SKSerhii Koropchenko

Serhii Koropchenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Serhii Koropchenko has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Substantiating the rational parameters and operation modes for the hemp seed centrifugal dehuller

    by Viktor Sheichenko, Dmytro Petrachenko, Serhii Koropchenko, Ivan Rogovskii, Oleksandr Gorbenko, Mykhailo Volianskyi, Denys Sheichenko

    The object of research is technological processes, seeds of industrial hemp, and working bodies of the dehuller. A centrifugal-type device for crushing hemp seeds with a closed sector-type working body has been designed. Owing to this, the task related to seed dehulling was solved with a high level of efficiency in separating the seed coat from the kernel. The rational parameters for the dehuller have been substantiated: the diameter of the impeller is 162 mm, the gap between the impeller and the seed repelling panel is 80 mm, the frequency of rotation of the impeller is 2000 min–1. It was established that with the specified parameters and moisture content of the seeds within the limits of conditional (12.0–13.0 %), it is advisable to carry out dehulling process without preliminary separation of the seeds into fractions by width. It was established that an increase in seed size leads to a corresponding increase in the weight share of seed kernels. About 58.2 % of the main mass of seeds is the average fraction with a width of 2.5 to 3.0 mm. It was found that reducing the diameter of the impeller (from 236 mm to 162 mm) at a seed moisture content of 8.8 % improved the efficiency of dehulling. At a rotation frequency of the impeller of 2000 min–1, the highest total number of intact and destroyed kernels (23.23–29.33 %) was achieved for the two studied moistures. With an increase in seed moisture content from 8.8 % to 12.0 %, the number of dehulled kernels in the hempseed cake increased. It was noted that for seeds with a moisture content of 8.8 %, an increase in the gap led to a decrease in the dehulling efficiency for each of the three investigated seed fractions. The total number of dehulled kernels under such conditions decreased by 2.4–6.8 % and amounted to 16.4–26.9 %. For seeds with a moisture content of 12.0 %, an increase in the gap, on the contrary, increased the dehulling efficiency for each of the three investigated seed fractions. The total number of dehulled kernels for seeds of marked moisture increased within the range of 1.4–3.6 % and amounted to 27.4–31.0 % Об’єктом дослідження є технологічні процеси, насіння промислових конопель, робочі органи обрушувача. Розроблено пристрій відцентрового типу для обрушування насіння конопель із робочим органом закритого секторального типу. Завдяки цьому вирішено проблему обрушування насіння із високим рівнем ефективності відділення насіннєвої оболонки від ядра. Обгрунтовано раціональні параметри обрушувача: діаметр робочого колеса 162 мм, зазор між робочим колесом та відбивною декою 80 мм, частота обертання робочого колеса 2000 хв.-1. Встановлено, що за зазначених параметрів та вологості насіння в межах кондиційної (12,0–13,0 %) процес обрушування доцільно проводити без попереднього розділення насіння на фракції за шириною. Встановлено, що збільшення розмірів насіння призводить до відповідного зростання частки ваги насіннєвих ядер. Близько 58,2 % в основній масі насіння складає середня фракція шириною від 2,5 до 3,0 мм. Встановлено, що зменшення діаметру робочого колеса (від 236 мм до 162 мм) за вологості насіння 8,8 % підвищувало ефективність обрушування. За частоти обертання робочого колеса 2000 хв.-1 досягнуто найбільшу сумарну кількість цілих та зруйнованих ядер (23,23–29,33 %) для двох досліджуваних вологостей. Зі збільшенням вологості насіння від 8,8 % до 12,0 % кількість обрушених ядер в рушанці збільшувалося. Відзначено, що для насіння вологістю 8,8 % збільшення зазору призводило до зменшення ефективності обрушування для кожної з трьох досліджуваних фракцій насіння. Сумарна кількість обрушених ядер за таких умов зменшувалася в межах 2,4–6,8 % та складала 16,4–26,9 %. Для насіння вологістю 12,0 % збільшення зазору, навпаки, підвищувало ефективність обрушування для кожної з трьох досліджуваних фракцій насіння. Сумарна кількість обрушених ядер для насіння відміченої вологості збільшувалася в межах 1,4–3,6 % та складала 27,4–31,0 %


  • Open Access

    ВПЛИВ РОЗМІРУ ФРАКЦІЇ ТА ПАРАМЕТРІВ РОБОЧОГО ОБЛАДНАННЯ НА ОБРУШУВАННЯ НАСІННЯ ПРОМИСЛОВИХ КОНОПЕЛЬ

    by Д. О. Петраченко, С. П. Коропченко

    Предмет. Насіння промислових конопель різних фракцій, конструктивні параметри обрушувача та технологічні режими його роботи. Мета. Дослідження процесу обрушування в залежності від фізичних властивостей насіння конопель та конструктивних і технологічних параметрів обрушувача. Методи. Характеристики насіння визначали згідно з ДСТУ 4138-2002. Для обрушування насіння використовували розроблений відцентровий механізм. Змінними параметрами виступали: зазор між робочим колесом та відбійною декою (15, 40 мм); частота обертання робочого колеса (1500, 2000, 2500 хв.-1); фракція насіння за розміром – крупна (>3,0 мм), середня (2,5-3,0 мм), дрібна (<2,5 мм). Результати. Кожен з параметрів впливає на фракційний склад рушанки. Найважче обрушується дрібна фракція. Найефективнішим є обрушування крупної фракції насіння. Для всіх трьох розмірних фракцій збільшення зазору між робочим колесом і декою з 15 до 40 мм підвищує кількість обрушеного ядра. Збільшення частоти обертання робочого колеса неоднозначно впливає на процес. При збільшені частоти обертання робочого колеса з 1500 до 2000 хв-1 в рушанці спостерігається підвищення кількості обрушеного ядра. Подальше збільшення частоти обертання колеса до 2500 хв-1 зменшує кількість обрушеного ядра. При даній швидкості обертання обрушувач виконує функцію подрібнювача, що призводить до розмелення насіння. При величині зазору між робочим колесом і декою 40 мм та частоті обертання робочого колеса 2000 хв-1 обрушуючий механізм має оптимальні робочі параметри переробки для трьох фракцій насіння. Кращі результати обрушування одержали при величині зазору 40 мм і частоті обертання колеса 2000 хв-1: для дрібної фракції насіння кількість обрушеного ядра склала 16,47%, для середньої – 19,67%, для крупної – 21,90%. Сфера застосування результатів. Отримані дані будуть важливими для подальшого вдосконалення конструкції обрушуючого механізму, а також для розробки рекомендацій з оптимізації технологічного процесу переробки насіння промислових конопель на обрушене.

  • Open Access

    Devising technologies for harvesting hemp with belt threshers

    by Viktor Sheichenko, Vitaliy Shevchuk, Igor Dudnikov, Serhii Koropchenko, Viktor Dnes, Yuliia Skoriak, Volodymyr Skibchyk

    This paper reports the system of devised technologies for harvesting hemp with belt hemp threshers. It is proposed to form a roll of mowed hemp stems on a belt and tramp it to the field edge for further processing of stems. That makes it possible to significantly improve the efficiency of mechanized processes when harvesting and processing the entire biological harvest of hemp. Thus, the level of handling hemp production systems has been increased. At the same time, the management of the process of roll formation of hemp stems has been improved. The technology of hemp harvesting has been improved with the possibility of obtaining raw materials for long fiber and therapeutic preparations. Two-phase harvesting (for seeds and fiber) has been proposed to be implemented by using belt hemp threshers included in the stationary (semi-stationary) complexes. The possibility of preparing the combed hemp retted stalks by spreading them on materials of various types has been systematically substantiated. The influence of the thickness of a layer of hemp stalks spread out for the preparation of retted stalks on the timing of their preparation and fiber quality indicators has been investigated. It was established that in terms of the quality indicators of the produced fiber, the retted stalks from all experiments are properly aged while the efficiency of their processing for medium- and large-stalk fraction is high. The fibers produced in all experiments were characterized by purity, as well as high indicators of breaking load and handful length. As regards the linear density, the fibers’ values in all experimental variants exceeded the normative ones by 1.65‒2.64 times, which rendered them non-standard. An increase in the values of quality indicators has been established with the corresponding change, from 1 to 3 kilograms per meter, in the thickness of the layer of combed hemp stalks. The breaking load, under such conditions, increased by 16.6 %; the linear density, by 20 %; the content of shives, by 60 %; the «paw» content, by 12.5 %, the content of bast strands, by 10.8 %.


  • Open Access

    Developments of the Institute of Bast Crops in the direction of processing of industrial hemp seeds

    by Dmytro Petrachenko, Serhii Koropchenko

    Today, domestic hemp growing is raw material-oriented, which restrains the development of the industry and does not allow the integration of Ukrainian hemp growing into the international production system. The production of a high-quality finished product that can meet the needs of the country should be the priority direction of hemp production. As a scientific institution, the Institute of Bast Crops acts as an integral element of providing the hemp industry with modern developments that are potentially able to compete in the technology market. Using the achievements of the Institute in the direction of hemp seed processing will provide the domestic market with high-quality ready-made food products. The analysis of the products from industrial hemp seeds presented on the market allows us to distinguish two main directions of seed processing – into cold-pressed oil and crushed seeds. These products are used both independently and for the production of various hemp-containing products. In order to meet the needs of the market in cold-pressed hemp oil, the Institute of Bast Crops has developed a technology for obtaining oil using a simplified link of technological operations. The use of the developed technology makes it possible to process hemp seeds with a moisture content of 7-10% and obtain 16-22% filtered oil, the quality of which corresponds to the established norms, which is confirmed by the results of laboratory tests. To meet the needs of the market for crushed hemp seeds, a technology for obtaining crushed kernels has been developed, which includes the operations of crushing seeds, separation of husks by air, separation of husks on sieves. The developed technology provides for the processing of hemp seeds with a purity of 95.0-99.0% without additional calibration, with a moisture content of 6.0-13.0%, and allows obtaining 28.0-38.0% of the finished kernel with clogging up to 1.0%. The obtained crushed hemp seeds have high nutritional properties and meet the established norms, which are confirmed by the results of laboratory studies.

  • Open Access

    The results of the experimental development of a stand for shelling of industrial hemp seeds

    by Dmytro Petrachenko, Serhiy Koropchenko

    One of the promising directions for the use of industrial hemp seeds is the production of shelled seeds. The core of hemp seeds released from the inedible shell, as a standalone product, contains no digestible components, so it is a more valuable food product than the hemp seeds covered in the shell. The lack of technological equipment for destroying industrial hemp seeds impedes the development of this processing sector and makes research relevant in this area relevant. The effectiveness of oilseed crop destruction depends on the morphological and physico-mechanical properties of the directly treated seed. Finding the best method of destroying the seeds of industrial hemp is impossible without comparing the results of the efficiency of work of different means of operation of technical means. In the process of finding an effective method of collapse by the staff of the Engineering Research Department of the Institute of bast crops NAAS, among other things, the possibility of the collapse of hemp seeds by the method of repeated and single impact was explored. The principal possibility of shelling hemp seeds with the use of a machine type, where the multiple impact method is implemented, has been established. It is determined that this mechanism has several disadvantages. Excessive airflow is formed in the working chamber, which impedes the shelling process and affects the complexity of the structure. As the impeller rotates, the mechanism begins to act as a shredder: there is a significant increase in the fraction of ground seeds, that is, the seeds turn into oil dust. The basic possibility of demolition of hemp seeds by the method of focused single blow (centrifugal machines) is established. It is determined that this mechanism has several advantages, which simplifies the overall construction and principle of operation and is more promising for the sowing of hemp seeds. As a result, the design of a centrifugal stand for the shelling of hemp seeds was developed, the use of which allows to obtain 15.4% of the finished shelled kernel.

  • Open Access

    Results of the investigation of the active method of shelling of seeds of industrial hemp

    by Dmytro Petrachenko, Serhiy Koropchenko

    The article presents the results of studying the effectiveness of different methods of destruction of the seed coat, the establishment of the most promising design of the mechanism for the hemp seeds shelling.


  • Open Access

    Non-factory mechanical processing of hemp

    by Serhiy Koropchenko, Yuriy Mokher

    Based on the analysis of the state of the hemp breeding industry and primary processing plants, a conclusion was drawn on the feasibility of organizing mechanical processing of the stalk directly at small and medium-sized enterprises. Analyzed technical equipment for off-site processing.