Hongyuan Mu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hongyuan Mu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Liang Li
Tsinghua University
3 shared publications - Mingming Mei
State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084, China
2 shared publications - Shuo Cheng
Beihang University
2 shared publications - Yongtao Zhao
School of Engineering and Technology, China University of Geosciences, Beijing 100083, China
2 shared publications Guozheng Sun
Department of Intelligent Software Center Dongfeng Motor Corporation Technical Center Wuhan China
1 shared publicationLiang Li
State Key Laboratory of Automotive Safety and Energy Tsinghua University Beijing China
1 shared publication
Latest Publications
- Open Access
A Hierarchical Control Scheme for Adaptive Cruise Control System Based on Model Predictive Control
An adaptive cruise control (ACC) system can improve safety and comfort during driving by taking over longitudinal control of the vehicle. It requires the coordination between the upper-layer controller and the lower-layer actuators. In this paper, a hierarchical anti-disturbance cruise control architecture based on electronic stability control (ESC) system is proposed. The upper-layer controller outputs the desired longitudinal acceleration or deceleration to the lower-layer actuators. In order to improve the accuracy of model prediction and achieve the coordinated control of multiple objectives, an upper-layer model prediction cruise controller is established based on feedback control and disturbance compensation. In addition, based on the hydraulic control unit (HCU) model and the vehicle longitudinal dynamics model, a lower-layer nonlinear model predictive deceleration controller is proposed in order to solve the problems of pressure fluctuations and the low accuracy of small decelerations when ESC is used as the actuator for the ACC system. Finally, the simulation and experimental tests were carried out. The results show that the proposed control architecture can improve the stability and comfort of the cruise control process. Moreover, compared with the traditional PID deceleration controller, it effectively improves the deceleration control accuracy.
Open AccessA Hierarchical Control Scheme for Adaptive Cruise Control System Based on Model Predictive Control
An adaptive cruise control (ACC) system can improve safety and comfort during driving by taking over longitudinal control of the vehicle. It requires the coordination between the upper-layer controller and the lower-layer actuators. In this paper, a hierarchical anti-disturbance cruise control architecture based on electronic stability control (ESC) system is proposed. The upper-layer controller outputs the desired longitudinal acceleration or deceleration to the lower-layer actuators. In order to improve the accuracy of model prediction and achieve the coordinated control of multiple objectives, an upper-layer model prediction cruise controller is established based on feedback control and disturbance compensation. In addition, based on the hydraulic control unit (HCU) model and the vehicle longitudinal dynamics model, a lower-layer nonlinear model predictive deceleration controller is proposed in order to solve the problems of pressure fluctuations and the low accuracy of small decelerations when ESC is used as the actuator for the ACC system. Finally, the simulation and experimental tests were carried out. The results show that the proposed control architecture can improve the stability and comfort of the cruise control process. Moreover, compared with the traditional PID deceleration controller, it effectively improves the deceleration control accuracy.
- Open Access
UKF-Based Observer Design for the Electric Brake Booster in Situations of Disturbance
The motor-driven electric brake booster (E-Booster) can replace the traditional vacuum booster to realize the braking power assistance and active braking. Independent of extra sensors, this paper proposes a full-state observer for E-Booster based on Unscented Kalman Filter (UKF) in the presence of a driver’s input force disturbance. The electro-hydraulic system is first modeled, which includes a nonlinear hydraulic model and the reaction disk’s rubber model. The pre-compression is designed to produce linear power assistance based on the properties of rubber material. With the existence of the disturbance, the linear quadratic regulator (LQR) algorithm is used to track the pre-compression of the reaction disk so that E-Booster is developed into a closed-loop system to achieve power assistance. The proposed UKF observer can online estimate the states considering the controller input and disturbance input. To reduce the process error, the hydraulic p-V characteristic is fitted using the recursive least squares (RLS) method before observation. Furthermore, the simulation test and vehicle tests are performed to validate the observation effect. In the closed-loop test, UKF decreases residual error by 16% when compared to the typical Extended Kalman Filter (EKF). The simulation results remain consistent with the experimental results, demonstrating the effectiveness of the proposed method.
Open AccessUKF-Based Observer Design for the Electric Brake Booster in Situations of Disturbance
The motor-driven electric brake booster (E-Booster) can replace the traditional vacuum booster to realize the braking power assistance and active braking. Independent of extra sensors, this paper proposes a full-state observer for E-Booster based on Unscented Kalman Filter (UKF) in the presence of a driver’s input force disturbance. The electro-hydraulic system is first modeled, which includes a nonlinear hydraulic model and the reaction disk’s rubber model. The pre-compression is designed to produce linear power assistance based on the properties of rubber material. With the existence of the disturbance, the linear quadratic regulator (LQR) algorithm is used to track the pre-compression of the reaction disk so that E-Booster is developed into a closed-loop system to achieve power assistance. The proposed UKF observer can online estimate the states considering the controller input and disturbance input. To reduce the process error, the hydraulic p-V characteristic is fitted using the recursive least squares (RLS) method before observation. Furthermore, the simulation test and vehicle tests are performed to validate the observation effect. In the closed-loop test, UKF decreases residual error by 16% when compared to the typical Extended Kalman Filter (EKF). The simulation results remain consistent with the experimental results, demonstrating the effectiveness of the proposed method.
- Open Access
- 10 November 2022
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 17 (3) , 566-578
An autonomous emergency braking strategy based on non‐linear model predictive deceleration control
Surrogate safety measures (SSM) are used to assess the risk for autonomous emergency braking system (AEBS). Developing appropriate SSM and accurately executing the braking request are the key issues. Time‐to‐collision (TTC) is a typical time‐based SSM with limitations. By analyzing the braking process, this paper proposes a new SSM based on deceleration rate to avoid collision (DRAC). As the brake actuator, vehicle electronic stability control (ESC) system has many problems, such as large overshoot and pressure fluctuation. Considering the model of hydraulic control unit (HCU) and vehicle, a deceleration controller based on non‐linear model predictive control (NMPC) is proposed. Based on this, a layered AEBS architecture is proposed. The upper‐layer AEBS controller calculates the expected deceleration based on modified DRAC (MDRAC), and transmits it to the lower‐layer NMPC deceleration controller. Finally, the simulation and experimental tests are carried out. The results show that the system has a fast and stable response. In addition, the performance of the proposed AEBS strategy is tested according to the Euro‐NCAP test protocol. Comparing the results with the TTC method, the proposed method can improve the stability of the distance margin by more than 0.55 m, which ensures the safety and improves the stability of the vehicle.
- 10 November 2022
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 17 (3) , 566-578
Open AccessAn autonomous emergency braking strategy based on non‐linear model predictive deceleration control
Surrogate safety measures (SSM) are used to assess the risk for autonomous emergency braking system (AEBS). Developing appropriate SSM and accurately executing the braking request are the key issues. Time‐to‐collision (TTC) is a typical time‐based SSM with limitations. By analyzing the braking process, this paper proposes a new SSM based on deceleration rate to avoid collision (DRAC). As the brake actuator, vehicle electronic stability control (ESC) system has many problems, such as large overshoot and pressure fluctuation. Considering the model of hydraulic control unit (HCU) and vehicle, a deceleration controller based on non‐linear model predictive control (NMPC) is proposed. Based on this, a layered AEBS architecture is proposed. The upper‐layer AEBS controller calculates the expected deceleration based on modified DRAC (MDRAC), and transmits it to the lower‐layer NMPC deceleration controller. Finally, the simulation and experimental tests are carried out. The results show that the system has a fast and stable response. In addition, the performance of the proposed AEBS strategy is tested according to the Euro‐NCAP test protocol. Comparing the results with the TTC method, the proposed method can improve the stability of the distance margin by more than 0.55 m, which ensures the safety and improves the stability of the vehicle.
- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (6) , 6119-6130
A Robust Unscented M-Estimation-Based Filter for Vehicle State Estimation With Unknown Input
Longitudinal velocity, lateral velocity, and front wheel steering angle are crucial states for vehicle active safety features. However, direct measurement of these variables requires expensive measurement instruments and can be easily affected by vehicle nonlinear dynamics, outliers and noise pollution. Moreover, unknown inputs bring great challenges to their accurate estimation. Therefore, this paper develops a novel robust unscented M-estimation-based filter (RUMF) for vehicle state estimation with unknown driver steering torque. The nonlinear system model is constructed based on the vehicle dynamics model. Unscented transformation (UT) and statistical linearization are implemented to transform the nonlinear process and measurement function into a linear-like regression form with data redundancy to achieve outlier suppression. Then, an M-estimation-based iterated algorithm is designed to address process uncertainty and innovation and observation outliers for robust vehicle state estimation. The iteratively reweighted least-squares (IRLS) method based on the M-estimation methodology is utilized for unknown input estimation. Simulations and experimental results compared with extended Kalman filter (EKF) and particle filter (PF) have verified the effectiveness and robustness of the proposed algorithm.
- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (6) , 6119-6130
A Robust Unscented M-Estimation-Based Filter for Vehicle State Estimation With Unknown Input
Longitudinal velocity, lateral velocity, and front wheel steering angle are crucial states for vehicle active safety features. However, direct measurement of these variables requires expensive measurement instruments and can be easily affected by vehicle nonlinear dynamics, outliers and noise pollution. Moreover, unknown inputs bring great challenges to their accurate estimation. Therefore, this paper develops a novel robust unscented M-estimation-based filter (RUMF) for vehicle state estimation with unknown driver steering torque. The nonlinear system model is constructed based on the vehicle dynamics model. Unscented transformation (UT) and statistical linearization are implemented to transform the nonlinear process and measurement function into a linear-like regression form with data redundancy to achieve outlier suppression. Then, an M-estimation-based iterated algorithm is designed to address process uncertainty and innovation and observation outliers for robust vehicle state estimation. The iteratively reweighted least-squares (IRLS) method based on the M-estimation methodology is utilized for unknown input estimation. Simulations and experimental results compared with extended Kalman filter (EKF) and particle filter (PF) have verified the effectiveness and robustness of the proposed algorithm.