Aniello Basco
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aniello Basco has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Hidalgo Signes
Departamento de Ingeniería del Terreno, Universitat Politècnica de València, Camí de Vera s/n, 46022 Valencia, Spain
1 shared publication - María Elvira Garrido
Departamento de Ingeniería del Terreno, Universitat Politècnica de València, Camí de Vera s/n, 46022 Valencia, Spain
1 shared publication - Roberto Tomás
Departamento de Ingeniería Civil, Escuela Politécnica Superior de Alicante, Universidad de Alicante, P.O. Box 99, 03080 Alicante, Spain
1 shared publication - Tiago Miranda
Universidade do Minho, Portugal
1 shared publication - Víctor Martínez-Ibáñez
Department of Construction Engineering and Civil Engineering Projects. Universitat Politècnica de València. 46022 Valencia, Spain
1 shared publication
Latest Publications
- Open Access
- 6 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3286
Thermal Effects on the Drilling Performance of a Limestone: Relationships with Physical and Mechanical Properties
This work evaluates the effect of high temperatures and cooling methods on the drillability of Prada limestone. Samples from boreholes drilled during the design stage of the Tres Ponts Tunnel in the Catalan south Pyrenean zone (Spain) were subjected to temperatures of 105, 200, 300, 400, and 600 °C, and then cooled at a slow rate or by quenching. Sievers’ J-value (SJ) and brittleness (S20) were determined on thermally treated samples, and the drilling rate index (DRI) was calculated for each temperature. The results show that thermal treatment implied a sustained increase in the drillability of the rock of up to 40% at 600 °C and a change in the drillability category (from medium to high). At 600 °C, SJ and S20 tripled and doubled, respectively, the initial values obtained for the intact rock. The results were inconclusive about the influence of the cooling method on the drilling performance of Prada limestone for the tested range of temperatures. The substantial improvement observed in the drillability of Prada limestone when heated, measured in terms of DRI, could help in the development of novel thermally-assisted mechanical excavation methods. Additionally, strong correlations between drillability variables (i.e., SJ and S20) and physical and mechanical variables of Prada limestone (i.e., P- and S-wave velocities, uniaxial compression strength, elastic modulus, and Poisson’s ratio) are proposed. Correlations will help make preliminary predictions of drillability based on properties such as uniaxial compression strength and ultrasound wave velocities.
- 6 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (7) , 3286
Open AccessThermal Effects on the Drilling Performance of a Limestone: Relationships with Physical and Mechanical Properties
This work evaluates the effect of high temperatures and cooling methods on the drillability of Prada limestone. Samples from boreholes drilled during the design stage of the Tres Ponts Tunnel in the Catalan south Pyrenean zone (Spain) were subjected to temperatures of 105, 200, 300, 400, and 600 °C, and then cooled at a slow rate or by quenching. Sievers’ J-value (SJ) and brittleness (S20) were determined on thermally treated samples, and the drilling rate index (DRI) was calculated for each temperature. The results show that thermal treatment implied a sustained increase in the drillability of the rock of up to 40% at 600 °C and a change in the drillability category (from medium to high). At 600 °C, SJ and S20 tripled and doubled, respectively, the initial values obtained for the intact rock. The results were inconclusive about the influence of the cooling method on the drilling performance of Prada limestone for the tested range of temperatures. The substantial improvement observed in the drillability of Prada limestone when heated, measured in terms of DRI, could help in the development of novel thermally-assisted mechanical excavation methods. Additionally, strong correlations between drillability variables (i.e., SJ and S20) and physical and mechanical variables of Prada limestone (i.e., P- and S-wave velocities, uniaxial compression strength, elastic modulus, and Poisson’s ratio) are proposed. Correlations will help make preliminary predictions of drillability based on properties such as uniaxial compression strength and ultrasound wave velocities.