Peyman Alavi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Peyman Alavi has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Arash Khoshkbar-Sadigh
School of Electrical Engineering and Computer Science, Pennsylvania State University, University Park, PA, USA
3 shared publications - Vafa Marzang
Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, USA
3 shared publications - Ebrahim Babaei
Faculty of Electrical and Computer Engineering, University of Tabriz, Tabriz, Iran
2 shared publications - Iman Talebian
Faculty of Electrical and Computer Engineering, University of Tabriz, Tabriz, Iran
2 shared publications - Parham Mohseni
Department of Electrical Power Engineering and Mechatronics, Tallinn University of Technology, Tallinn, Estonia
2 shared publications - Seyed Majid Hashemzadeh
College of Electrical Engineering and New Energy, China Three Gorges University, Yichang, China
2 shared publications
Latest Publications
- Open Access
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 24112-24127
A New Single DC Source Five-Level Boost Inverter Applicable to Grid-Tied Systems
In this paper, a single source five-level boost inverter has been proposed and analyzed. The proposed structure includes a five-level inverter and a single-input multi-output (SIMO) boost converter. In this structure, the DC link voltage has been controlled by controlling the implemented DC-DC boost converter. In addition, the inverter switching pattern has been obtained based on the pick current control (PCC) method. In order to test and prove the performance of the proposed structure, this system is tested with the local grid. Since the active and reactive powers have been controlled based on the PCC method, the generated energy in a renewable energy source can be transferred to the local grid with a controlled and high-quality current. In this paper, the proposed structure has been introduced and its operation in different modes has been analyzed completely. Furthermore, the design considerations of the required elements have been investigated. Also, the power loss analysis and the comparison results of the proposed converter with other similar structures have been presented. Finally, in order to test the practical performance of the proposed structure and prove the theoretical analysis, a 620 W laboratory prototype of this structure has been assembled and its performance with the local grid has been tested.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 24112-24127
Open AccessA New Single DC Source Five-Level Boost Inverter Applicable to Grid-Tied Systems
In this paper, a single source five-level boost inverter has been proposed and analyzed. The proposed structure includes a five-level inverter and a single-input multi-output (SIMO) boost converter. In this structure, the DC link voltage has been controlled by controlling the implemented DC-DC boost converter. In addition, the inverter switching pattern has been obtained based on the pick current control (PCC) method. In order to test and prove the performance of the proposed structure, this system is tested with the local grid. Since the active and reactive powers have been controlled based on the PCC method, the generated energy in a renewable energy source can be transferred to the local grid with a controlled and high-quality current. In this paper, the proposed structure has been introduced and its operation in different modes has been analyzed completely. Furthermore, the design considerations of the required elements have been investigated. Also, the power loss analysis and the comparison results of the proposed converter with other similar structures have been presented. Finally, in order to test the practical performance of the proposed structure and prove the theoretical analysis, a 620 W laboratory prototype of this structure has been assembled and its performance with the local grid has been tested.
- 28 March 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (5) , 3119-3135
A simple soft-switched buck converter without implementing auxiliary switch
- 28 March 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (5) , 3119-3135
A simple soft-switched buck converter without implementing auxiliary switch
- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6899-6912
Analysis, Design, and Investigation of a Soft-Switched Buck Converter With High Efficiency
In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.
- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6899-6912
Analysis, Design, and Investigation of a Soft-Switched Buck Converter With High Efficiency
In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (8) , 8015-8027
A Modified Triple-Switch Triple-Mode High Step-Up DC–DC Converter
In this article, a new triple-switch triple-mode (TS-TM) high step-up dc–dc converter is proposed. The proposed converter consists of three switches, four diodes, two magnetically coupled inductors, and three capacitors. This converter can provide a high voltage conversion ratio with high power efficiency and low voltage stress across the power semiconductor components. Due to the low voltage stresses of the power semiconductors and implementing the coupled inductors technique, the proposed converter is a low-cost and high-efficient structure in comparison to the other similar TS-TM structures. In order to clarify the advantages of the proposed converter, the required mathematical calculations and comparison results with similar converters are presented. Also, a novel TS-TM with transformer is proposed to overcome the electromagnetic interface problems. Furthermore, a 500 W experimental prototype is built and its performance with different values of duty cycles is tested to prove the claimed features of the proposed converter. A total of 94.5% maximum power efficiency of the assembled prototype has been obtained at 260 W output power.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (8) , 8015-8027
A Modified Triple-Switch Triple-Mode High Step-Up DC–DC Converter
In this article, a new triple-switch triple-mode (TS-TM) high step-up dc–dc converter is proposed. The proposed converter consists of three switches, four diodes, two magnetically coupled inductors, and three capacitors. This converter can provide a high voltage conversion ratio with high power efficiency and low voltage stress across the power semiconductor components. Due to the low voltage stresses of the power semiconductors and implementing the coupled inductors technique, the proposed converter is a low-cost and high-efficient structure in comparison to the other similar TS-TM structures. In order to clarify the advantages of the proposed converter, the required mathematical calculations and comparison results with similar converters are presented. Also, a novel TS-TM with transformer is proposed to overcome the electromagnetic interface problems. Furthermore, a 500 W experimental prototype is built and its performance with different values of duty cycles is tested to prove the claimed features of the proposed converter. A total of 94.5% maximum power efficiency of the assembled prototype has been obtained at 260 W output power.
- 14 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (1) , 323-335
Ultrahigh Voltage Gain DC–DC Boost Converter With ZVS Switching Realization and Coupled Inductor Extendable Voltage Multiplier Cell Techniques
In this article, a novel ultrahigh voltage gain dc–dc boost converter with expandable diode-capacitor voltage multiplier (VM) cells is presented. The diode-capacitor VM cells and coupled inductors are employed in the presented topology to provide a higher voltage gain. Also, the main and the auxiliary power switches of the presented converter operate with zero voltage switching. The coupled inductors' leakage inductances control the rates of the current drop in the voltage multiplier diodes, which decreases their reverse recovery losses markedly. Moreover, the voltage stresses on all capacitors and semiconductors are reduced significantly. In this converter, the number of voltage multiplier cells, and the coupled inductors turn ratios provide three degrees of design freedom. These degrees of freedom are used to set the desired voltage stresses of the semiconductors within the desired range and to provide a high voltage gain at optimum duty cycles. The design and theoretical analysis of the presented converter are discussed. Finally, the performance of the presented converter is validated using a 500 W, 40 V/380 V laboratory prototype converter, and the experimental results confirm the theoretical calculation.
- 14 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (1) , 323-335
Ultrahigh Voltage Gain DC–DC Boost Converter With ZVS Switching Realization and Coupled Inductor Extendable Voltage Multiplier Cell Techniques
In this article, a novel ultrahigh voltage gain dc–dc boost converter with expandable diode-capacitor voltage multiplier (VM) cells is presented. The diode-capacitor VM cells and coupled inductors are employed in the presented topology to provide a higher voltage gain. Also, the main and the auxiliary power switches of the presented converter operate with zero voltage switching. The coupled inductors' leakage inductances control the rates of the current drop in the voltage multiplier diodes, which decreases their reverse recovery losses markedly. Moreover, the voltage stresses on all capacitors and semiconductors are reduced significantly. In this converter, the number of voltage multiplier cells, and the coupled inductors turn ratios provide three degrees of design freedom. These degrees of freedom are used to set the desired voltage stresses of the semiconductors within the desired range and to provide a high voltage gain at optimum duty cycles. The design and theoretical analysis of the presented converter are discussed. Finally, the performance of the presented converter is validated using a 500 W, 40 V/380 V laboratory prototype converter, and the experimental results confirm the theoretical calculation.
- 27 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10489-10500
A High Step-Up Nonisolated DC–DC Converter With Flexible Voltage Gain
In this paper, a high step-up non-isolated DC-DC converter is proposed to provide high voltage-gain with low voltage-stress on semiconductors. The main feature of the proposed structure is its flexibility in providing constant output voltages with a reasonable range of voltage stress. This flexibility of the voltage-gain is achieved by different combinations of duty cycles. Also, this feature improves the efficiency of the proposed converter. This structure consists of three switches, two inductors, three capacitors and four diodes. In this paper, description of continuous conduction mode (CCM), discontinuous conduction mode (DCM), boundary condition mode (BCM), non-ideal model, and control method are presented. Comparisons between the proposed converter and other related structures show that in this converter, the voltage gain is improved and semiconductors voltage stresses are reduced. In order to verify the mathematical analysis, a 500W laboratory prototype of the proposed converter is built and its experimental results are investigated completely.
- 27 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10489-10500
A High Step-Up Nonisolated DC–DC Converter With Flexible Voltage Gain
In this paper, a high step-up non-isolated DC-DC converter is proposed to provide high voltage-gain with low voltage-stress on semiconductors. The main feature of the proposed structure is its flexibility in providing constant output voltages with a reasonable range of voltage stress. This flexibility of the voltage-gain is achieved by different combinations of duty cycles. Also, this feature improves the efficiency of the proposed converter. This structure consists of three switches, two inductors, three capacitors and four diodes. In this paper, description of continuous conduction mode (CCM), discontinuous conduction mode (DCM), boundary condition mode (BCM), non-ideal model, and control method are presented. Comparisons between the proposed converter and other related structures show that in this converter, the voltage gain is improved and semiconductors voltage stresses are reduced. In order to verify the mathematical analysis, a 500W laboratory prototype of the proposed converter is built and its experimental results are investigated completely.