YZYongtao Zhao

Yongtao Zhao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yongtao Zhao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Hierarchical Control Scheme for Adaptive Cruise Control System Based on Model Predictive Control

    by Hongyuan Mu, Liang Li, Mingming Mei, Yongtao Zhao

    An adaptive cruise control (ACC) system can improve safety and comfort during driving by taking over longitudinal control of the vehicle. It requires the coordination between the upper-layer controller and the lower-layer actuators. In this paper, a hierarchical anti-disturbance cruise control architecture based on electronic stability control (ESC) system is proposed. The upper-layer controller outputs the desired longitudinal acceleration or deceleration to the lower-layer actuators. In order to improve the accuracy of model prediction and achieve the coordinated control of multiple objectives, an upper-layer model prediction cruise controller is established based on feedback control and disturbance compensation. In addition, based on the hydraulic control unit (HCU) model and the vehicle longitudinal dynamics model, a lower-layer nonlinear model predictive deceleration controller is proposed in order to solve the problems of pressure fluctuations and the low accuracy of small decelerations when ESC is used as the actuator for the ACC system. Finally, the simulation and experimental tests were carried out. The results show that the proposed control architecture can improve the stability and comfort of the cruise control process. Moreover, compared with the traditional PID deceleration controller, it effectively improves the deceleration control accuracy.


  • Open Access

    An autonomous emergency braking strategy based on non‐linear model predictive deceleration control

    by Hongyuan Mu, Zebin Li, Guozheng Sun, Liang Li, Yongtao Zhao, Mingming Mei

    Surrogate safety measures (SSM) are used to assess the risk for autonomous emergency braking system (AEBS). Developing appropriate SSM and accurately executing the braking request are the key issues. Time‐to‐collision (TTC) is a typical time‐based SSM with limitations. By analyzing the braking process, this paper proposes a new SSM based on deceleration rate to avoid collision (DRAC). As the brake actuator, vehicle electronic stability control (ESC) system has many problems, such as large overshoot and pressure fluctuation. Considering the model of hydraulic control unit (HCU) and vehicle, a deceleration controller based on non‐linear model predictive control (NMPC) is proposed. Based on this, a layered AEBS architecture is proposed. The upper‐layer AEBS controller calculates the expected deceleration based on modified DRAC (MDRAC), and transmits it to the lower‐layer NMPC deceleration controller. Finally, the simulation and experimental tests are carried out. The results show that the system has a fast and stable response. In addition, the performance of the proposed AEBS strategy is tested according to the Euro‐NCAP test protocol. Comparing the results with the TTC method, the proposed method can improve the stability of the distance margin by more than 0.55 m, which ensures the safety and improves the stability of the vehicle.


  • Research on accurate modeling and control for pneumatic electric braking system of commercial vehicle based on multi-dynamic parameters measurement

    by Yongtao Zhao, Yiyong Yang, Xiuheng Wu, Xingjun Tao

    Accurate pressure control and fast dynamic response are vital to the pneumatic electric braking system (PEBS) for those commercial vehicles that require higher regulation precision of braking force on four wheels when braking force distribution is carried out under some conditions. Due to the lagging information acquisition, most feedback-based control algorithms are difficult to further improve the dynamic response of PEBS. Meanwhile, feedforward-based control algorithms like predictive control perform well in improving dynamic performance but because of the large amount of computation and complexity of this kind of control algorithm, it cannot be applied in real-time on the single-chip microcomputer, and it is still in the stage of theoretical research at present. To address this issue and for the sake of engineering reliability, this article presents a logic threshold control scheme combining analogous model predictive control (AMPC) and proportional control. In addition, an experimental device for real-time measuring PEBS multi-dynamic parameters is built. After correcting the key parameters, the precise model is determined and the influence of switching solenoid valve on its dynamic response characteristics is studied. For the control scheme, numerical and physical validation is executed to demonstrate the feasibility of the strategy and for the performance of the controller design. The experimental results show that the dynamic model of PEBS can accurately reflect its pressure characteristics. Furthermore, under different air source pressures, the designed controller can stably control the pressure output of PEBS and ensure that the error is within 0.08 bar. Compared with the traditional control algorithm, the rapidity is improved by 32.5%.


  • Open Access

    Pressure control for pneumatic electric braking system of commercial vehicle based on model predictive control

    by Yongtao Zhao, Yiyong Yang

    Precise braking pressure control of a pneumatic electric braking system (PEBS) poses challenging non‐linear control problems, since it can operate in several distinct discrete processes (the pressure increasing, holding and decreasing) by switching the on‐off solenoid valves and the piston of relay valve moves irregularly. This article describes the development and experimental validation of a viable controller for an electronically controlled braking pressure based on the theory of model predictive control (MPC). The controller design consists of two parts. The non‐linear characteristic is first studied to ensure the pressure response of PEBS when the opening time is 4–10 ms in a fixed period, followed by calculation and prediction of the optimal on‐off time of inlet valve and release valve based on the current braking pressure to realize steady state. A logic rule is designed to ensure that the MPC controller and feedback control work coordinate to guarantee engineering reliability. A comprehensive system model is derived to help characterize system non‐linearities and design the MPC predictive model. Simulations and experimental results are presented finally to show how the MPC and feedback control strategy can be successfully applied to solve the braking pressure control of a PEBS in a systematic way.


  • Open Access

    Research on Accurate Modeling and Control for Pneumatic Electric Braking System of Commercial Vehicle Based on Multi-Dynamic Parameters Measurement

    by Yongtao Zhao, Yiyong Yang, Xiuheng Wu, Xingjun Tao

    Accurate pressure control and fast dynamic response are vital to the pneumatic electric braking system (PEBS) for that commercial vehicles require higher regulation precision of braking force on four wheels when braking force distribution is carried out under some conditions. Due to the lagging information acquisition, most feedback-based control algorithms are difficult to further improve the dynamic response of PEBS. Meanwhile, feedforward-based control algorithms like predictive control perform well in improving dynamic performance. but because of the large amount of computation and complexity of this kind of control algorithm, it cannot be applied in real-time on single-chip microcomputer, and it is still in the stage of theoretical research at present. To address this issue and for the sake of engineering reliability, this article presents a logic threshold control scheme combining analogous model predictive control (AMPC) and proportional control. In addition, an experimental device for real-time measuring PEBS multi-dynamic parameters is built. After correcting the key parameters, the precise model is determined and the influence of switching solenoid valve on its dynamic response characteristics is studied. For the control scheme, numerical and physical validation are executed to demonstrate the feasibility of the strategy and for the performance of the controller design. The experimental results show that the dynamic model of PEBS can accurately reflect its pressure characteristics. Furthermore, under different air source pressures, the designed controller can stably control the pressure output of PEBS and ensure that the error is within 8KPa. Compared with the traditional control algorithm, the rapidity is improved by 32.5%.