Vincenzo La Rocca
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vincenzo La Rocca has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Alessandro Busacca
University of Palermo
1 shared publication Alfonso C. Cino
DEIM, University of Palermo, Viale delle Scienze, Building 9, 90128 Palermo, Italy
1 shared publication- Antonino Parisi
Department of Engineering, University of Palermo, Viale delle Scienze, Building 9, 90128 Palermo, Italy
1 shared publication - Edoardo Moreci
Dipartimento di Energia, Ingegneria dell'Informazione e Modelli Matematici - DEIM, University of Palermo, Palermo, Italy
1 shared publication - Francesco Guarino
Department of Engineering, University of Palermo, Viale delle Scienze, Building 9, 90128 Palermo, Italy
1 shared publication - Giovanni Cipriani
University of Palermo, Palermo, Italy
1 shared publication
Latest Publications
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Energy and economic assessment of a small domestic wind turbine in Palermo
The cost effectiveness of micro-wind technology is closely linked to the annual energy production plants, which strongly depends on the wind characteristics and on the morphological properties of the installation site. The power curve of a wind turbine, supplied by manufacturers, characterizes the theoretical energy performance that it should have at a particular site. The behavior of a wind turbine in the field is affected by the speed but also by wind direction variations. At each change of direction and speed, the turbine will try to adapt to new conditions and the phase transition negatively influences the energy production. In order to experimentally confirm what above mentioned, the authors have built up a test facility and started a monitoring campaign in the urban area of Palermo. In particular, a micro wind turbine and a weather station were installed at the solar laboratory of DEIM. Thanks to data monitoring was possible a climate characterization of the site, and the evaluation of the experimental power curve of the turbine. The experimental data were discussed and compared to the manufactured data.
- 1 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Energy and economic assessment of a small domestic wind turbine in Palermo
The cost effectiveness of micro-wind technology is closely linked to the annual energy production plants, which strongly depends on the wind characteristics and on the morphological properties of the installation site. The power curve of a wind turbine, supplied by manufacturers, characterizes the theoretical energy performance that it should have at a particular site. The behavior of a wind turbine in the field is affected by the speed but also by wind direction variations. At each change of direction and speed, the turbine will try to adapt to new conditions and the phase transition negatively influences the energy production. In order to experimentally confirm what above mentioned, the authors have built up a test facility and started a monitoring campaign in the urban area of Palermo. In particular, a micro wind turbine and a weather station were installed at the solar laboratory of DEIM. Thanks to data monitoring was possible a climate characterization of the site, and the evaluation of the experimental power curve of the turbine. The experimental data were discussed and compared to the manufactured data.
- Open Access
- 1 November 2015
- Published by Elsevier in Energy Procedia
- Vol. 78, 1708-1713
Phase Change Materials Applications to Optimize Cooling Performance of Buildings in the Mediterranean Area: A Parametric Analysis
- 1 November 2015
- Published by Elsevier in Energy Procedia
- Vol. 78, 1708-1713
Open AccessPhase Change Materials Applications to Optimize Cooling Performance of Buildings in the Mediterranean Area: A Parametric Analysis
- Open Access
- 1 January 2015
- Published by Wiley in International Journal of Photoenergy
- Vol. 2015, 1-9
Graded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells
We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters—characteristic of such devices—with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%).
- 1 January 2015
- Published by Wiley in International Journal of Photoenergy
- Vol. 2015, 1-9
Open AccessGraded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells
We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters—characteristic of such devices—with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%).