Wanderson Magno Paiva Barbosa de Lima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Wanderson Magno Paiva Barbosa de Lima has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Gilson Barbosa de Lima
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil
18 shared publications - Elisiane Santana de Lima
Federal University of Campina Grande
15 shared publications - Hortência Luma Fernandes Magalhães
Department of Chemical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil
13 shared publications - Ricardo Soares Gomez
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil
13 shared publications - Túlio Rafael Nascimento Porto
Universidade Federal de Campina Grande
9 shared publications - João M. P. Q. Delgado
CONSTRUCT, Department of Civil Engineering, Faculty of Engineering, University of Porto, 4200-465 Porto, Portugal
5 shared publications
Latest Publications
- Open Access
- 1 March 2022
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2022, 1-15
Behind the Manufacturing of Industrial Clay Bricks: Drying Stage Predictions Using CFD
Drying of ceramic materials plays important role for industry, involving questions related to investments, energy consumption, product quality, and environmental pollution. In this sense, this work aims to predict heat and mass transfer during the drying process of an industrial clay brick in oven. Simulations were carried out by computational fluid dynamics (Ansys CFX software). Results of the drying and heating kinetics and the moisture content and temperature distributions of the product at different elapsed times are shown and analyzed. The results showed a good agreement between the experimental data, of the surface temperature and the average moisture content, and the numerical results. From the results, it was verified that the proposed mathematical modeling was adequate, providing predicted results in accordance with the experimental data used. Furthermore, numerical results showed that an increase in drying-air temperature and a decrease in relative humidity lead to an increase in heating and moisture removal rates. In the research, it was observed that mass diffusion coefficient increased with increasing drying-air temperature.
- 1 March 2022
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2022, 1-15
Open AccessBehind the Manufacturing of Industrial Clay Bricks: Drying Stage Predictions Using CFD
Drying of ceramic materials plays important role for industry, involving questions related to investments, energy consumption, product quality, and environmental pollution. In this sense, this work aims to predict heat and mass transfer during the drying process of an industrial clay brick in oven. Simulations were carried out by computational fluid dynamics (Ansys CFX software). Results of the drying and heating kinetics and the moisture content and temperature distributions of the product at different elapsed times are shown and analyzed. The results showed a good agreement between the experimental data, of the surface temperature and the average moisture content, and the numerical results. From the results, it was verified that the proposed mathematical modeling was adequate, providing predicted results in accordance with the experimental data used. Furthermore, numerical results showed that an increase in drying-air temperature and a decrease in relative humidity lead to an increase in heating and moisture removal rates. In the research, it was observed that mass diffusion coefficient increased with increasing drying-air temperature.
- Open Access
Drying and Heating Processes in Arbitrarily Shaped Clay Materials Using Lumped Phenomenological Modeling
This work aims to study the drying of clay ceramic materials with arbitrary shapes theoretically. Advanced phenomenological mathematical models based on lumped analysis and their exact solutions are presented to predict the heat and mass transfers in the porous material and estimate the transport coefficients. Application has been made in hollow ceramic bricks. Different simulations were carried out to evaluate the effect of drying air conditions (relative humidity and speed) under conditions of forced and natural convection. The transient results of the moisture content and temperature of the brick, and the convective heat and mass transfer coefficients are presented, discussed and compared with experimental data, obtaining a good agreement. It was found that the lower the relative humidity is and the higher the speed of the drying air is, the higher the convective heat and mass transfer coefficients are at the surface of the brick and in the holes, and the faster the moisture removal material and heating is. Based on the predicted results, the best conditions for brick drying were given. The idea is to increase the quality of the brick after the process, to reduce the waste of raw material and energy consumption in the process.
Open AccessDrying and Heating Processes in Arbitrarily Shaped Clay Materials Using Lumped Phenomenological Modeling
This work aims to study the drying of clay ceramic materials with arbitrary shapes theoretically. Advanced phenomenological mathematical models based on lumped analysis and their exact solutions are presented to predict the heat and mass transfers in the porous material and estimate the transport coefficients. Application has been made in hollow ceramic bricks. Different simulations were carried out to evaluate the effect of drying air conditions (relative humidity and speed) under conditions of forced and natural convection. The transient results of the moisture content and temperature of the brick, and the convective heat and mass transfer coefficients are presented, discussed and compared with experimental data, obtaining a good agreement. It was found that the lower the relative humidity is and the higher the speed of the drying air is, the higher the convective heat and mass transfer coefficients are at the surface of the brick and in the holes, and the faster the moisture removal material and heating is. Based on the predicted results, the best conditions for brick drying were given. The idea is to increase the quality of the brick after the process, to reduce the waste of raw material and energy consumption in the process.
- Open Access
Non-Equilibrium Thermodynamics-Based Convective Drying Model Applied to Oblate Spheroidal Porous Bodies: A Finite-Volume Analysis
Commonly based on the liquid diffusion theory, drying theoretical studies in porous materials has been directed to plate, cylinder, and sphere, and few works are applied to non-conventional geometries. In this sense, this work aims to study, theoretically, the drying of solids with oblate spheroidal geometry based on the thermodynamics of irreversible processes. Mathematical modeling is proposed to describe, simultaneously, the heat and mass transfer (liquid and vapor) during the drying process, considering the variability of the transport coefficients and the convective boundary conditions on the solid surface, with particular reference to convective drying of lentil grains at low temperature and moderate air relative humidity. All the governing equations were written in the oblate spheroidal coordinates system and solved numerically using the finite-volume technique and the iterative Gauss–Seidel method. Numerical results of moisture content, temperature, liquid, vapor, and heat fluxes during the drying process were obtained, analyzed, and compared with experimental data, with a suitable agreement. It was observed that the areas near the focal point of the lentil grain dry and heat up faster; consequently, these areas are more susceptible to the appearance of cracks that can compromise the quality of the product. In addition, it was found that the vapor flux was predominant during the drying process when compared to the liquid flux.
Open AccessNon-Equilibrium Thermodynamics-Based Convective Drying Model Applied to Oblate Spheroidal Porous Bodies: A Finite-Volume Analysis
Commonly based on the liquid diffusion theory, drying theoretical studies in porous materials has been directed to plate, cylinder, and sphere, and few works are applied to non-conventional geometries. In this sense, this work aims to study, theoretically, the drying of solids with oblate spheroidal geometry based on the thermodynamics of irreversible processes. Mathematical modeling is proposed to describe, simultaneously, the heat and mass transfer (liquid and vapor) during the drying process, considering the variability of the transport coefficients and the convective boundary conditions on the solid surface, with particular reference to convective drying of lentil grains at low temperature and moderate air relative humidity. All the governing equations were written in the oblate spheroidal coordinates system and solved numerically using the finite-volume technique and the iterative Gauss–Seidel method. Numerical results of moisture content, temperature, liquid, vapor, and heat fluxes during the drying process were obtained, analyzed, and compared with experimental data, with a suitable agreement. It was observed that the areas near the focal point of the lentil grain dry and heat up faster; consequently, these areas are more susceptible to the appearance of cracks that can compromise the quality of the product. In addition, it was found that the vapor flux was predominant during the drying process when compared to the liquid flux.
- Open Access
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Secagem de tijolos cerâmicos industriais e estimativa de parâmetros do processo: uma abordagem concentrada avançada
Este trabalho objetiva estudar a secagem de sólidos porosos e com forma arbitraria usando o método da análise concentrada. Um modelo matemático fenomenológico avançado baseado numa análise concentrada e sua solução exata são apresentados para predizer as transferências de massa e calor em tijolos cerâmicos vazados industriais e estimar os coeficientes de transporte. Diferentes simulações foram realizadas para avaliar o efeito da temperatura do ar no processo de secagem. Resultados transientes do teor de umidade e temperatura do tijolo, e dos coeficientes de transferência de calor e massa convectivos são apresentados e discutidos. Verificou-se que, quanto maior a temperatura, maiores são os coeficientes de transferência de calor e massa convectivos na superfície do tijolo, e mais rápido o produto perde umidade e eleva sua temperatura. Do estudo, propõe-se uma condição otimizada de secagem do tijolo cerâmico industrial visando minimizar os defeitos no produto pós-secagem, aumentar sua qualidade para a etapa de queima, reduzir desperdícios de matéria-prima e economizar energia no processo.
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Open AccessSecagem de tijolos cerâmicos industriais e estimativa de parâmetros do processo: uma abordagem concentrada avançada
Este trabalho objetiva estudar a secagem de sólidos porosos e com forma arbitraria usando o método da análise concentrada. Um modelo matemático fenomenológico avançado baseado numa análise concentrada e sua solução exata são apresentados para predizer as transferências de massa e calor em tijolos cerâmicos vazados industriais e estimar os coeficientes de transporte. Diferentes simulações foram realizadas para avaliar o efeito da temperatura do ar no processo de secagem. Resultados transientes do teor de umidade e temperatura do tijolo, e dos coeficientes de transferência de calor e massa convectivos são apresentados e discutidos. Verificou-se que, quanto maior a temperatura, maiores são os coeficientes de transferência de calor e massa convectivos na superfície do tijolo, e mais rápido o produto perde umidade e eleva sua temperatura. Do estudo, propõe-se uma condição otimizada de secagem do tijolo cerâmico industrial visando minimizar os defeitos no produto pós-secagem, aumentar sua qualidade para a etapa de queima, reduzir desperdícios de matéria-prima e economizar energia no processo.
- Open Access
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Transferência de calor em Reator Cilíndrico Elíptico de leito fixo via modelo heterogêneo: efeito da forma das partículas do leito poroso
O objetivo deste trabalho foi estudar a transferência de calor em um reator cilíndrico elíptico de leito recheado de partículas. Foi desenvolvido um modelo matemático heterogêneo (modelo de duas fases), aplicado para as fases sólida e fluida separadamente. Para resolver as equações diferenciais parciais foi utilizado o método de volume finito, a formulação totalmente implícita, e o esquema WUDS para interpolação para os termos convectivos e difusivos. Resultados da distribuição de temperatura nas fases fluida e sólida, ao longo do reator, para partículas com forma esferoidal prolata e esférica são apresentados e analisados. Verificou-se que a forma da partícula que compõe o leito poroso afeta levemente a distribuição de temperatura no interior do reator e que a temperatura adimensional da fase fluida é levemente menor que a da fase sólida.
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Open AccessTransferência de calor em Reator Cilíndrico Elíptico de leito fixo via modelo heterogêneo: efeito da forma das partículas do leito poroso
O objetivo deste trabalho foi estudar a transferência de calor em um reator cilíndrico elíptico de leito recheado de partículas. Foi desenvolvido um modelo matemático heterogêneo (modelo de duas fases), aplicado para as fases sólida e fluida separadamente. Para resolver as equações diferenciais parciais foi utilizado o método de volume finito, a formulação totalmente implícita, e o esquema WUDS para interpolação para os termos convectivos e difusivos. Resultados da distribuição de temperatura nas fases fluida e sólida, ao longo do reator, para partículas com forma esferoidal prolata e esférica são apresentados e analisados. Verificou-se que a forma da partícula que compõe o leito poroso afeta levemente a distribuição de temperatura no interior do reator e que a temperatura adimensional da fase fluida é levemente menor que a da fase sólida.
- Open Access
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Thermal analysis in an air conditioning duct: An experimental design approach
The main purpose of this work is to perform a thermal analysis in an air conditioning duct to verify the influence of the thermal properties of the insulating material on the minimum thermal insulation thickness necessary to avoid the condensation of water vapor present in the air. The mathematical formulation is based on Fourier’s law and the first law of thermodynamics. A response surface, a contour plot and a mathematical model for the analyzed response variable, were obtained from an experimental design. Results indicate that the reduction of thermal conductivity and increase of emissivity of the insulating material contribute to the reduction of the minimum thermal insulation thickness.
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Open AccessThermal analysis in an air conditioning duct: An experimental design approach
The main purpose of this work is to perform a thermal analysis in an air conditioning duct to verify the influence of the thermal properties of the insulating material on the minimum thermal insulation thickness necessary to avoid the condensation of water vapor present in the air. The mathematical formulation is based on Fourier’s law and the first law of thermodynamics. A response surface, a contour plot and a mathematical model for the analyzed response variable, were obtained from an experimental design. Results indicate that the reduction of thermal conductivity and increase of emissivity of the insulating material contribute to the reduction of the minimum thermal insulation thickness.
- Open Access
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Modelagem e simulação de escoamento anular de água, óleo pesado e ar em dutos horizontais
Este artigo tem como objetivo estudar o escoamento trifásico água – óleo pesado – ar em dutos horizontais, utilizando a técnica “core annular flow”. O modelo matemático utilizado foi o não-homogêneo, numa abordagem Euleriana – Euleriana. Considerou-se o modelo de mistura para tratar os termos de transferência de momento interfacial entre as fases contínuas (água e óleo pesado) e o modelo de partícula para tratar os termos de transferência de momento interfacial entre as fases dispersa e contínua (ar e óleo pesado). Todas as simulações foram realizadas utilizando o Software CFX versão 11. Resultados dos campos de pressão e fração volumétrica das fases e queda de pressão no duto são apresentados e comparados com dados experimentais. Verificou-se que a modelagem matemática utilizada foi adequada, apresentado erro máximo com relação aos dados experimentais de queda de pressão de 7,3%, demonstrando a eficiência da técnica core-flow para o transporte trifásico de água - óleo pesado – ar.
- 10 December 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (12)
Open AccessModelagem e simulação de escoamento anular de água, óleo pesado e ar em dutos horizontais
Este artigo tem como objetivo estudar o escoamento trifásico água – óleo pesado – ar em dutos horizontais, utilizando a técnica “core annular flow”. O modelo matemático utilizado foi o não-homogêneo, numa abordagem Euleriana – Euleriana. Considerou-se o modelo de mistura para tratar os termos de transferência de momento interfacial entre as fases contínuas (água e óleo pesado) e o modelo de partícula para tratar os termos de transferência de momento interfacial entre as fases dispersa e contínua (ar e óleo pesado). Todas as simulações foram realizadas utilizando o Software CFX versão 11. Resultados dos campos de pressão e fração volumétrica das fases e queda de pressão no duto são apresentados e comparados com dados experimentais. Verificou-se que a modelagem matemática utilizada foi adequada, apresentado erro máximo com relação aos dados experimentais de queda de pressão de 7,3%, demonstrando a eficiência da técnica core-flow para o transporte trifásico de água - óleo pesado – ar.
- Open Access
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Análise do processo de separação óleo-água em hidrociclones via CFD
Hidrociclones são equipamentos usados em processos de separação óleo-água. São considerados eficientes, compactos, seguros, de simples construção e manutenção, e baixo custo, quando comparados a outros equipamentos de semelhante aplicação. Diante disso, este trabalho tem como objetivo analisar numericamente o processo de separação da mistura óleo-água em um hidrociclone, quanto ao seu aspecto fluidodinâmico. Para a solução numérica das equações governantes utilizou-se o software Ansys CFX. Resultados dos campos de pressão e fração volumétrica da fase óleo, e do desempenho de separação do equipamento são apresentados e analisados. Dos resultados obtidos verificou-se que as maiores pressões ocorrem próximo as paredes e entrada do equipamento, que as maiores frações volumétricas do óleo ocorrem na região central e próximo a saída do hidrociclone, e que este equipamento apresentou uma eficiência de separação superior a 99,8%.
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Open AccessAnálise do processo de separação óleo-água em hidrociclones via CFD
Hidrociclones são equipamentos usados em processos de separação óleo-água. São considerados eficientes, compactos, seguros, de simples construção e manutenção, e baixo custo, quando comparados a outros equipamentos de semelhante aplicação. Diante disso, este trabalho tem como objetivo analisar numericamente o processo de separação da mistura óleo-água em um hidrociclone, quanto ao seu aspecto fluidodinâmico. Para a solução numérica das equações governantes utilizou-se o software Ansys CFX. Resultados dos campos de pressão e fração volumétrica da fase óleo, e do desempenho de separação do equipamento são apresentados e analisados. Dos resultados obtidos verificou-se que as maiores pressões ocorrem próximo as paredes e entrada do equipamento, que as maiores frações volumétricas do óleo ocorrem na região central e próximo a saída do hidrociclone, e que este equipamento apresentou uma eficiência de separação superior a 99,8%.
- Open Access
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Processo de secagem de materiais cerâmicos argilosos: uma revisão
A secagem é uma operação de transferência de calor e massa envolvendo a remoção de umidade, sendo uma etapa importante e de elevado custo no processo de manufatura de diversos produtos. Para materiais cerâmicos, o processo de secagem é necessário para retirar a água que foi adicionada a argila na etapa de moldagem e conferir a resistência necessária para reduzir as chances de falhas durante a etapa de queima do produto. O controle do processo de secagem é essencial para reduzir defeitos no material, perda de produtividade e consumo energético. Devido à importância, esse trabalho tem por objetivo apresentar uma revisão de diversos tópicos relacionados com a secagem de materiais cerâmicos. Aqui são discutidos diferentes aspectos tais como: os fundamentos, as cinéticas de remoção de umidade, os defeitos, o controle e a otimização do processo de secagem, com ênfase a produtos de argila. A ideia é fornecer subsídios para que pesquisadores e industriais possam melhorar seus conhecimentos e tomar decisões apropriadas sobre este tópico de grande importância para a economia do país.
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Open AccessProcesso de secagem de materiais cerâmicos argilosos: uma revisão
A secagem é uma operação de transferência de calor e massa envolvendo a remoção de umidade, sendo uma etapa importante e de elevado custo no processo de manufatura de diversos produtos. Para materiais cerâmicos, o processo de secagem é necessário para retirar a água que foi adicionada a argila na etapa de moldagem e conferir a resistência necessária para reduzir as chances de falhas durante a etapa de queima do produto. O controle do processo de secagem é essencial para reduzir defeitos no material, perda de produtividade e consumo energético. Devido à importância, esse trabalho tem por objetivo apresentar uma revisão de diversos tópicos relacionados com a secagem de materiais cerâmicos. Aqui são discutidos diferentes aspectos tais como: os fundamentos, as cinéticas de remoção de umidade, os defeitos, o controle e a otimização do processo de secagem, com ênfase a produtos de argila. A ideia é fornecer subsídios para que pesquisadores e industriais possam melhorar seus conhecimentos e tomar decisões apropriadas sobre este tópico de grande importância para a economia do país.
- Open Access
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Estudo teórico e experimental da secagem de banana inteira em estufa
Bananas frescas são frutas com elevado teor de umidade após a colheita, e são submetidas ao processo de secagem para minimizar desperdício e a deterioração, e aumentar a vida de prateleira. Este trabalho apresenta um estudo de secagem de banana em estufa. As bananas inteiras foram descascadas manualmente e secas nas temperaturas de 50 e 60ºC. Modelos concentrados de transferência de calor e massa e variações do volume da banana foram propostos e ajustados aos dados experimentais apresentando uma boa concordância. Os resultados revelaram que a temperatura do ar de secagem e a relação área/volume afetam significativamente a secagem, aquecimento e encolhimento da banana.
- 31 October 2020
- Published by Research, Society and Development in Research, Society and Development
- Vol. 9 (11)
Open AccessEstudo teórico e experimental da secagem de banana inteira em estufa
Bananas frescas são frutas com elevado teor de umidade após a colheita, e são submetidas ao processo de secagem para minimizar desperdício e a deterioração, e aumentar a vida de prateleira. Este trabalho apresenta um estudo de secagem de banana em estufa. As bananas inteiras foram descascadas manualmente e secas nas temperaturas de 50 e 60ºC. Modelos concentrados de transferência de calor e massa e variações do volume da banana foram propostos e ajustados aos dados experimentais apresentando uma boa concordância. Os resultados revelaram que a temperatura do ar de secagem e a relação área/volume afetam significativamente a secagem, aquecimento e encolhimento da banana.