AKArash Khoshkbar-Sadigh

Arash Khoshkbar-Sadigh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Arash Khoshkbar-Sadigh has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A New Single-Phase Isolated Improved Quasi Z-Source AC–AC Converter

    by Ebrahim Babaei, Alireza Razavi Majarshin, Arash Khoshkbar-Sadigh

    A new single-phase isolated improved quasi-ZS ac–ac Converter has been introduced in this article. The proposed converter is an impedance-source converter and includes their advantages. Also, it has wide range of output voltage as buck and boost in both inverting and noninverting states as well as continuous sinusoidal input current and high reliability. The converter is a high frequency transformer isolated structure in which there is no need to bulky and loss-full low frequency transformer specially in applications which require electrical isolation. The control method is very simple and only one switch works in high frequency in every half-cycle in which the switching loss is reduced. In addition, the inherent safe commutation exists and there is no need for snubber circuits or safe commutation methods. Finally, the experimental results have been brought in to verify the claims and analysis.


  • A New Flying Capacitor-Based Buck–Boost Converter for Dual-Purpose Applications

    by Tala Hemmati Shahsavar, Naser Vosoughi Kurdkandi, Oleksandr Husev, Ebrahim Babaei, Mehran Sabahi, Arash Khoshkbar-Sadigh, Dmitri Vinnikov

    A novel dual-purpose common ground dc-dc/ac power converter is proposed in this paper. It is based on the flying capacitor circuit along with boost circuit, which in turns provides a wide range of the input voltage regulation with the capability of stepping up or down the output voltage. The same components are used under both dc-dc and dc-ac modes which reduces the redundancy of the used devices. Particular attention is dedicated to the working modes of the proposed solution. The special control system is implemented to provide acceptable current and voltage quality in off-grid and grid-connected modes. To underline the pros and cons of the proposed solution, the comprehensive comparison is performed. Finally, the performance of the proposed dual-purpose power converter is investigated through an experimental 3.5 kw / 5 kw setup, for dc-ac and dc-dc operating modes, respectively. Main oscillograms along with efficiency analysis are presented and discussed in conclusions.


  • A New Five-Level Switched-Capacitor-Based Transformer-less Common-Grounded Grid-Tied Inverter

    by Milad Ghavipanjeh Marangalu, Seyed Hossein Hosseini, Naser Vosoughi Kurdkandi, Arash Khoshkbar-Sadigh

    This paper proposes a new switched-capacitor grid-tied inverter. The proposed topology can eliminate leakage current using a common-grounded strategy. Also, the proposed topology generates a five-level output voltage waveform using a single input dc source with a voltage boosting factor of 2. This structure uses six power switches, two diodes, and two self-balanced capacitors. The proposed inverter has some advantages such as a common-grounded feature, eliminated leakage current, and voltage boosting feature with single-stage energy conversion operation. Also, the proposed topology can support both active and reactive powers and generate a perfect sinusoidal output current injected into the grid. Also, to control both active and reactive powers an efficient control strategy is applied. To generate the precise gate pulses for the power switches, the introduced efficient control strategy is applied. Also, comprehensive discussions on the operating modes of the proposed inverter, Capacitor charging current analysis, the control technique, and design considerations are presented. To show the advantages and differences of the proposed inverter with some other recently presented switched-capacitor-based grid-tied inverters a comparison study is considered. Finally, to validate the performance and feasibility of the proposed inverter, various experimental results based on a 620 W experimental prototype are presented.


  • Open Access

    An Interleaved Soft Switched High Step-Up Boost Converter With High Power Density for Renewable Energy Applications

    by Ramin Rahimzadeh Khorasani, Hamed Moradmand Jazi, Nilanjan Ray Chaudhuri, Arash Khoshkbar-Sadigh, Mahdi Shaneh, Ehsan Adib, Patrick Wheeler

    In this article, a novel soft switched interleaved boost structure with a simple auxiliary circuit is proposed which is suitable for stand-alone loads or ac grid applications. In this topology, coupled inductors and switched capacitor cells of parallel modules are merged to obtain high voltage conversion ratio. The converter also has the capability of adding extra switched capacitor cells to attain very high voltage gain. To provide soft-switching condition in the wide range of output power, a new zero-voltage transition auxiliary circuit is employed which is responsible for soft switching of both phases and benefits from low conduction losses, the minimum number of semiconductor elements, and only one auxiliary gate-driver. These merits provide very high efficiency at both full-load and light loads. More importantly, no auxiliary magnetic components are utilized by taking advantage of the leakage inductance of coupled inductors for the resonant network. All semiconductor components operate under soft switching alleviating the reverse recovery problem and switching losses. Besides, the converter benefits from common ground between input and output which simplify voltage feedback. The experimental results of the interleaved converter prototype with 400-V output voltage at 400 W and 100 kHz switching frequency are provided. The full load efficiency of 98% was achieved and the power density was observed 1.9 W/Cm 3 .


  • ZVT High Step-Up Boost Converter With Wide Input Voltage and Wide Output Power for Renewable Energy Applications

    by Ramin Rahimzadeh Khorasani, Hamed Moradmand Jazi, Arash Khoshkbar-Sadigh, Nilanjan Ray Chaudhuri, Mahdi Shaneh, Najmehossadat Nourieh, Ehsan Adib, Patrick Wheeler

    In this paper a high-efficiency, high step-up DC-DC converter is introduced utilizing a new soft switching circuit based on the zero voltage transition (ZVT) technique. Soft switching performance is independent of the output load and input voltage. The simple auxiliary circuit benefits from a low number of components. The resonant circuit comprises merely one switch and one small capacitor and in comparison to the existing ZVT high step-up converters, no extra auxiliary diode and resonant inductor are used to provide soft switching. The proposed auxiliary circuit can be applied to coupled-inductors based step-up topologies, because of exploiting the leakage inductance of the coupled-inductor cell in the resonant network. Providing soft switching performance for all the semiconductor elements alleviates the reverse recovery and switching losses, which considerably enhances the efficiency. The proposed topology is a competitive structure in terms of efficiency, voltage gain ratio, and the number of components due to the mentioned features. The theoretical results are validated on a 200 W laboratory prototype with a 400 V output voltage.


  • A simple soft-switched buck converter without implementing auxiliary switch

    by Iman Talebian, Peyman Alavi, Ebrahim Babaei, Arash Khoshkbar-Sadigh


  • Analysis, Design, and Investigation of a Soft-Switched Buck Converter With High Efficiency

    by Iman Talebian, Peyman Alavi, Vafa Marzang, Ebrahim Babaei, Arash Khoshkbar-Sadigh

    In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.


  • A Modified Triple-Switch Triple-Mode High Step-Up DC–DC Converter

    by Vafa Marzang, Seyed Majid Hashemzadeh, Peyman Alavi, Arash Khoshkbar-Sadigh, Seyed Hossein Hosseini, Muhammad Zeeshan Malik

    In this article, a new triple-switch triple-mode (TS-TM) high step-up dc–dc converter is proposed. The proposed converter consists of three switches, four diodes, two magnetically coupled inductors, and three capacitors. This converter can provide a high voltage conversion ratio with high power efficiency and low voltage stress across the power semiconductor components. Due to the low voltage stresses of the power semiconductors and implementing the coupled inductors technique, the proposed converter is a low-cost and high-efficient structure in comparison to the other similar TS-TM structures. In order to clarify the advantages of the proposed converter, the required mathematical calculations and comparison results with similar converters are presented. Also, a novel TS-TM with transformer is proposed to overcome the electromagnetic interface problems. Furthermore, a 500 W experimental prototype is built and its performance with different values of duty cycles is tested to prove the claimed features of the proposed converter. A total of 94.5% maximum power efficiency of the assembled prototype has been obtained at 260 W output power.


  • Simple Active Capacitor Voltage Balancing Method Without Cost Function Optimization for Seven-Level Full-Bridge Flying-Capacitor-Multicell Inverters

    by Arash Khoshkbar-Sadigh, Vahid Dargahi, Ramin Rahimzadeh Khorasani, Keith A. Corzine, Ebrahim Babaei

    Flying-capacitor (FC) based multicell inverters have recently drawn more attentions due to their outstanding performances. In this paper, a new approach to actively control the FC voltages in seven-level full-bridge FC multicell (FCM) inverters is presented. In the proposed method, first, the output current's direction and voltage of the FCs are measured and are interpreted into logic variables. Next, these logic variables are fed into a set of equations, named as logic-equations, to achieve two goals: 1) to adjust the voltage of the FCs at their reference values; 2) to generate the required voltage level at the output which is determined by pulse-width-modulation (PWM) unit. Since the proposed method does need neither the optimization of cost functions nor the utilization of proportional integral (PI) controllers, it is straightforward and simple to be implemented, specifically for the FC-based industrial inverters. To verify the performance and feasibility of the proposed logic equations-based active voltage balancing method, the simulation and experimental results obtained from a seven-level full-bridge FCM inverter are provided. The proposed method is validated under the transient conditions such as variations of modulation index and the dynamic changes of dc link voltage to demonstrate its robustness and performance.


  • Active Voltage Balancing Control of a Seven-Level Hybrid Multilevel Converter Topology

    by Vahid Dargahi, Arash Khoshkbar Sadigh, Ramin Rahimzadeh Khorasani, Jose Rodriguez

    The series connection of a standard three-level active neutral-point-clamped (ANPC) inverter and two cascaded H-bridge (CHB) modules comprising the flying capacitors (FCs) instead of the isolated dc voltage sources forms a seven-level hybrid topology that is referred to as improved ANPC (I-ANPC) converter. This article proposes an active voltage balancing technique for control of this hybrid multilevel inverter. The suggested method is based on a set of effortless logic equations that aim to stabilize the FC voltages within the CHB modules at their requisite reference values as well as to control the output voltage of the overall hybrid converter based on the phase-shifted-carrier pulsewidth modulation strategy. The experimental results obtained from a single-phase I-ANPC inverter's prototype are presented to validate the proposed control technique and its simple logic equations.