Abdelbaset R. H. Midawi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Abdelbaset R. H. Midawi has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Elliot Biro
University of Waterloo
8 shared publications - Mohammad Shojaee
University of Waterloo
8 shared publications - Hassan Ghassemi-Armaki
General Motors R&D, Manufacturing Systems Research Laboratory
4 shared publications - Oleksii Sherepenko
Institute of Materials and Joining Technology, Otto von Guericke University Magdeburg, 39106 Magdeburg, Germany
4 shared publications - Dileep Chandran Ramachandran
University of Waterloo
3 shared publications M. Worswick
3 shared publications
Latest Publications
- Open Access
- 15 May 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (7) , 1178-1184
Effect of Paint Baking Treatment on Mechanical Properties of Resistance Spot Welded Q&P 980 Steel
This study investigates the impact of paint baking on the macro and micro-mechanical properties of resistance spot welds in quenched and partitioned 980 steels. It is observed that paint baking enhances both peak load and energy absorption during cross-tension tests, as indicated by load-displacement curves. Four different regions were identified from the load-displacement curves after paint baking. An intriguing observation was a quick increase in the loading rate following a prior decrease, attributed to change in crack propagation behavior rather than improved work hardening. The study further simulated the upper-critical heat-affected zone using a Gleeble thermo-mechanical simulator to evaluate flow strength and work hardening. The Kocks-Mecking strain-hardening model was employed to analyze work hardening behavior in the studied conditions.
- 15 May 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (7) , 1178-1184
Open AccessEffect of Paint Baking Treatment on Mechanical Properties of Resistance Spot Welded Q&P 980 Steel
This study investigates the impact of paint baking on the macro and micro-mechanical properties of resistance spot welds in quenched and partitioned 980 steels. It is observed that paint baking enhances both peak load and energy absorption during cross-tension tests, as indicated by load-displacement curves. Four different regions were identified from the load-displacement curves after paint baking. An intriguing observation was a quick increase in the loading rate following a prior decrease, attributed to change in crack propagation behavior rather than improved work hardening. The study further simulated the upper-critical heat-affected zone using a Gleeble thermo-mechanical simulator to evaluate flow strength and work hardening. The Kocks-Mecking strain-hardening model was employed to analyze work hardening behavior in the studied conditions.
- 20 March 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (2) , 231-246
Modeling and Prediction of a 3G-980HF Spot Weld Shear Strength Using Response Surface Methodology
- 20 March 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (2) , 231-246
Modeling and Prediction of a 3G-980HF Spot Weld Shear Strength Using Response Surface Methodology
- Open Access
Prediction of Mechanical Properties in the Sub-Critical Heat Affected Zone of AHSS Spot Welds Using Gleeble Thermal Simulator and Hollomon-Jaffe Model
Measuring the mechanical properties of weld Heat Affected Zone (HAZ) remains one of the main challenges in the failure analysis of spot-welded components. Due to the small size of the HAZ and variation in the temperature history, different peak temperatures and cooling rates impose a range of phase transformations across the resistance spot weld. Among the HAZ sub-regions, the sub-critical HAZ (SCHAZ), which experiences temperatures below AC1 (350–650 °C), usually shows a reduction in the hardness in most of the modern AHSS grades due to the martensite tempering phenomenon. SCHAZ softening may lead to strain localization during loading. Therefore, it is important to characterize the local properties of the SCHAZ region to accurately predict RSW failure. However, it is not feasible to extract standard mechanical test specimens out of the SCHAZ of the spot-welded structure due to its small size. In this work, the SCHAZ of the spot weld for two AHSS, 3G-980 and PHS-1500, was simulated using a Gleeble® (Dynamic Systems Inc., 323 NY-355, Poestenkill, NY 12140, USA) 3500 thermo-mechanical simulator. An in-situ high-speed IR thermal camera was used to measure the entire temperature field during the Gleeble heat-treatment process, which allowed for the visualization of the temperature distribution in the gauge area. The temperature and hardness data were fit to a Hollomon-Jaffe (HJ) model, which enables hardness prediction in the SCHAZ at any given temperature and time. Using the HJ model, a heat treatment schedule for each material was chosen to produce samples with hardness and microstructure matching the SCHAZ within actual spot weld coupons. Tensile specimens were machined from the coupons heat treated using simulated heat treatment schedules, and mechanical testing was performed. The results showed that the 3G-980 SCHAZ has a slight increase in yield strength and tensile strength, compared to the base metal, due to the formation of fine carbides within the microstructure. In contrast, the SCHAZ of PHS-1500 showed a significant reduction in the yield and tensile strength with yield point elongation behavior due to the reduction of the martensite phase and an increase in carbide formation due to the tempering process.
Open AccessPrediction of Mechanical Properties in the Sub-Critical Heat Affected Zone of AHSS Spot Welds Using Gleeble Thermal Simulator and Hollomon-Jaffe Model
Measuring the mechanical properties of weld Heat Affected Zone (HAZ) remains one of the main challenges in the failure analysis of spot-welded components. Due to the small size of the HAZ and variation in the temperature history, different peak temperatures and cooling rates impose a range of phase transformations across the resistance spot weld. Among the HAZ sub-regions, the sub-critical HAZ (SCHAZ), which experiences temperatures below AC1 (350–650 °C), usually shows a reduction in the hardness in most of the modern AHSS grades due to the martensite tempering phenomenon. SCHAZ softening may lead to strain localization during loading. Therefore, it is important to characterize the local properties of the SCHAZ region to accurately predict RSW failure. However, it is not feasible to extract standard mechanical test specimens out of the SCHAZ of the spot-welded structure due to its small size. In this work, the SCHAZ of the spot weld for two AHSS, 3G-980 and PHS-1500, was simulated using a Gleeble® (Dynamic Systems Inc., 323 NY-355, Poestenkill, NY 12140, USA) 3500 thermo-mechanical simulator. An in-situ high-speed IR thermal camera was used to measure the entire temperature field during the Gleeble heat-treatment process, which allowed for the visualization of the temperature distribution in the gauge area. The temperature and hardness data were fit to a Hollomon-Jaffe (HJ) model, which enables hardness prediction in the SCHAZ at any given temperature and time. Using the HJ model, a heat treatment schedule for each material was chosen to produce samples with hardness and microstructure matching the SCHAZ within actual spot weld coupons. Tensile specimens were machined from the coupons heat treated using simulated heat treatment schedules, and mechanical testing was performed. The results showed that the 3G-980 SCHAZ has a slight increase in yield strength and tensile strength, compared to the base metal, due to the formation of fine carbides within the microstructure. In contrast, the SCHAZ of PHS-1500 showed a significant reduction in the yield and tensile strength with yield point elongation behavior due to the reduction of the martensite phase and an increase in carbide formation due to the tempering process.
- 4 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 886
Improvement of the mechanical performance of ZnAlMg coated steel brazed joints through precipitation-based strengthening
- 4 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 886
Improvement of the mechanical performance of ZnAlMg coated steel brazed joints through precipitation-based strengthening
- Open Access
- 24 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 22-31
Mitigating the influence of industrially relevant disturbances on LME severity of dissimilar resistance spot welded advanced high-strength steels
- 24 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 22-31
Open AccessMitigating the influence of industrially relevant disturbances on LME severity of dissimilar resistance spot welded advanced high-strength steels
- 5 July 2023
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 180, 160-173
Revealing microstructural evolution and mechanical properties of resistance spot welded NiTi-stainless steel with Ni or Nb interlayer
- 5 July 2023
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 180, 160-173
Revealing microstructural evolution and mechanical properties of resistance spot welded NiTi-stainless steel with Ni or Nb interlayer
- Open Access
Effect of Liquid Metal Embrittlement Indent Cracks on Zinc Coated 3rd Generation AHSS Mechanical Performance
Third-generation advanced high-strength steels (3G-AHSS) are typically galvanized to prevent corrosion of the outer body structure. However, the zinc coating on the surface, combined with the locally elevated temperatures generated during the resistance spot welding (RSW) process, can provide the prerequisites for liquid metal embrittlement (LME). This work uses two strategies to control LME crack formation: current pulsation and varying the electrode geometry. These two methods were compared to a baseline welding schedule for a 3G-980-GI coated AHSS. The effectiveness of each method was discussed in terms of the overall weld cracking index and local cracking index. The results showed that increasing the current pulses results in a slower energy input into the weld, which can help to reduce LME crack formation. Introducing more pulses (five to seven pulses) reduced LME crack formation while maintaining the same welding time. Regarding the electrode geometry, the results showed an increase in LME cracking index for currents below the expulsion level Imax-10% when the electrode face diameter increased, whereas at the current level Imax-200A, the electrode radius was the most important factor to control LME crack index. For the current level above the expulsion, Imax+10%, a drastic decrease in the LME cracking index was observed when a large electrode surface diameter was used. The electrode radius was not a significant factor in controlling LME. The mechanical properties of selected conditions were examined using the lap shear test and the results showed no significant effect of LME cracks on the shear tensile strength. The location of the failure indicated that most of the cracks are located in the indented area (type A), which does not influence the lap shear strength.
Open AccessEffect of Liquid Metal Embrittlement Indent Cracks on Zinc Coated 3rd Generation AHSS Mechanical Performance
Third-generation advanced high-strength steels (3G-AHSS) are typically galvanized to prevent corrosion of the outer body structure. However, the zinc coating on the surface, combined with the locally elevated temperatures generated during the resistance spot welding (RSW) process, can provide the prerequisites for liquid metal embrittlement (LME). This work uses two strategies to control LME crack formation: current pulsation and varying the electrode geometry. These two methods were compared to a baseline welding schedule for a 3G-980-GI coated AHSS. The effectiveness of each method was discussed in terms of the overall weld cracking index and local cracking index. The results showed that increasing the current pulses results in a slower energy input into the weld, which can help to reduce LME crack formation. Introducing more pulses (five to seven pulses) reduced LME crack formation while maintaining the same welding time. Regarding the electrode geometry, the results showed an increase in LME cracking index for currents below the expulsion level Imax-10% when the electrode face diameter increased, whereas at the current level Imax-200A, the electrode radius was the most important factor to control LME crack index. For the current level above the expulsion, Imax+10%, a drastic decrease in the LME cracking index was observed when a large electrode surface diameter was used. The electrode radius was not a significant factor in controlling LME. The mechanical properties of selected conditions were examined using the lap shear test and the results showed no significant effect of LME cracks on the shear tensile strength. The location of the failure indicated that most of the cracks are located in the indented area (type A), which does not influence the lap shear strength.
- Open Access
- 22 January 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 1458-1470
Influence of expulsion and heat extraction resulting from changes to electrode force on liquid metal embrittlement during resistance spot welding
- 22 January 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 1458-1470
Open AccessInfluence of expulsion and heat extraction resulting from changes to electrode force on liquid metal embrittlement during resistance spot welding
- Open Access
- 30 November 2022
- Published by Elsevier in Forces in Mechanics
- Vol. 9
A novel technique to measure the local mechanical properties of third generation advanced high strength steel resistance spot welds
- 30 November 2022
- Published by Elsevier in Forces in Mechanics
- Vol. 9
Open AccessA novel technique to measure the local mechanical properties of third generation advanced high strength steel resistance spot welds