María Elvira Garrido
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
María Elvira Garrido has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Roberto Tomás
Departamento de Ingeniería Civil, Escuela Politécnica Superior de Alicante, Universidad de Alicante, P.O. Box 99, 03080 Alicante, Spain
6 shared publications - Carlos Hidalgo Signes
Departamento de Ingeniería del Terreno, Universitat Politècnica de València, Camí de Vera s/n, 46022 Valencia, Spain
5 shared publications - Víctor Martínez-Ibáñez
Department of Construction Engineering and Civil Engineering Projects. Universitat Politècnica de València. 46022 Valencia, Spain
5 shared publications - Tiago Miranda
Universidade do Minho, Portugal
2 shared publications A Basco
Università degli studi della Campania Luigi Vanvitelli, 81100 Caserta, Italy
1 shared publication- Aniello Basco
Dipartimento di Ingegneria, Università degli Studi della Campania Luigi Vanvitelli, 81100 Caserta, Italy
1 shared publication
Latest Publications
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 523-528
Thermal Cycling Effects on Granite Pore Structure at Moderate Temperatures
Thermally induced microfracturing has emerged as an effective method to enhance permeability of low-porosity crystalline rocks in Enhanced Geothermal Systems (EGS). Most existing studies focus on high-temperature treatments (>500 °C), which limits their applicability under field conditions, where moderate temperatures and controlled thermal shocks are preferred. This study examines the evolution of porosity and pore structure in granite subjected to repeated heating-cooling cycles at relatively low temperatures to assess the feasibility of inducing microfracture development in geothermal reservoir stimulation. Granite samples were heated to 200, 300, and 400 °C and then cooled by immersion in water to generate a steep thermal gradient. Different groups of samples were exposed to 1 to 5 thermal cycles. Total and open porosity, density, and ultrasonic wave velocity were determined to assess progressive thermal damage. In addition, mercury intrusion porosimetry was performed to characterize variations in pore volume, pore size distribution, and pore connectivity. X-ray diffraction (XRD) analysis was conducted to detect potential mineralogical changes resulting from repeated thermal exposure. The results show a progressive decrease in bulk density and ultrasonic velocities with increasing temperature and cycle count, indicating the accumulation of microstructural damage. Open porosity shows a significant increase, particularly at 300 and 400 °C, while total porosity shows more limited changes, suggesting that increasing the cycle count improves pore connectivity. The porosimetry results confirm a shift toward larger pore sizes and improved connectivity after five cycles, especially at higher temperatures, reflecting microcrack coalescence. XRD analyses show no peak displacements or new mineral phases, confirming that the observed changes are not associated with mineralogical transformations. Overall, this study demonstrates that thermal treatment at moderate temperatures effectively improves porosity and microfracture connectivity in these rocks, offering a practical and energy-efficient method for geothermal reservoir stimulation.
- 12 August 2026
- Published by Macedonian Association for Geotechnics
- p. 523-528
Thermal Cycling Effects on Granite Pore Structure at Moderate Temperatures
Thermally induced microfracturing has emerged as an effective method to enhance permeability of low-porosity crystalline rocks in Enhanced Geothermal Systems (EGS). Most existing studies focus on high-temperature treatments (>500 °C), which limits their applicability under field conditions, where moderate temperatures and controlled thermal shocks are preferred. This study examines the evolution of porosity and pore structure in granite subjected to repeated heating-cooling cycles at relatively low temperatures to assess the feasibility of inducing microfracture development in geothermal reservoir stimulation. Granite samples were heated to 200, 300, and 400 °C and then cooled by immersion in water to generate a steep thermal gradient. Different groups of samples were exposed to 1 to 5 thermal cycles. Total and open porosity, density, and ultrasonic wave velocity were determined to assess progressive thermal damage. In addition, mercury intrusion porosimetry was performed to characterize variations in pore volume, pore size distribution, and pore connectivity. X-ray diffraction (XRD) analysis was conducted to detect potential mineralogical changes resulting from repeated thermal exposure. The results show a progressive decrease in bulk density and ultrasonic velocities with increasing temperature and cycle count, indicating the accumulation of microstructural damage. Open porosity shows a significant increase, particularly at 300 and 400 °C, while total porosity shows more limited changes, suggesting that increasing the cycle count improves pore connectivity. The porosimetry results confirm a shift toward larger pore sizes and improved connectivity after five cycles, especially at higher temperatures, reflecting microcrack coalescence. XRD analyses show no peak displacements or new mineral phases, confirming that the observed changes are not associated with mineralogical transformations. Overall, this study demonstrates that thermal treatment at moderate temperatures effectively improves porosity and microfracture connectivity in these rocks, offering a practical and energy-efficient method for geothermal reservoir stimulation.
- Open Access
- 19 December 2023
- Published by MDPI AG in Sustainability
- Vol. 16 (1) , 8
A New SJ* Value Based on Sievers’ J-Miniature Drill Tests to Determine the Drillability of Limestones
This research presents a new drillability value (SJ*) that corrects the most-used Sievers’ J-value (SJ) by removing the accommodation effect of the drill bit in the first tenths of a millimetre to better represent the real drillability of limestones. Moreover, this research demonstrates how such an effect is more notable when porosity and micro-cracking increase, which in this study has been achieved by inducing thermal damage in the samples. To do so, limestone samples from the Prada formation were subjected to temperatures of 105, 300 and 600 °C and then cooled at fast and slow rates to induce porosity and micro-cracking. Two characteristic zones were identified in the penetration–time plots: (a) a shallow region (Zone 1) with a variable drilling rate including an initial peak and (b) a deeper region (Zone 2) where the drilling rate stabilises. These drilling rates increase with thermally induced porosity and micro-cracking, and the authors propose a new method to delimit Zones 1 and 2. Zone 1 is attributed to the time it takes for the drill bit to adjust and settle in the rock surface, while Zone 2 more realistically represents the drillability of the material. The above influences the SJ value derived from Sievers’ J-miniature drill tests, so a new drillability value SJ* is proposed that corrects SJ by excluding Zone 1 and giving more weight to Zone 2. The novel SJ* presented in this research constitutes a more accurate tool to assess and predict the drilling performance in limestones.
- 19 December 2023
- Published by MDPI AG in Sustainability
- Vol. 16 (1) , 8
Open AccessA New SJ* Value Based on Sievers’ J-Miniature Drill Tests to Determine the Drillability of Limestones
This research presents a new drillability value (SJ*) that corrects the most-used Sievers’ J-value (SJ) by removing the accommodation effect of the drill bit in the first tenths of a millimetre to better represent the real drillability of limestones. Moreover, this research demonstrates how such an effect is more notable when porosity and micro-cracking increase, which in this study has been achieved by inducing thermal damage in the samples. To do so, limestone samples from the Prada formation were subjected to temperatures of 105, 300 and 600 °C and then cooled at fast and slow rates to induce porosity and micro-cracking. Two characteristic zones were identified in the penetration–time plots: (a) a shallow region (Zone 1) with a variable drilling rate including an initial peak and (b) a deeper region (Zone 2) where the drilling rate stabilises. These drilling rates increase with thermally induced porosity and micro-cracking, and the authors propose a new method to delimit Zones 1 and 2. Zone 1 is attributed to the time it takes for the drill bit to adjust and settle in the rock surface, while Zone 2 more realistically represents the drillability of the material. The above influences the SJ value derived from Sievers’ J-miniature drill tests, so a new drillability value SJ* is proposed that corrects SJ by excluding Zone 1 and giving more weight to Zone 2. The novel SJ* presented in this research constitutes a more accurate tool to assess and predict the drilling performance in limestones.
- Top Cited PapersOpen Access
- 12 October 2021
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (1) , 1-17
Predicting the Uniaxial Compressive Strength of a Limestone Exposed to High Temperatures by Point Load and Leeb Rebound Hardness Testing
The effect of exposure to high temperature on rock strength is a topic of interest in many engineering fields. In general, rock strength is known to decrease as temperature increases. The most common test used to evaluate the rock strength is the uniaxial compressive strength test (UCS). It can only be carried out in laboratory and presents some limitations in terms of the number, type and preparation of the samples. Such constrains are more evident in case of rocks from historical monuments affected by a fire, where the availability of samples is limited. There are alternatives for an indirect determination of UCS, such as the point load test (PLT), or non-destructive tests such as the Schmidt’s hammer, that can also be performed in situ. The aims of this research are: (i) measuring the effect of high temperatures and cooling methods on the strength and hardness of a limestone named Pedra de Borriol widely used in several historic buildings on the E of Spain, and (ii) studying the possibility of indirectly obtaining UCS by means of PLT and Leeb hardness tests (LHT), using Equotip type D. Limestone samples were heated to 105 (standard conditions), 200, 300, 400, 500, 600, 700, 800 and 900 ºC and cooled slowly (in air) and quickly (immersed in water). After that, UCS, PLT and LHT tests were performed to evaluate the changes as temperature increases. Results show decreases over 90% in UCS, of between 50 and 70% in PLT index and smaller than 60% in LHT index. Insignificant differences between cooling methods were observed, although slowly cooled samples provide slightly higher values than quickly cooled ones. The results indicate that LHT can be used to indirectly estimate UCS, providing an acceptable prediction. Research on correlating strength parameters in rocks after thermally treated is still scarce. This research novelty provides correlations to predict UCS in historic buildings if affected by a fire, from PLT and non-destructive methods such as LHT whose determination is quicker and easier.
- 12 October 2021
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (1) , 1-17
Top Cited PapersOpen AccessPredicting the Uniaxial Compressive Strength of a Limestone Exposed to High Temperatures by Point Load and Leeb Rebound Hardness Testing
The effect of exposure to high temperature on rock strength is a topic of interest in many engineering fields. In general, rock strength is known to decrease as temperature increases. The most common test used to evaluate the rock strength is the uniaxial compressive strength test (UCS). It can only be carried out in laboratory and presents some limitations in terms of the number, type and preparation of the samples. Such constrains are more evident in case of rocks from historical monuments affected by a fire, where the availability of samples is limited. There are alternatives for an indirect determination of UCS, such as the point load test (PLT), or non-destructive tests such as the Schmidt’s hammer, that can also be performed in situ. The aims of this research are: (i) measuring the effect of high temperatures and cooling methods on the strength and hardness of a limestone named Pedra de Borriol widely used in several historic buildings on the E of Spain, and (ii) studying the possibility of indirectly obtaining UCS by means of PLT and Leeb hardness tests (LHT), using Equotip type D. Limestone samples were heated to 105 (standard conditions), 200, 300, 400, 500, 600, 700, 800 and 900 ºC and cooled slowly (in air) and quickly (immersed in water). After that, UCS, PLT and LHT tests were performed to evaluate the changes as temperature increases. Results show decreases over 90% in UCS, of between 50 and 70% in PLT index and smaller than 60% in LHT index. Insignificant differences between cooling methods were observed, although slowly cooled samples provide slightly higher values than quickly cooled ones. The results indicate that LHT can be used to indirectly estimate UCS, providing an acceptable prediction. Research on correlating strength parameters in rocks after thermally treated is still scarce. This research novelty provides correlations to predict UCS in historic buildings if affected by a fire, from PLT and non-destructive methods such as LHT whose determination is quicker and easier.
- Open Access
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 833 (1) , 012053
Variation of Drilling Rate Index (DRI) with temperature and its relationship with thermal damage on ‘Prada’ limestone
This research evaluates the variation in the Drilling Rate Index (DRI) and its relationship with thermal damage on thermally treated rocks. Samples from ‘Prada’ limestone, a lower cretaceous formation in the southern Pyrenees (Lleida, Spain), were subjected to temperatures of 105, 300, 400 and 500 °C and then cooled at a slow rate. Ultrasound P-wave velocity tests were performed before and after heating the samples to evaluate the thermal damage experienced by the rock. Sievers’ J miniature drill and brittleness tests were conducted on intact and thermally treated samples, and then resulting SJ and S20 values were combined to determine DRI. The obtained results show that thermal treatment allowed an increase of 34% in the DRI of ‘Prada’ limestone at 500 °C. DRI exhibited the same variation trend than S20, so we can conclude that thermal variation in DRI is more influenced by S20 than by SJ in ‘Prada’ limestone. We also report a strong relationship between DRI and P-wave velocity, confirming a tight dependence between the drilling performance and the thermally induced damage on the limestone. The observed substantial improvement in the drillability of the rock when heated, measured in terms of DRI value increase, could help in the advance on the development of thermally assisted mechanical excavation methods.
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 833 (1) , 012053
Open AccessVariation of Drilling Rate Index (DRI) with temperature and its relationship with thermal damage on ‘Prada’ limestone
This research evaluates the variation in the Drilling Rate Index (DRI) and its relationship with thermal damage on thermally treated rocks. Samples from ‘Prada’ limestone, a lower cretaceous formation in the southern Pyrenees (Lleida, Spain), were subjected to temperatures of 105, 300, 400 and 500 °C and then cooled at a slow rate. Ultrasound P-wave velocity tests were performed before and after heating the samples to evaluate the thermal damage experienced by the rock. Sievers’ J miniature drill and brittleness tests were conducted on intact and thermally treated samples, and then resulting SJ and S20 values were combined to determine DRI. The obtained results show that thermal treatment allowed an increase of 34% in the DRI of ‘Prada’ limestone at 500 °C. DRI exhibited the same variation trend than S20, so we can conclude that thermal variation in DRI is more influenced by S20 than by SJ in ‘Prada’ limestone. We also report a strong relationship between DRI and P-wave velocity, confirming a tight dependence between the drilling performance and the thermally induced damage on the limestone. The observed substantial improvement in the drillability of the rock when heated, measured in terms of DRI value increase, could help in the advance on the development of thermally assisted mechanical excavation methods.
- Open Access
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 833 (1) , 012027
Using non-destructive testing to assess static elastic modulus of a limestone exposed to high temperatures
The determination of static elastic modulus in the laboratory requires rock core extraction and the subsequent testing of the samples by means of standardised uniaxial compressive strength tests. However, this destructive procedure is not always suitable – as in the case of protected historic buildings. In these cases, the static elastic modulus can be obtained from the dynamic elastic modulus, in turn derived from the velocity of ultrasonic waves (a non-invasive and non-destructive test). The relationship between both the dynamic and static moduli of rocks has been extensively addressed in the scientific literature. Furthermore, several researchers have separately studied the evolution of static or dynamic elastic moduli of rocks exposed to high temperatures – although few studies have compared both values. It is well known that the dynamic modulus is generally higher than the static modulus, and the values diverge especially in rocks with a low modulus of elasticity. These differences can be mainly explained by the effect of porosity and the size of cracks in the determination of both parameters. In this research, the relationship between static and dynamic moduli for ‘Borriol’ limestone is studied for samples previously subjected to 200, 400, 600 and 800 °C and then cooled slowly (in air) or quickly (immersed in water). The results show that the static modulus of samples heated up to 600 °C decreased 80.9 and 79.1 % and dynamic modulus decreased 62.5 and 64.8 % for slow and quick cooling samples, respectively. For samples heated to 600 and 800 °C, the static and dynamic moduli are similar. In general, no significant differences between both cooling methods are observed, even though static modulus shows more loss than dynamic modulus. Finally, linear models were used to correlate static and dynamic moduli, providing coefficients of determination of 0.99 and 0.97, for slow and quick cooling, respectively. It is also remarkable that the Edyn/Est rate was smaller than 1 for elastic moduli over 30 GPa (i.e., 105, 200 and 400 °C) and greater than 1 for lower moduli (i.e., 600 and 800 °C). The results obtained can be used to calculate the static elastic modulus of ‘Borriol’ limestone from dynamic modulus determined by non-destructive techniques.
- 1 August 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 833 (1) , 012027
Open AccessUsing non-destructive testing to assess static elastic modulus of a limestone exposed to high temperatures
The determination of static elastic modulus in the laboratory requires rock core extraction and the subsequent testing of the samples by means of standardised uniaxial compressive strength tests. However, this destructive procedure is not always suitable – as in the case of protected historic buildings. In these cases, the static elastic modulus can be obtained from the dynamic elastic modulus, in turn derived from the velocity of ultrasonic waves (a non-invasive and non-destructive test). The relationship between both the dynamic and static moduli of rocks has been extensively addressed in the scientific literature. Furthermore, several researchers have separately studied the evolution of static or dynamic elastic moduli of rocks exposed to high temperatures – although few studies have compared both values. It is well known that the dynamic modulus is generally higher than the static modulus, and the values diverge especially in rocks with a low modulus of elasticity. These differences can be mainly explained by the effect of porosity and the size of cracks in the determination of both parameters. In this research, the relationship between static and dynamic moduli for ‘Borriol’ limestone is studied for samples previously subjected to 200, 400, 600 and 800 °C and then cooled slowly (in air) or quickly (immersed in water). The results show that the static modulus of samples heated up to 600 °C decreased 80.9 and 79.1 % and dynamic modulus decreased 62.5 and 64.8 % for slow and quick cooling samples, respectively. For samples heated to 600 and 800 °C, the static and dynamic moduli are similar. In general, no significant differences between both cooling methods are observed, even though static modulus shows more loss than dynamic modulus. Finally, linear models were used to correlate static and dynamic moduli, providing coefficients of determination of 0.99 and 0.97, for slow and quick cooling, respectively. It is also remarkable that the Edyn/Est rate was smaller than 1 for elastic moduli over 30 GPa (i.e., 105, 200 and 400 °C) and greater than 1 for lower moduli (i.e., 600 and 800 °C). The results obtained can be used to calculate the static elastic modulus of ‘Borriol’ limestone from dynamic modulus determined by non-destructive techniques.
- Open Access
- 6 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3286
Thermal Effects on the Drilling Performance of a Limestone: Relationships with Physical and Mechanical Properties
This work evaluates the effect of high temperatures and cooling methods on the drillability of Prada limestone. Samples from boreholes drilled during the design stage of the Tres Ponts Tunnel in the Catalan south Pyrenean zone (Spain) were subjected to temperatures of 105, 200, 300, 400, and 600 °C, and then cooled at a slow rate or by quenching. Sievers’ J-value (SJ) and brittleness (S20) were determined on thermally treated samples, and the drilling rate index (DRI) was calculated for each temperature. The results show that thermal treatment implied a sustained increase in the drillability of the rock of up to 40% at 600 °C and a change in the drillability category (from medium to high). At 600 °C, SJ and S20 tripled and doubled, respectively, the initial values obtained for the intact rock. The results were inconclusive about the influence of the cooling method on the drilling performance of Prada limestone for the tested range of temperatures. The substantial improvement observed in the drillability of Prada limestone when heated, measured in terms of DRI, could help in the development of novel thermally-assisted mechanical excavation methods. Additionally, strong correlations between drillability variables (i.e., SJ and S20) and physical and mechanical variables of Prada limestone (i.e., P- and S-wave velocities, uniaxial compression strength, elastic modulus, and Poisson’s ratio) are proposed. Correlations will help make preliminary predictions of drillability based on properties such as uniaxial compression strength and ultrasound wave velocities.
- 6 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3286
Open AccessThermal Effects on the Drilling Performance of a Limestone: Relationships with Physical and Mechanical Properties
This work evaluates the effect of high temperatures and cooling methods on the drillability of Prada limestone. Samples from boreholes drilled during the design stage of the Tres Ponts Tunnel in the Catalan south Pyrenean zone (Spain) were subjected to temperatures of 105, 200, 300, 400, and 600 °C, and then cooled at a slow rate or by quenching. Sievers’ J-value (SJ) and brittleness (S20) were determined on thermally treated samples, and the drilling rate index (DRI) was calculated for each temperature. The results show that thermal treatment implied a sustained increase in the drillability of the rock of up to 40% at 600 °C and a change in the drillability category (from medium to high). At 600 °C, SJ and S20 tripled and doubled, respectively, the initial values obtained for the intact rock. The results were inconclusive about the influence of the cooling method on the drilling performance of Prada limestone for the tested range of temperatures. The substantial improvement observed in the drillability of Prada limestone when heated, measured in terms of DRI, could help in the development of novel thermally-assisted mechanical excavation methods. Additionally, strong correlations between drillability variables (i.e., SJ and S20) and physical and mechanical variables of Prada limestone (i.e., P- and S-wave velocities, uniaxial compression strength, elastic modulus, and Poisson’s ratio) are proposed. Correlations will help make preliminary predictions of drillability based on properties such as uniaxial compression strength and ultrasound wave velocities.
- 28 October 2020
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 54 (1) , 219-234
Temperature-Induced Explosive Behaviour and Thermo-Chemical Damage on Pyrite-Bearing Limestones: Causes and Mechanisms
- 28 October 2020
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 54 (1) , 219-234
Temperature-Induced Explosive Behaviour and Thermo-Chemical Damage on Pyrite-Bearing Limestones: Causes and Mechanisms