Jae-Seong Jeong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jae-Seong Jeong has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Hwa-Sun Park
Department Electrical/Chemical Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
2 shared publications - Won-Gyu Choi2 shared publications
- Byung-Min Jeon
Department Chemical Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
1 shared publication - Chang-Sub Won
Department of R&D, MSP Co., Ltd., Seoul City, Republic of Korea
1 shared publication - Chang-Yun Na
Department Chemical Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea
1 shared publication Eun-Gu Shin
Korea Elect Technol Inst KETI, New & Renewable Energy Res Ctr, 25 Saenari Ro, Seongnam City, Gyeonggi Do, Peoples R China
1 shared publication
Latest Publications
- Open Access
- 29 September 2026
- Published by Elsevier in SSRN Electronic Journal
LED field failure by delamination-controlled ingress of an organosulfur carrier and surface-mediated Ag2S growth at the Ag–phosphor interface
Localized discoloration of LEDs in an LED-TV backlight unit was investigated as a field failure. FE-SEM/EDX showed silver and sulfur co-located in the discolored region, and cross-sectional TEM/EDX showed the reaction product extending from the Ag-plated lead-frame into the phosphor layer, consistent with Ag2S. Purge-and-trap GC–MS of the reflective sheet and the LED mounting board, measured together under reflow-representative conditions, identified 9H-thioxanthen-9-one, released intact, as the only sulfur-bearing volatile; no sulfur species was found in the package materials. Pyrolysis GC–MS of the sheet alone at 500–600 °C detected no sulfur-bearing compound, which assigns the carrier to the board's UV-cured solder resist, a coating in which thioxanthones serve as photoinitiators. Cross-sections of the failed packages showed interfacial delamination between the silicone lens, the reflective cup and the lead-frame, and dye penetration at ambient pressure, which fills only an end-to-end open path, confirmed that this pathway is continuous to the internal cavity in failed units and closed in the normal comparison unit. A transport analysis separates the two candidate routes by time lag alone: 0.07 s along the 2.6 mm seam against 170–1700 s through the 1 mm of intact silicone, itself several times the 63 s the package spends above 220 °C. That comparison is independent of how strongly the carrier partitions into the encapsulant, so it is the delaminated interface rather than encapsulant permeability that governs whether sulfur reaches the metal. A temperature-weighted mass balance on the measured 4.75 µm gap shows that one 260 °C reflow excursion delivers enough sulfur for ≈190 nm of Ag2S at full conversion, so the observed film requires a C–S scission yield of some tens of per cent, with scission surface-mediated at undercoordinated silver sites rather than on close-packed terraces. Sulfur outgassing from the mounting board and package interfacial integrity are coupled root causes.
- 29 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLED field failure by delamination-controlled ingress of an organosulfur carrier and surface-mediated Ag2S growth at the Ag–phosphor interface
Localized discoloration of LEDs in an LED-TV backlight unit was investigated as a field failure. FE-SEM/EDX showed silver and sulfur co-located in the discolored region, and cross-sectional TEM/EDX showed the reaction product extending from the Ag-plated lead-frame into the phosphor layer, consistent with Ag2S. Purge-and-trap GC–MS of the reflective sheet and the LED mounting board, measured together under reflow-representative conditions, identified 9H-thioxanthen-9-one, released intact, as the only sulfur-bearing volatile; no sulfur species was found in the package materials. Pyrolysis GC–MS of the sheet alone at 500–600 °C detected no sulfur-bearing compound, which assigns the carrier to the board's UV-cured solder resist, a coating in which thioxanthones serve as photoinitiators. Cross-sections of the failed packages showed interfacial delamination between the silicone lens, the reflective cup and the lead-frame, and dye penetration at ambient pressure, which fills only an end-to-end open path, confirmed that this pathway is continuous to the internal cavity in failed units and closed in the normal comparison unit. A transport analysis separates the two candidate routes by time lag alone: 0.07 s along the 2.6 mm seam against 170–1700 s through the 1 mm of intact silicone, itself several times the 63 s the package spends above 220 °C. That comparison is independent of how strongly the carrier partitions into the encapsulant, so it is the delaminated interface rather than encapsulant permeability that governs whether sulfur reaches the metal. A temperature-weighted mass balance on the measured 4.75 µm gap shows that one 260 °C reflow excursion delivers enough sulfur for ≈190 nm of Ag2S at full conversion, so the observed film requires a C–S scission yield of some tens of per cent, with scission surface-mediated at undercoordinated silver sites rather than on close-packed terraces. Sulfur outgassing from the mounting board and package interfacial integrity are coupled root causes.
- Open Access
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
Reaction-Diffusion Mechanism in Persulfate-Based Cu Wet Etching via Simulation and Experiment
The demand for high-resolution displays has increased, inducing the need for precise and reliable wet etching processes. In this study, we examined the Cu wet etching behavior in persulfate-based etchants with various concentrations and cation types via a combined simulation and experimental approach. A multiphysics simulation incorporating electrochemical properties of etchants was constructed to investigate the concentration- and cation-dependent etching behavior, and its results were compared with etching experiments. Both approaches exhibited consistent etching rate trends, indicating that the etching rate is predominantly driven by reaction kinetics, with reactive-species availability and thermodynamic driving force contributing secondary effects. Cross-sectional morphological analysis, combined with the simulated ionic distributions, further revealed that the etching directionality exhibits a cation-dependent behavior: cations that hinder the surface reaction promote lateral ion diffusion, leading to isotropic etching, whereas those that facilitate the surface reaction favor rapid vertical dissolution, resulting in anisotropic etching. These findings demonstrate that integrating electrochemical simulation with experimental analysis offers a reliable basis for predicting Cu wet etching behavior and understanding its reaction-diffusion mechanism, informing future etchant and process design.
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessReaction-Diffusion Mechanism in Persulfate-Based Cu Wet Etching via Simulation and Experiment
The demand for high-resolution displays has increased, inducing the need for precise and reliable wet etching processes. In this study, we examined the Cu wet etching behavior in persulfate-based etchants with various concentrations and cation types via a combined simulation and experimental approach. A multiphysics simulation incorporating electrochemical properties of etchants was constructed to investigate the concentration- and cation-dependent etching behavior, and its results were compared with etching experiments. Both approaches exhibited consistent etching rate trends, indicating that the etching rate is predominantly driven by reaction kinetics, with reactive-species availability and thermodynamic driving force contributing secondary effects. Cross-sectional morphological analysis, combined with the simulated ionic distributions, further revealed that the etching directionality exhibits a cation-dependent behavior: cations that hinder the surface reaction promote lateral ion diffusion, leading to isotropic etching, whereas those that facilitate the surface reaction favor rapid vertical dissolution, resulting in anisotropic etching. These findings demonstrate that integrating electrochemical simulation with experimental analysis offers a reliable basis for predicting Cu wet etching behavior and understanding its reaction-diffusion mechanism, informing future etchant and process design.
- Open Access
- 3 October 2025
- Published by Springer Nature in Journal of Civil Structural Health Monitoring
- Vol. 15 (8) , 3909-3933
On-site real-time stress health monitoring of the steel structure of a floating photovoltaic system installed in the Soyang River over a 7-year period
The design of floating photovoltaic (PV) systems faces challenges owing to irregular environmental stressors, such as unpredictable wind speeds, wave heights, wave periods, and tidal flows. Environmental factors cause repetitive dynamic movements of the components of these systems, leading to fatigue stress. In this study, on-site real-time stress health monitoring of the material stress changes in the steel structure of a floating PV system located in a river was conducted under environmental stress conditions. A 50.4 kWp floating PV system was installed in the Soyang River in the Republic of Korea. The support structure for this system is made of steel coated with a Zn–Mg–Al alloy. To monitor environmental conditions and structural dynamics, various sensors were deployed. For real-time dynamic analysis of the movement of the steel structure, rosette strain gauges were installed. To analyse the real-time stress–strain characteristics, rosette strain gauges were placed at the connecting points of the steel structure. A maximum wind speed of 21 m/s was recorded over a period of 7 years starting in 2017. The C-type steel structure supporting the horizontal placement of the PV modules exhibited the highest stress, reaching 54.5 MPa, with stress levels increasing in correlation with the wind speed. As the floating PV structure moved over a certain distance along the X–Y axis in response to the wind pressure and surface waves at low water levels, a snap-induced impact occurred due to mooring. The stress generated under high water-level conditions with slack to taut transitions in the mooring lines of the floating PV system was greater than that observed under low water-level conditions at lower wind speeds.
- 3 October 2025
- Published by Springer Nature in Journal of Civil Structural Health Monitoring
- Vol. 15 (8) , 3909-3933
Open AccessOn-site real-time stress health monitoring of the steel structure of a floating photovoltaic system installed in the Soyang River over a 7-year period
The design of floating photovoltaic (PV) systems faces challenges owing to irregular environmental stressors, such as unpredictable wind speeds, wave heights, wave periods, and tidal flows. Environmental factors cause repetitive dynamic movements of the components of these systems, leading to fatigue stress. In this study, on-site real-time stress health monitoring of the material stress changes in the steel structure of a floating PV system located in a river was conducted under environmental stress conditions. A 50.4 kWp floating PV system was installed in the Soyang River in the Republic of Korea. The support structure for this system is made of steel coated with a Zn–Mg–Al alloy. To monitor environmental conditions and structural dynamics, various sensors were deployed. For real-time dynamic analysis of the movement of the steel structure, rosette strain gauges were installed. To analyse the real-time stress–strain characteristics, rosette strain gauges were placed at the connecting points of the steel structure. A maximum wind speed of 21 m/s was recorded over a period of 7 years starting in 2017. The C-type steel structure supporting the horizontal placement of the PV modules exhibited the highest stress, reaching 54.5 MPa, with stress levels increasing in correlation with the wind speed. As the floating PV structure moved over a certain distance along the X–Y axis in response to the wind pressure and surface waves at low water levels, a snap-induced impact occurred due to mooring. The stress generated under high water-level conditions with slack to taut transitions in the mooring lines of the floating PV system was greater than that observed under low water-level conditions at lower wind speeds.
- 22 September 2025
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 295
Bilayer structure perovskite solar cells with ruddlesden-popper phase for improved stability and performance
- 22 September 2025
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 295
Bilayer structure perovskite solar cells with ruddlesden-popper phase for improved stability and performance
- 26 June 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (7) , 3695-3705
Creep-rupture durability test and FEA simulation of high temperature solder joints using simple new creep-rupture tester
- 26 June 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (7) , 3695-3705
Creep-rupture durability test and FEA simulation of high temperature solder joints using simple new creep-rupture tester
- Open Access
- 30 December 2023
- Published by The Korean Solar Energy Society in Journal of the Korean Solar Energy Society
- Vol. 43 (6) , 79-85
A Study on Improving the Stability of Perovskite Solar Cells through 2D/3D Stacked Thin Films
Organic-inorganic perovskite solar cells, which feature remarkable electrical and optical characteristics, are the most promising candidates for next-generation photovoltaic materials. However, their commercial applications are limited owing to the instability of perovskite. In this context, we conducted a study to improve the stability of perovskite using 2D/3D stacked thin films. We deposited 2D BA 2 PbI 4 (BA = butylammonium) perovskite on the surface of 3D FAPbI 3 (FA = formamidinium) perovskite via plane growth resulting in the formation of clear 2D/3D stacked thin films. The introduction of 2D perovskite leads to improved device performance and stability because defect-induced non-radiative recombination and thin-film degradation are suppressed.
- 30 December 2023
- Published by The Korean Solar Energy Society in Journal of the Korean Solar Energy Society
- Vol. 43 (6) , 79-85
Open AccessA Study on Improving the Stability of Perovskite Solar Cells through 2D/3D Stacked Thin Films
Organic-inorganic perovskite solar cells, which feature remarkable electrical and optical characteristics, are the most promising candidates for next-generation photovoltaic materials. However, their commercial applications are limited owing to the instability of perovskite. In this context, we conducted a study to improve the stability of perovskite using 2D/3D stacked thin films. We deposited 2D BA 2 PbI 4 (BA = butylammonium) perovskite on the surface of 3D FAPbI 3 (FA = formamidinium) perovskite via plane growth resulting in the formation of clear 2D/3D stacked thin films. The introduction of 2D perovskite leads to improved device performance and stability because defect-induced non-radiative recombination and thin-film degradation are suppressed.
- Open Access
- 28 December 2022
- Published by MDPI AG in Electronics
- Vol. 12 (1) , 144
Fabrication of 30 µm Sn Microbumps by Electroplating and Investigation of IMC Characteristics on Shear Strength
In this paper, we prepared a pure Sn microbump with a diameter of 30 µm using an electroplating method for a solder cap on a Cu post/Ni barrier and then determined its IMC characteristics and shear strength according to reflow recovery. In order to secure uniformity of the bump height, it was optimized through WID and WIW evaluation methods. Using an optimized plating system, bumps with a diameter of 30 µm, a height of 40 µm, and a space of 50 µm were formed on a 4-inch wafer. Shear strength was measured according to the number of reflows. IMC was evaluated through cross-sectional and plane analyses of bumps. Its correlation with shear strength according to the number of reflows was derived. The Sn plating system optimized each process condition according to the Sn concentration, current density, and temperature. The shape, surface condition, and height uniformity of the bump were quantified by a 3D profiler and FIB analysis. Height uniformity (WID) according to the concentration was confirmed to be approximately 2% when the Sn concentration was 60 g/L. WID according to the additive was confirmed to be 2% when the Sn concentration was 60 mL/L. WID according to the plating temperature was excellent in the shape of the bump at 30 °C, and a value of 2% was confirmed. The WIW for the Sn plating thickness on a 4-inch wafer was confirmed to have a value of ±3.88%. A shear test between the Cu and Sn junction was conducted to verify the shear strength of the manufactured bump. At this time, reflow was performed 1, 3, 5, 7, and 10 times for each sample. It was confirmed that as the number of flows increased, shear strength first increased. It then decreased sharply. It was confirmed that as the number of reflows increased, the thickness and cross-section area of the IMC first increased. They then gradually became saturated. The IMC between Cu and Sn was created in island form at the beginning of the reflow, resulting in increased roughness and shear strength. However, as the number of reflows increased, the roughness decreased since the IMC generated by the island was combined. The shear strength also decreased sharply.
- 28 December 2022
- Published by MDPI AG in Electronics
- Vol. 12 (1) , 144
Open AccessFabrication of 30 µm Sn Microbumps by Electroplating and Investigation of IMC Characteristics on Shear Strength
In this paper, we prepared a pure Sn microbump with a diameter of 30 µm using an electroplating method for a solder cap on a Cu post/Ni barrier and then determined its IMC characteristics and shear strength according to reflow recovery. In order to secure uniformity of the bump height, it was optimized through WID and WIW evaluation methods. Using an optimized plating system, bumps with a diameter of 30 µm, a height of 40 µm, and a space of 50 µm were formed on a 4-inch wafer. Shear strength was measured according to the number of reflows. IMC was evaluated through cross-sectional and plane analyses of bumps. Its correlation with shear strength according to the number of reflows was derived. The Sn plating system optimized each process condition according to the Sn concentration, current density, and temperature. The shape, surface condition, and height uniformity of the bump were quantified by a 3D profiler and FIB analysis. Height uniformity (WID) according to the concentration was confirmed to be approximately 2% when the Sn concentration was 60 g/L. WID according to the additive was confirmed to be 2% when the Sn concentration was 60 mL/L. WID according to the plating temperature was excellent in the shape of the bump at 30 °C, and a value of 2% was confirmed. The WIW for the Sn plating thickness on a 4-inch wafer was confirmed to have a value of ±3.88%. A shear test between the Cu and Sn junction was conducted to verify the shear strength of the manufactured bump. At this time, reflow was performed 1, 3, 5, 7, and 10 times for each sample. It was confirmed that as the number of flows increased, shear strength first increased. It then decreased sharply. It was confirmed that as the number of reflows increased, the thickness and cross-section area of the IMC first increased. They then gradually became saturated. The IMC between Cu and Sn was created in island form at the beginning of the reflow, resulting in increased roughness and shear strength. However, as the number of reflows increased, the roughness decreased since the IMC generated by the island was combined. The shear strength also decreased sharply.
- 14 October 2021
- Published by Elsevier in Microelectronics Reliability
- Vol. 126, 114402
Lifetime and degradation analysis of AgPt alloy thick film/AlN heater for semiconductor wafer annealing
- 14 October 2021
- Published by Elsevier in Microelectronics Reliability
- Vol. 126, 114402
Lifetime and degradation analysis of AgPt alloy thick film/AlN heater for semiconductor wafer annealing