Ihor Bohachev
Research Subjects
Ihor Bohachev has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Artur Zaporozhets
General Energy Institute of National Academy of Sciences of Ukraine, Kyiv, Ukraine; International Institute for Applied Systems Analysis, Laxenburg, Austria, Ukraine
5 shared publications - Stanislav Sozonov
General Energy Institute of NAS of Ukraine
4 shared publications - Oleh Kozyr
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
3 shared publications - Vitalii Babak
Department of Forecasting the Electric Power Complex Development, General Energy Institute of National Academy of Sciences of Ukraine, 03150 Kyiv, Ukraine
3 shared publications - Vladyslav Khaidurov
General Energy Institute of the National Academy of Sciences of Ukraine, 03150 Kyiv, Ukraine
3 shared publications - Anastasiia Sverdlova
Institute of General Energy of the National Academy of Sciences of Ukraine
2 shared publications
Latest Publications
- 1 October 2025
- Published by Springer Nature
- p. 235-246
Virtual Device for Analysis of Measurement Data by Magnetostrictive Method
- 1 October 2025
- Published by Springer Nature
- p. 235-246
Virtual Device for Analysis of Measurement Data by Magnetostrictive Method
- 3 July 2025
- Published by Springer Nature
- p. 205-225
Impulse Start Detection Algorithm to Automate Magnetostrictive Sensor Data Analysis for Quality Control Devices
- 3 July 2025
- Published by Springer Nature
- p. 205-225
Impulse Start Detection Algorithm to Automate Magnetostrictive Sensor Data Analysis for Quality Control Devices
- Open Access
- 27 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2025 (1) , 85-99
REDUCING THE INFLUENCE OF NOISE ON THE ACCURACY OF ULTRASONIC PULSE ONSET DETECTION
An essential component of ultrasonic nondestructive testing is determining the delay time between the transmitted and received signals. Therefore, the accuracy of determining the onset of both the transmitted and received pulse affects the accuracy of all subsequent calculations. The main measuring transducers are usually piezoelectric. A relatively new approach involves using small-aperture magnetostrictive transducers as a generator and receiver of the ultrasonic signal. Such magnetostrictive sensors have low-current excitation coils, resulting in low amplitudes of received signals. Therefore, it is an urgent task to develop algorithms for determining the onset of a pulse that could reduce the noise present in the signal or not be sensitive to it. In this paper, a method for determining the onset of an ultrasonic pulse is proposed based on utilizing a standard function from the LabVIEW library to determine the position of the peak value of a periodic pulse. The mathematical expressions for modeling transmitted and received pulses were obtained. Based on these mathematical expressions, a modeling experiment was conducted to verify the accuracy of determining the beginning of the probing pulse by the proposed method. The simulation experiment was performed with noise following a Gaussian distribution for the range of standard deviation (SD) values from 0 to 10. According to the modeling results, it was found that the proposed method allows determining the beginning of the probing pulse with a relative error not exceeding 3.5 % for the values of the SWR less than 2. Keywords: ultrasonic signal, magnetostrictive sensor, signal-to-noise ratio.
- 27 February 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2025 (1) , 85-99
Open AccessREDUCING THE INFLUENCE OF NOISE ON THE ACCURACY OF ULTRASONIC PULSE ONSET DETECTION
An essential component of ultrasonic nondestructive testing is determining the delay time between the transmitted and received signals. Therefore, the accuracy of determining the onset of both the transmitted and received pulse affects the accuracy of all subsequent calculations. The main measuring transducers are usually piezoelectric. A relatively new approach involves using small-aperture magnetostrictive transducers as a generator and receiver of the ultrasonic signal. Such magnetostrictive sensors have low-current excitation coils, resulting in low amplitudes of received signals. Therefore, it is an urgent task to develop algorithms for determining the onset of a pulse that could reduce the noise present in the signal or not be sensitive to it. In this paper, a method for determining the onset of an ultrasonic pulse is proposed based on utilizing a standard function from the LabVIEW library to determine the position of the peak value of a periodic pulse. The mathematical expressions for modeling transmitted and received pulses were obtained. Based on these mathematical expressions, a modeling experiment was conducted to verify the accuracy of determining the beginning of the probing pulse by the proposed method. The simulation experiment was performed with noise following a Gaussian distribution for the range of standard deviation (SD) values from 0 to 10. According to the modeling results, it was found that the proposed method allows determining the beginning of the probing pulse with a relative error not exceeding 3.5 % for the values of the SWR less than 2. Keywords: ultrasonic signal, magnetostrictive sensor, signal-to-noise ratio.
- Open Access
- 9 June 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2023 (2) , 72-82
Enhanced phase method of signal detection for ultrasonic magnetostriction defectoscopy of power equipment
The magnetostrictive method of ultrasonic flaw detection has certain advantages, in particular, the ability to control objects with complex geometry, at their high temperature, the ability to control dry contact between the transducer and the object, difficult access to the controlled area, etc. The peculiarities of the generation of ultrasonic waves by magnetostrictive transducers and their distribution in control objects determine the low level of the signal/noise ratio, which limits the possibilities of practical application of this method. The aim of the paper is to improve the phase method for detecting signals of magnetostrictive receivers with a low signal/noise ratio and to check the effectiveness of the proposed technical solution for solving problems of non-destructive testing of energy equipment elements using magnetostrictive defectoscopes. The paper discusses the phase method of detecting radio pulse signals of magnetostrictive converters against the background of additive noise, which is based on a combination of the capabilities of the discrete Hilbert transformation, which makes it possible to determine the envelope and phase of signals, and methods of statistical processing of the results of phase measurements. The proposed signal processing algorithm was studied both in a model experiment and when processing real magnetostrictive defectoscope signals. The proposed method makes it possible to detect radio pulse signals with a signal/noise ratio close to 1. The reliability of the obtained data is confirmed by the results of computer simulation. The considered method of detecting signals can be used in ultrasonic magnetostrictive defectoscopes and other diagnostic systems operating in conditions of reduced signal/noise ratio. Keywords: magnetostrictive defectoscope, ultrasonic defectoscopy, phase methods of signal processing, Hilbert transform, envelope, phase, sample resulting length of the vector.
- 9 June 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in System Research in Energy
- Vol. 2023 (2) , 72-82
Open AccessEnhanced phase method of signal detection for ultrasonic magnetostriction defectoscopy of power equipment
The magnetostrictive method of ultrasonic flaw detection has certain advantages, in particular, the ability to control objects with complex geometry, at their high temperature, the ability to control dry contact between the transducer and the object, difficult access to the controlled area, etc. The peculiarities of the generation of ultrasonic waves by magnetostrictive transducers and their distribution in control objects determine the low level of the signal/noise ratio, which limits the possibilities of practical application of this method. The aim of the paper is to improve the phase method for detecting signals of magnetostrictive receivers with a low signal/noise ratio and to check the effectiveness of the proposed technical solution for solving problems of non-destructive testing of energy equipment elements using magnetostrictive defectoscopes. The paper discusses the phase method of detecting radio pulse signals of magnetostrictive converters against the background of additive noise, which is based on a combination of the capabilities of the discrete Hilbert transformation, which makes it possible to determine the envelope and phase of signals, and methods of statistical processing of the results of phase measurements. The proposed signal processing algorithm was studied both in a model experiment and when processing real magnetostrictive defectoscope signals. The proposed method makes it possible to detect radio pulse signals with a signal/noise ratio close to 1. The reliability of the obtained data is confirmed by the results of computer simulation. The considered method of detecting signals can be used in ultrasonic magnetostrictive defectoscopes and other diagnostic systems operating in conditions of reduced signal/noise ratio. Keywords: magnetostrictive defectoscope, ultrasonic defectoscopy, phase methods of signal processing, Hilbert transform, envelope, phase, sample resulting length of the vector.
- 2 March 2023
- Published by Springer Nature
- p. 63-92
Mathematical Models and Software for Studying the Elasticity of Building Structures and Their Systems
- 2 March 2023
- Published by Springer Nature
- p. 63-92
Mathematical Models and Software for Studying the Elasticity of Building Structures and Their Systems
- Open Access
- 17 January 2023
- Published by MDPI AG in Electronics
- Vol. 12 (3) , 477
Some Features of Modeling Ultrasound Propagation in Non-Destructive Control of Metal Structures Based on the Magnetostrictive Effect
A method and mathematical models of direct and inverse problems of ultrasonic testing and diagnostics of complex metal structures for defects were developed and tested. A prototype of a system for magnetostrictive control of elements of the objects under study was manufactured and experimentally tested. Mathematical simulation of ultrasonic testing processes using MATLAB and the COMSOL Multiphysics software environment was carried out. The adequacy of the mathematical models was verified by the results of their comparison with real physical experiments. Information support and a methodology that implements it was developed, which ensure the functioning of the control facilities for these objects based on the use of small-aperture magnetostrictive transducers. The mathematical identification of the vibration generator in complex building structures was developed, which consists in finding the locations of the generator of ultrasonic vibrations, as well as the characteristics of this vibration generator based on data obtained from sensors in the form of time series.
- 17 January 2023
- Published by MDPI AG in Electronics
- Vol. 12 (3) , 477
Open AccessSome Features of Modeling Ultrasound Propagation in Non-Destructive Control of Metal Structures Based on the Magnetostrictive Effect
A method and mathematical models of direct and inverse problems of ultrasonic testing and diagnostics of complex metal structures for defects were developed and tested. A prototype of a system for magnetostrictive control of elements of the objects under study was manufactured and experimentally tested. Mathematical simulation of ultrasonic testing processes using MATLAB and the COMSOL Multiphysics software environment was carried out. The adequacy of the mathematical models was verified by the results of their comparison with real physical experiments. Information support and a methodology that implements it was developed, which ensure the functioning of the control facilities for these objects based on the use of small-aperture magnetostrictive transducers. The mathematical identification of the vibration generator in complex building structures was developed, which consists in finding the locations of the generator of ultrasonic vibrations, as well as the characteristics of this vibration generator based on data obtained from sensors in the form of time series.
- Open Access
- 21 November 2022
- Published by Academy of Cognitive and Natural Sciences in Journal of Edge Computing
- Vol. 1 (1) , 29-42
Dynamic routing protocols for wireless touch networks: a review
This article has been retracted. Please see: Retraction of published article due to the author’s proposal - 23 March 2023 Wireless Touch Networks (WTN) have become increasingly important with the emergence of the Internet of Things (IoT) and are regarded as a class of self-organizing networks. This article presents an overview of the construction principles, routing protocols, quality of service parameters, traffic models, and characteristics of WTN. The article also explores the application of dynamic routing protocols for constructing a self-organizing network of autonomous IoT systems. Known dynamic routing protocols for mobile radio networks are reviewed and the advantages and disadvantages of proactive and reactive approaches are discussed.
- 21 November 2022
- Published by Academy of Cognitive and Natural Sciences in Journal of Edge Computing
- Vol. 1 (1) , 29-42
Open AccessDynamic routing protocols for wireless touch networks: a review
This article has been retracted. Please see: Retraction of published article due to the author’s proposal - 23 March 2023 Wireless Touch Networks (WTN) have become increasingly important with the emergence of the Internet of Things (IoT) and are regarded as a class of self-organizing networks. This article presents an overview of the construction principles, routing protocols, quality of service parameters, traffic models, and characteristics of WTN. The article also explores the application of dynamic routing protocols for constructing a self-organizing network of autonomous IoT systems. Known dynamic routing protocols for mobile radio networks are reviewed and the advantages and disadvantages of proactive and reactive approaches are discussed.
- Open Access
- 23 May 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2022 (3) , 69-78
NOVEL SMALL-APERTURE TRANSDUCERS BASED ON MAGNETOSTRICTIVE EFFECT FOR DIAGNOSTIC SYSTEMS
Small-aperture transducers based on the magnetostrictive effect for the emission and reception of signals in the ultrasonic range in solid materials have been developed. The article discusses their design features and specifications. Attention is paid to the features of the choice of materials, shapes, and geometrical dimensions of the excitation coil, damper, and magnet. Structural and electrical circuits of the developed transducers are given. Some design and technological solutions have been proposed that can increase the radiation power by 10 times, and resolution by 2-3 times, compared with existing analogs. The area of the radiating part of the sensor is from 0.07 to 0.2 mm2. Such transducers can be used in various diagnostic systems to detect defects in power equipment, aircraft products, industrial equipment, etc. References 22, figures 10, tables 4.
- 23 May 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2022 (3) , 69-78
Open AccessNOVEL SMALL-APERTURE TRANSDUCERS BASED ON MAGNETOSTRICTIVE EFFECT FOR DIAGNOSTIC SYSTEMS
Small-aperture transducers based on the magnetostrictive effect for the emission and reception of signals in the ultrasonic range in solid materials have been developed. The article discusses their design features and specifications. Attention is paid to the features of the choice of materials, shapes, and geometrical dimensions of the excitation coil, damper, and magnet. Structural and electrical circuits of the developed transducers are given. Some design and technological solutions have been proposed that can increase the radiation power by 10 times, and resolution by 2-3 times, compared with existing analogs. The area of the radiating part of the sensor is from 0.07 to 0.2 mm2. Such transducers can be used in various diagnostic systems to detect defects in power equipment, aircraft products, industrial equipment, etc. References 22, figures 10, tables 4.
- 19 April 2021
- Published by Academy of Cognitive and Natural Sciences
Self-organizing network topology for autonomous IoT systems
The concept of the Internet of Things is increasingly defining the development of communication net- works both now and in the future. The largest application of the IoT concept is wireless touch networks (WTN). Due to the potentially widespread use of WTN in all areas of human life, they are also called pervasive sensory networks. WTN belongs to the class of self-organizing networks, for which the con- struction principles, routing protocols, quality of service parameters, traffic models, and characteristics are significantly modified compared to traditional infrastructure networks, etc. The features of the ap- plication of dynamic routing protocols for the construction of a self-organizing network of autonomous IoT systems are considered. This article provides an overview of the main methods for calculating the topology of self-organizing networks. A review of known dynamic routing protocols for mobile radio networks is given, the advantages and disadvantages of proactive and reactive approaches are shown.
- 19 April 2021
- Published by Academy of Cognitive and Natural Sciences
Self-organizing network topology for autonomous IoT systems
The concept of the Internet of Things is increasingly defining the development of communication net- works both now and in the future. The largest application of the IoT concept is wireless touch networks (WTN). Due to the potentially widespread use of WTN in all areas of human life, they are also called pervasive sensory networks. WTN belongs to the class of self-organizing networks, for which the con- struction principles, routing protocols, quality of service parameters, traffic models, and characteristics are significantly modified compared to traditional infrastructure networks, etc. The features of the ap- plication of dynamic routing protocols for the construction of a self-organizing network of autonomous IoT systems are considered. This article provides an overview of the main methods for calculating the topology of self-organizing networks. A review of known dynamic routing protocols for mobile radio networks is given, the advantages and disadvantages of proactive and reactive approaches are shown.