic error of the measurement system. An analytical expression describing this probability was determined. It is confirmed by modelling the shift value of the mean in the statistical experiment. The probabilities of P were obtained for the following changes in the mean value position of card points of the controlled parameter: P(σ) = 0.02, P(2σ) = 0.16 and P(3σ) = 0.5. On the other hand, the conducted studies have shown that by using a moving average, you can achieve a much higher probability of detecting a constant shift of meane value. For example, constant offset 0.5σ of 20 consecutive points has for their mean value almost 10 times larger probability to discover, and for an offset of 1σ – almost 40 times.
- 22 June 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Pomiary Automatyka Robotyka
- Vol. 30 (2) , 61-67
Probability of Detecting a Constant Offset of the Mean Value of a Process Controlled by Shewhart Cards
The paper estimates the probability P with which the graphs of Shewhart control cards will signal a constant change in the position of the mean value of the parameter of the process controlled by these cards caused by non-random influences, e.g. due to the constant systematic error of the measurement system. An analytical expression describing this probability was determined. It is confirmed by modelling the shift value of the mean in the statistical experiment. The probabilities of P were obtained for the following changes in the mean value position of card points of the controlled parameter: P(σ) = 0.02, P(2σ) = 0.16 and P(3σ) = 0.5. On the other hand, the conducted studies have shown that by using a moving average, you can achieve a much higher probability of detecting a constant shift of meane value. For example, constant offset 0.5σ of 20 consecutive points has for their mean value almost 10 times larger probability to discover, and for an offset of 1σ – almost 40 times.
- Open Access
- 24 November 2025
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Innovative Biosystems and Bioengineering
- Vol. 9 (4) , 28-45
Comparative Assessment of Cytotoxicity of Aliphatic Amino Carboxylic Compounds as Potential Anticoronavirus Agents
Background. Despite the success in creating vaccines against SARS-CoV-2, the high mutagenicity of coronaviruses, interspecies transmission, and the emergence of new strains require further search for effective antiviral agents. A key step in this process is to evaluate the cytotoxicity of potential compounds to determine their safety and therapeutic potential. Modern IT solutions, such as automated image analysis and artificial intelligence, increase the accuracy and objectivity of assessments. Objective. To determine the cytotoxicity of compounds with potential anticoronavirus activity and to analyze it using IT tools. Methods. The study used the grafting cell line BHK-21 of the gerbil hamster, which was incubated with seven aliphatic amino carbon compounds in six concentrations. Cell viability was determined using the MTT assay. Cell monolayer image processing and an exponential dose-response model were used for automated analysis. Results. The study revealed a pronounced dose- and time-dependent cytotoxicity of most samples, with a maximum decrease in viability at concentrations above 10 mg/ml. The hormesis effect was recorded at low concentrations (up to 5-10 mg/ml), which may indicate the activation of cellular defense mechanisms. The high correlation between measurements at 492 nm and 550 nm (R² > 0.98) confirmed the reliability of the spectrophotometric data. The exponential model allowed us to approximate the toxicity curves, especially in the middle and high concentration ranges. The built neural network based on image data and MTT test showed the ability to predict cell viability even with a limited amount of training data. Conclusions. The combination of the MTT assay with automated image analysis provides a comprehensive assessment of cytotoxicity. A dose-dependent decrease in cell viability and morphological changes under the influence of the studied compounds were found. Measurements at 550 nm proved to be more sensitive to early changes in cell metabolism. The use of IT algorithms has demonstrated the prospects of an automated approach to the screening of biologically active substances.
- 24 November 2025
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Innovative Biosystems and Bioengineering
- Vol. 9 (4) , 28-45
Open AccessComparative Assessment of Cytotoxicity of Aliphatic Amino Carboxylic Compounds as Potential Anticoronavirus Agents
Background. Despite the success in creating vaccines against SARS-CoV-2, the high mutagenicity of coronaviruses, interspecies transmission, and the emergence of new strains require further search for effective antiviral agents. A key step in this process is to evaluate the cytotoxicity of potential compounds to determine their safety and therapeutic potential. Modern IT solutions, such as automated image analysis and artificial intelligence, increase the accuracy and objectivity of assessments. Objective. To determine the cytotoxicity of compounds with potential anticoronavirus activity and to analyze it using IT tools. Methods. The study used the grafting cell line BHK-21 of the gerbil hamster, which was incubated with seven aliphatic amino carbon compounds in six concentrations. Cell viability was determined using the MTT assay. Cell monolayer image processing and an exponential dose-response model were used for automated analysis. Results. The study revealed a pronounced dose- and time-dependent cytotoxicity of most samples, with a maximum decrease in viability at concentrations above 10 mg/ml. The hormesis effect was recorded at low concentrations (up to 5-10 mg/ml), which may indicate the activation of cellular defense mechanisms. The high correlation between measurements at 492 nm and 550 nm (R² > 0.98) confirmed the reliability of the spectrophotometric data. The exponential model allowed us to approximate the toxicity curves, especially in the middle and high concentration ranges. The built neural network based on image data and MTT test showed the ability to predict cell viability even with a limited amount of training data. Conclusions. The combination of the MTT assay with automated image analysis provides a comprehensive assessment of cytotoxicity. A dose-dependent decrease in cell viability and morphological changes under the influence of the studied compounds were found. Measurements at 550 nm proved to be more sensitive to early changes in cell metabolism. The use of IT algorithms has demonstrated the prospects of an automated approach to the screening of biologically active substances.
- 1 October 2025
- Published by Springer Nature
- p. 235-246
Virtual Device for Analysis of Measurement Data by Magnetostrictive Method
- 1 October 2025
- Published by Springer Nature
- p. 235-246
Virtual Device for Analysis of Measurement Data by Magnetostrictive Method
- Open Access
- 21 July 2025
- Published by Kharkiv National University of Radioelectronics in Metrology and instruments
- No. 1,p. 03
Statistical assessment of the reliability of decisions on the state of controlled technological process based on E. Volodarskyi approach
The article concerns the issues of using control charts to study the parameters describing the state of the productsin their production process. The identification of reliability of a decision is based on the assessment of disturbances occurring in it is discussed.Using is the method proposed by † Yevhen Volodarskyi1, that was based on Bayesian approach. The influence of measurement errors and their distribution of probability on the correctness of the decisions taken is considered. In the article two estimations of conformity of technological process to the norms based on the results of its control are considered. The first assessment is a-priori probability or reliability of the control result, which is performed before the control procedure and is based on a-priori data about the process and measurement error. The paper proposes the use of the second assessment, namely the posterior probability of compliance of the technological process with the norms. This assessment of compliance is performed after the control result is obtained, when only half of the set of elementary events contributing to the occurrence of one of the control results is left for evaluation. The use of this estimation allows doubling the statistical reliability of the control result estimation. The effectiveness of assessing the compliance of the technological process with the standards established for the uniform distribution of the values of its controlled parameters and their measurement errors is also determined.
- 21 July 2025
- Published by Kharkiv National University of Radioelectronics in Metrology and instruments
- No. 1,p. 03
Open AccessStatistical assessment of the reliability of decisions on the state of controlled technological process based on E. Volodarskyi approach
The article concerns the issues of using control charts to study the parameters describing the state of the productsin their production process. The identification of reliability of a decision is based on the assessment of disturbances occurring in it is discussed.Using is the method proposed by † Yevhen Volodarskyi1, that was based on Bayesian approach. The influence of measurement errors and their distribution of probability on the correctness of the decisions taken is considered. In the article two estimations of conformity of technological process to the norms based on the results of its control are considered. The first assessment is a-priori probability or reliability of the control result, which is performed before the control procedure and is based on a-priori data about the process and measurement error. The paper proposes the use of the second assessment, namely the posterior probability of compliance of the technological process with the norms. This assessment of compliance is performed after the control result is obtained, when only half of the set of elementary events contributing to the occurrence of one of the control results is left for evaluation. The use of this estimation allows doubling the statistical reliability of the control result estimation. The effectiveness of assessing the compliance of the technological process with the standards established for the uniform distribution of the values of its controlled parameters and their measurement errors is also determined.
- 3 July 2025
- Published by Springer Nature
- p. 205-225
Impulse Start Detection Algorithm to Automate Magnetostrictive Sensor Data Analysis for Quality Control Devices
- 3 July 2025
- Published by Springer Nature
- p. 205-225
Impulse Start Detection Algorithm to Automate Magnetostrictive Sensor Data Analysis for Quality Control Devices
- Open Access
- 31 March 2025
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 15 (1) , 5-9
Statistical reliability of decisions on controlled process faults
The article considers the issues of using control charts to detect the disruption of the technological process. The possible influence of measurement error on the correctness of decisions is considered. To ensure the statistical reliability of the decisions made, their plausibility, a priori probability is used. The effectiveness of assessing the compliance of the technological process with established standards is discussed, when the distributions of possible values of its parameters and errors of their measurements are uniform.
- 31 March 2025
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 15 (1) , 5-9
Open AccessStatistical reliability of decisions on controlled process faults
The article considers the issues of using control charts to detect the disruption of the technological process. The possible influence of measurement error on the correctness of decisions is considered. To ensure the statistical reliability of the decisions made, their plausibility, a priori probability is used. The effectiveness of assessing the compliance of the technological process with established standards is discussed, when the distributions of possible values of its parameters and errors of their measurements are uniform.
- Open Access
- 27 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2025 (1) , 85-99
REDUCING THE INFLUENCE OF NOISE ON THE ACCURACY OF ULTRASONIC PULSE ONSET DETECTION
An essential component of ultrasonic nondestructive testing is determining the delay time between the transmitted and received signals. Therefore, the accuracy of determining the onset of both the transmitted and received pulse affects the accuracy of all subsequent calculations. The main measuring transducers are usually piezoelectric. A relatively new approach involves using small-aperture magnetostrictive transducers as a generator and receiver of the ultrasonic signal. Such magnetostrictive sensors have low-current excitation coils, resulting in low amplitudes of received signals. Therefore, it is an urgent task to develop algorithms for determining the onset of a pulse that could reduce the noise present in the signal or not be sensitive to it. In this paper, a method for determining the onset of an ultrasonic pulse is proposed based on utilizing a standard function from the LabVIEW library to determine the position of the peak value of a periodic pulse. The mathematical expressions for modeling transmitted and received pulses were obtained. Based on these mathematical expressions, a modeling experiment was conducted to verify the accuracy of determining the beginning of the probing pulse by the proposed method. The simulation experiment was performed with noise following a Gaussian distribution for the range of standard deviation (SD) values from 0 to 10. According to the modeling results, it was found that the proposed method allows determining the beginning of the probing pulse with a relative error not exceeding 3.5 % for the values of the SWR less than 2. Keywords: ultrasonic signal, magnetostrictive sensor, signal-to-noise ratio.
- 27 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2025 (1) , 85-99
Open AccessREDUCING THE INFLUENCE OF NOISE ON THE ACCURACY OF ULTRASONIC PULSE ONSET DETECTION
An essential component of ultrasonic nondestructive testing is determining the delay time between the transmitted and received signals. Therefore, the accuracy of determining the onset of both the transmitted and received pulse affects the accuracy of all subsequent calculations. The main measuring transducers are usually piezoelectric. A relatively new approach involves using small-aperture magnetostrictive transducers as a generator and receiver of the ultrasonic signal. Such magnetostrictive sensors have low-current excitation coils, resulting in low amplitudes of received signals. Therefore, it is an urgent task to develop algorithms for determining the onset of a pulse that could reduce the noise present in the signal or not be sensitive to it. In this paper, a method for determining the onset of an ultrasonic pulse is proposed based on utilizing a standard function from the LabVIEW library to determine the position of the peak value of a periodic pulse. The mathematical expressions for modeling transmitted and received pulses were obtained. Based on these mathematical expressions, a modeling experiment was conducted to verify the accuracy of determining the beginning of the probing pulse by the proposed method. The simulation experiment was performed with noise following a Gaussian distribution for the range of standard deviation (SD) values from 0 to 10. According to the modeling results, it was found that the proposed method allows determining the beginning of the probing pulse with a relative error not exceeding 3.5 % for the values of the SWR less than 2. Keywords: ultrasonic signal, magnetostrictive sensor, signal-to-noise ratio.
- Open Access
- 29 November 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2024 (4) , 77-87
CONTROL CHARTS FOR CORRELATED PROCESS PARAMETERS
An urgent practical task is to ensure the serviceability and safety of complex technical and information systems by monitoring their current states. Additionally, an important task is to use control charts to automatically detect the moment when certain limit states are exceeded by the characteristic features (parameters) of the technological process. In practice, it is quite common for characteristic features to be correlated. The presence of correlation affects the effectiveness of control charts in determining the moment of process disruption. The study objective is to compare the effectiveness of using different control chart types to control a correlated parameter process. The following control charts were studied: Shewhart, Hotelling, and modified Shewhart charts − principal component charts. Numerical modeling of a two-parameter process was conducted with the introduction of a non-random change in one of them at two control points, i.e., the process disorder was modeled at the appropriate time points. Subsequently, statistical studies of the modeled process were conducted using three types of control charts. The results revealed that the Shewhart charts did not reveal any process disruption, which is explained by the correlation of the parameters. Hotelling charts revealed a processing disorder at two points, but they do not indicate the cause of the disorder. The calculated partial Hotelling criterion did not indicate the cause of the disorder. The principal component charts revealed both the presence of a process disorder in two points and identified which parameter caused the disorder. This result demonstrates the effectiveness of principal component charts in detecting process disorder with correlated parameters, as well as their superiority over other charts that were studied. In addition, with an increase in the number of parameters, this method becomes even more effective, as it allows to reduce the number of parameters studied while maintaining their statistical significance. Keywords: effectiveness of control charts, Shewhart charts, Hotelling charts, principal components, statistical quality control, correlation of parameters.
- 29 November 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2024 (4) , 77-87
Open AccessCONTROL CHARTS FOR CORRELATED PROCESS PARAMETERS
An urgent practical task is to ensure the serviceability and safety of complex technical and information systems by monitoring their current states. Additionally, an important task is to use control charts to automatically detect the moment when certain limit states are exceeded by the characteristic features (parameters) of the technological process. In practice, it is quite common for characteristic features to be correlated. The presence of correlation affects the effectiveness of control charts in determining the moment of process disruption. The study objective is to compare the effectiveness of using different control chart types to control a correlated parameter process. The following control charts were studied: Shewhart, Hotelling, and modified Shewhart charts − principal component charts. Numerical modeling of a two-parameter process was conducted with the introduction of a non-random change in one of them at two control points, i.e., the process disorder was modeled at the appropriate time points. Subsequently, statistical studies of the modeled process were conducted using three types of control charts. The results revealed that the Shewhart charts did not reveal any process disruption, which is explained by the correlation of the parameters. Hotelling charts revealed a processing disorder at two points, but they do not indicate the cause of the disorder. The calculated partial Hotelling criterion did not indicate the cause of the disorder. The principal component charts revealed both the presence of a process disorder in two points and identified which parameter caused the disorder. This result demonstrates the effectiveness of principal component charts in detecting process disorder with correlated parameters, as well as their superiority over other charts that were studied. In addition, with an increase in the number of parameters, this method becomes even more effective, as it allows to reduce the number of parameters studied while maintaining their statistical significance. Keywords: effectiveness of control charts, Shewhart charts, Hotelling charts, principal components, statistical quality control, correlation of parameters.
- Open Access
- 30 June 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Bulletin of Kyiv Polytechnic Institute. Series Instrument Making
- No. 67(1),p. 31-39
INDIVIDUAL CONTROL CHARTS FOR NON-NORMAL DATA
Individual control charts are a suitable option to consider when the processes being studied change slowly. If obtaining standard samples for Shewhart control charts is expensive or in the case of studying statistical characteristics of the technological process, they are used. Control charts are used to control technological processes in the case of a normal distribution of the possible values of the controlled parameter. Sometimes a quasi-normal distribution of the studied parameter is allowed. In practice, it is often necessary to deal with technological processes in which samples are not distributed according to a normal distribution. In such cases, using individual control charts can lead to type I and II errors. This is because the control limits of the charts are calculated for the mean and standard deviation of the normal distribution. Control charts of individual values are most sensitive to the deviation of the distribution from the normal one since individual values are used to construct the limits, to which the central limit theorem does not apply, as in the case of control charts of mean values. Therefore, it is extremely important to develop methods of applying the individual control charts for random samples, the general population of which is not normally distributed. The study examines the application of individual control charts for a random process that is non-normally distributed. This is achieved by using the normalization method to transform samples of the studied parameter into samples that are distributed normally or quasi-normally. The normalization is performed using the Box-Cox method with further construction of control charts based on the transformed samples. The mathematical apparatus of the individual control chart application for samples with non-normal distribution is described. Numerical modeling of the application of individual control charts for the chi-square distributed samples, which have a significant distribution asymmetry for small values of the shape factor, and for the samples obtained by normalizing the chi-square one, was performed. According to the research findings, the utilization of individual control charts for samples exhibiting a significantly asymmetric distribution results in a higher likelihood of type I errors being detected. However, when the method of sample normalization is employed, this issue is almost entirely eliminated. Modeling process disruption, by changing a certain individual value, also demonstrated the emergence of false signals of process disruption.
- 30 June 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Bulletin of Kyiv Polytechnic Institute. Series Instrument Making
- No. 67(1),p. 31-39
Open AccessINDIVIDUAL CONTROL CHARTS FOR NON-NORMAL DATA
Individual control charts are a suitable option to consider when the processes being studied change slowly. If obtaining standard samples for Shewhart control charts is expensive or in the case of studying statistical characteristics of the technological process, they are used. Control charts are used to control technological processes in the case of a normal distribution of the possible values of the controlled parameter. Sometimes a quasi-normal distribution of the studied parameter is allowed. In practice, it is often necessary to deal with technological processes in which samples are not distributed according to a normal distribution. In such cases, using individual control charts can lead to type I and II errors. This is because the control limits of the charts are calculated for the mean and standard deviation of the normal distribution. Control charts of individual values are most sensitive to the deviation of the distribution from the normal one since individual values are used to construct the limits, to which the central limit theorem does not apply, as in the case of control charts of mean values. Therefore, it is extremely important to develop methods of applying the individual control charts for random samples, the general population of which is not normally distributed. The study examines the application of individual control charts for a random process that is non-normally distributed. This is achieved by using the normalization method to transform samples of the studied parameter into samples that are distributed normally or quasi-normally. The normalization is performed using the Box-Cox method with further construction of control charts based on the transformed samples. The mathematical apparatus of the individual control chart application for samples with non-normal distribution is described. Numerical modeling of the application of individual control charts for the chi-square distributed samples, which have a significant distribution asymmetry for small values of the shape factor, and for the samples obtained by normalizing the chi-square one, was performed. According to the research findings, the utilization of individual control charts for samples exhibiting a significantly asymmetric distribution results in a higher likelihood of type I errors being detected. However, when the method of sample normalization is employed, this issue is almost entirely eliminated. Modeling process disruption, by changing a certain individual value, also demonstrated the emergence of false signals of process disruption.
- 19 September 2023
- Published by Springer Nature
- p. 17-61
Application of Exponential Splines in the Measurement and Control of Electric Circuit Parameters
- 19 September 2023
- Published by Springer Nature
- p. 17-61
Application of Exponential Splines in the Measurement and Control of Electric Circuit Parameters