Sukanta Bhowmick
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sukanta Bhowmick has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet T. Alpas
Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Avenue, Windsor, ON N9B 3P4, Canada
7 shared publications - Behzad Eskandari
Mechanical Automotive and Materials Engineering Department, University of Windsor, Windsor, Canada
4 shared publications - Faiz Muhaffel
Istanbul Technical University
2 shared publications Girish Krishnamurthy
Mechanical Automotive and Materials Engineering Department, University of Windsor, Windsor, Canada
1 shared publication- Huseyin Cimenoglu
Department of Metallurgical and Materials Engineering, Istanbul Technical University, Istanbul 34467, Turkey
1 shared publication - Huseyin Cimenoglu
Department of Metallurgical and Materials Engineering, Istanbul Technical University, Istanbul, Turkey
1 shared publication
Latest Publications
- Open Access
- 28 December 2023
- Published by MDPI AG in Lubricants
- Vol. 12 (1) , 9
Tribological Performance of a Plasma Electrolytic Oxidation-Coated Mg Alloy in Graphene-Incorporated Ethanol
This study investigated the friction and wear characteristics of a plasma electrolytic oxidation (PEO)-coated Mg–Al alloy (AZ31) in sliding contact against steel using graphene nanoplatelets (GNPs) containing ethanol as a lubricant. The results revealed that the typically high coefficient of friction (COF) of PEO-coated surfaces under dry sliding (0.74) was notably reduced to 0.18 during the sliding tests conducted in GNP-free ethanol. When the ethanol contained 5 × 10−4 wt.% GNPs, the COF of the uncoated AZ31 alloy further dropped to 0.17. The PEO-coated surfaces achieved a significantly lower COF of 0.07 and demonstrated a marked reduction in wear rate, attributed to the formation of a tribolayer incorporating graphene. These findings highlight the significant potential of GNP-incorporated ethanol to improve the tribological performance of PEO-coated AZ31, presenting a promising avenue for advancing lightweight, sustainable, and efficient automotive technologies.
- 28 December 2023
- Published by MDPI AG in Lubricants
- Vol. 12 (1) , 9
Open AccessTribological Performance of a Plasma Electrolytic Oxidation-Coated Mg Alloy in Graphene-Incorporated Ethanol
This study investigated the friction and wear characteristics of a plasma electrolytic oxidation (PEO)-coated Mg–Al alloy (AZ31) in sliding contact against steel using graphene nanoplatelets (GNPs) containing ethanol as a lubricant. The results revealed that the typically high coefficient of friction (COF) of PEO-coated surfaces under dry sliding (0.74) was notably reduced to 0.18 during the sliding tests conducted in GNP-free ethanol. When the ethanol contained 5 × 10−4 wt.% GNPs, the COF of the uncoated AZ31 alloy further dropped to 0.17. The PEO-coated surfaces achieved a significantly lower COF of 0.07 and demonstrated a marked reduction in wear rate, attributed to the formation of a tribolayer incorporating graphene. These findings highlight the significant potential of GNP-incorporated ethanol to improve the tribological performance of PEO-coated AZ31, presenting a promising avenue for advancing lightweight, sustainable, and efficient automotive technologies.
- Open Access
Low Friction and High Wear Resistance of Plasma Electrolytic Oxidation (PEO)-Coated AZ31 Mg Alloy Sliding against Hydrogenated DLC (a-C-H) at Elevated Temperatures
Plasma electrolytic oxidation (PEO) treatment of Mg alloys improves their wear resistance by increasing their surface hardness, but also leads to high coefficient of friction (COF) values. The sliding counterfaces and the conditions under which PEO-coated Mg alloys operate affect their COFs. PEO-coated AZ31 alloy sliding against hydrogenated DLC (a-C-H) coated steel yields a low COF of 0.13 under the ambient conditions. The current study investigates the effect of the test temperature on the tribological behavior of PEO-coated AZ31 Mg samples sliding against the a-C-H coated counterface at temperatures up to 300 °C. According to the COF vs. wear rate diagram constructed in the temperature range of 25–250 °C, lower COF values and wear rates were exhibited by PEO-coated AZ31 sliding against a-C-H compared to uncoated AZ31 sliding against a-C-H, and PEO coated AZ31 sliding against an uncoated ASTM 52100 steel. The PEO-coated AZ31 produced the lowest COF of 0.03 at 200 °C. The application of PEO to the Mg alloy automotive cylinder bores running against DLC-coated piston rings and/or PEO-coated Mg alloy pistons running against DLC-coated bores could provide a new approach for the prevention of seizure and hot scuffing in lightweight engines in the temperature range between 150–250 °C.
Open AccessLow Friction and High Wear Resistance of Plasma Electrolytic Oxidation (PEO)-Coated AZ31 Mg Alloy Sliding against Hydrogenated DLC (a-C-H) at Elevated Temperatures
Plasma electrolytic oxidation (PEO) treatment of Mg alloys improves their wear resistance by increasing their surface hardness, but also leads to high coefficient of friction (COF) values. The sliding counterfaces and the conditions under which PEO-coated Mg alloys operate affect their COFs. PEO-coated AZ31 alloy sliding against hydrogenated DLC (a-C-H) coated steel yields a low COF of 0.13 under the ambient conditions. The current study investigates the effect of the test temperature on the tribological behavior of PEO-coated AZ31 Mg samples sliding against the a-C-H coated counterface at temperatures up to 300 °C. According to the COF vs. wear rate diagram constructed in the temperature range of 25–250 °C, lower COF values and wear rates were exhibited by PEO-coated AZ31 sliding against a-C-H compared to uncoated AZ31 sliding against a-C-H, and PEO coated AZ31 sliding against an uncoated ASTM 52100 steel. The PEO-coated AZ31 produced the lowest COF of 0.03 at 200 °C. The application of PEO to the Mg alloy automotive cylinder bores running against DLC-coated piston rings and/or PEO-coated Mg alloy pistons running against DLC-coated bores could provide a new approach for the prevention of seizure and hot scuffing in lightweight engines in the temperature range between 150–250 °C.
- 1 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (5-6) , 3077-3101
Turning of Inconel 718 using liquid nitrogen: multi-objective optimization of cutting parameters using RSM
- 1 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (5-6) , 3077-3101
Turning of Inconel 718 using liquid nitrogen: multi-objective optimization of cutting parameters using RSM
- Open Access
- 1 November 2021
- Published by Elsevier in Advances in Industrial and Manufacturing Engineering
- Vol. 3
Characterization of galling during dry and lubricated punching of AA5754 sheet
- 1 November 2021
- Published by Elsevier in Advances in Industrial and Manufacturing Engineering
- Vol. 3
Open AccessCharacterization of galling during dry and lubricated punching of AA5754 sheet
- 14 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (1-2) , 1-14
Flooded drilling of Inconel 718 using graphene incorporating cutting fluid
- 14 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (1-2) , 1-14
Flooded drilling of Inconel 718 using graphene incorporating cutting fluid
- 10 November 2020
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 15 (4) , 229-242
Effect of WS2 particles in cutting fluid on tribological behaviour of Ti–6Al–4V and on its machining performance
Tribological behaviour of Ti–6Al–4V alloy sliding against WC-Co was evaluated by employing WS2 nanoparticles blended in a cutting fluid used for machining of this alloy. Pin-on disk tests were carried out under boundary-lubricated condition using a cutting fluid (70% water and 30% oil) blended with WS2 nanoparticles (CF + WS2). When a cutting fluid with ≥ 0.5 wt.% WS2 was used, the COF of the tribosystem was reduced compared to CF + 0%WS2. The lowest COF of 0.05 was obtained when 1.0 wt.% WS2 was used. Low and stable COF values were accompanied by the formation of a tribolayer incorporating WS2 and WO3 on the WC-Co surfaces. During orthogonal machining of Ti–6Al–4V using CF + 1.0%WS2, a tribolayer with the similar composition was formed on the cutting edge of the WC-Co tool and the average cutting force was reduced by 35% compared to cutting with CF + 0%WS2. Machining with CF + 1.0%WS2 produced thinner chips. Other improvements in machining performance attained using CF + 1.0%WS2 included reduction of adhesive wear on the tool and a lower roughness of the machined surface. GRAPHICAL ABSTRACT
- 10 November 2020
- Published by SAGE Publications in Tribology - Materials, Surfaces & Interfaces
- Vol. 15 (4) , 229-242
Effect of WS2 particles in cutting fluid on tribological behaviour of Ti–6Al–4V and on its machining performance
Tribological behaviour of Ti–6Al–4V alloy sliding against WC-Co was evaluated by employing WS2 nanoparticles blended in a cutting fluid used for machining of this alloy. Pin-on disk tests were carried out under boundary-lubricated condition using a cutting fluid (70% water and 30% oil) blended with WS2 nanoparticles (CF + WS2). When a cutting fluid with ≥ 0.5 wt.% WS2 was used, the COF of the tribosystem was reduced compared to CF + 0%WS2. The lowest COF of 0.05 was obtained when 1.0 wt.% WS2 was used. Low and stable COF values were accompanied by the formation of a tribolayer incorporating WS2 and WO3 on the WC-Co surfaces. During orthogonal machining of Ti–6Al–4V using CF + 1.0%WS2, a tribolayer with the similar composition was formed on the cutting edge of the WC-Co tool and the average cutting force was reduced by 35% compared to cutting with CF + 0%WS2. Machining with CF + 1.0%WS2 produced thinner chips. Other improvements in machining performance attained using CF + 1.0%WS2 included reduction of adhesive wear on the tool and a lower roughness of the machined surface. GRAPHICAL ABSTRACT