ALAnne Lemnitzer

Anne Lemnitzer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Anne Lemnitzer has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluation of soil improvement surrounding drilled displacement piles through pre- and post-installation CPT data

    by Genesis Figueroa, Anne Lemnitzer

    Drilled displacement pile (DDP) installation has the potential to induce soil densification, and improve the soil response (e.g., shear strength and stiffness) around the borehole. An evaluation of pre- and post-pile installation soil properties surrounding newly installed DDPs has been carried out by interrogating data from 11 construction sites where Cone Penetration Tests (CPT) were performed before and after pile construction (i.e., CPT PRE and CPT POST ). CPT key measurements, i.e., tip resistance ( $$q_{{\text{c}}}$$ q c ) and sleeve friction ( $$f_{{\text{s}}}$$ f s ) were corrected for overburden stress to obtain the normalized cone resistance ( $$Q_{{{\text{tn}}}}$$ Q tn ) and normalized friction ratio ( $$F_{{\text{r}}}$$ F r ), and synthesized hereafter to obtain the Normalized CPT Soil Behavior Type Index ( $$I_{{\text{c}}}$$ I c ). An analysis of pre- and post-pile installation soil data suggests the change in CPT-based soil resistances to be dependent on the $$I_{{\text{c}}}$$ I c , q c , soil fines content ( FC ), and pile spacing. Sandy sites exhibited clearly traceable improvement of up to 4.5 times their initial resistance when original soil conditions fell within the SBTn zones 4 and 5, and FC remained below 30%. Soils above Robertson’s contractive-dilative (CD) line showed much less improvement potential (~ 1.5). Cohesive sites exhibited both: a reduction and improvement of resistance, with clear dependency on post-installation time elapse. Little to no improvement was observed for stratified soil profiles, regardless of their initial properties. Outside the pile group, a spatial analysis indicated that the largest improvement occurred within 1 pile diameter ( D ) from the pile, while little to no improvement was observed beyond 2 D. The greatest improvement was observed in CPT POST testing executed at the midpoint of a group arrangement of at least 3 piles with spacing of ≤ 3 D . Case studies further showed the improvement potential of silty soils ( $$I_{{\text{c}}}$$ I c ~ 2.6–2.9), and the improvement in interbedded cohesionless soil layers with a thickness of more than 1 m in mixed soil profiles, where drainage in upper and lower layers is available. The analysis of cohesionless soils in the SBTn chart demonstrates how this construction method can also be implemented to mitigate the risk of liquefaction of intermediate sands.

  • Open Access

    Morphologic interaction of bridges during high-energy flood events by the example of the flood of mid-July 2021 in the Ahr Valley, Germany

    by Stefanie Wolf, Lisa Burghardt, Nina Stark, Anton Ahlswede, Michael Gardner, Anne Lemnitzer, Holger Schüttrumpf

    In mid-July 2021, heavy rainfall led to severe flash floods in the Eifel-mountain region in western Germany. The Ahr River, a tributary to the Rhine River in Rhineland-Palatinate, was most severely affected. Discharges accumulated rapidly in the narrow valley and formed a fast-moving flood wave, leading to record-breaking water levels. High hydraulic forces in combination with driftwood and debris accumulation led to local back-up, and eventually failure of many bridges [1].The flood is proven to be a high-energy event that led to significant morphologic changes [2]. Besides lateral river course changes, severe local erosion was observed after the flood, and especially documented near bridges [3].The Ahr Valley is well suited for a case study on the morphologic interaction of bridges with high-energy floods, as around 75% of the 114 bridges were damaged or destroyed in 2021 [1]. In April 2022, bathymetry data was collected at two affected bridges. Further, selected bridges were monitored by drone surveys every six months, allowing us to investigate the morphologic development over the last two years.Besides bridge overtopping , pier scouring led to structural failure [1, 4, 5]. At a railway bridge between Reimerzhoven and Dernau (N: 50.532213, E: 7.062320) scouring occurred upstream on the pier in the middle of the riverbed, and bank erosion occurred on the right-hand in flow direction. Riverbed narrowing and sediment deposition at the remaining piers occurred on a small scale. Further upstream, at the town of Altenahr, massive debris accumulation, bridge overtopping, and pier scouring downstream of the middle pier led to structural failure. At this location, a railway bridge and a trafficable bridge were located next to each other (N: 50.514921, E 6.985825). The railway bridge experienced severe bank erosion on the left-hand side in flow direction. After removal, shoal formation led to the cut-off of a stagnant water pool [2]. Processes of pier scouring, bank erosion, and sediment deposition in the following two years differ in both examples. Further investigation and comparison help to gain an understanding of the complex morphologic interaction of bridges in high-energy flood events. Parameters, like the main flow direction and the local flow velocity as well as driftwood accumulation leading to bridge overtopping impact patterns of erosion and deposition. Results can support local water resources management as well as bridge construction authorities.[1] Burghardt L, Schüttrumpf H, Wolf S et al. (2022) Analyse der Schäden an Brückenbauwerken in Folge des Hochwassers 2021 an der Ahr. Wasser Abfall 24:12–17[2] Wolf S, Stark N, Holste I et al. (2023) Evaluation of the High-Energy-Flood of mid-July 2021 as a Morphologic Driver in the Ahr Valley [preprint][3] Lehmkuhl F, Keßels J, Schulte P et al. (2022) Beispiele für morphodynamische Prozesse und Verlagerungen in Folge des Hochflutereignisses 2021 im Ahrtal. Wasser Abfall 24:40–47. https://doi.org/10.1007/s35152-022-1349-7[4] Pucci A, Eickmeier D, Sousa HS et al. (2023) Fragility Analysis Based on Damaged Bridges during the 2021 Flood in Germany. Applied Sciences 13:10454. https://doi.org/10.3390/app131810454[5] Lemnitzer A, Stark N, Gardner M et al. (2022) Geotechnical Reconnaissance of the 2021 Western European Floods. GEER Association (Report - 76)


  • Open Access

    Seismic Retrofit Case Study of Shear-Critical RC Moment Frame T-Beams Strengthened with Full-Wrap FRP Anchored Strips in a High-Rise Building in Los Angeles

    by Susana Anacleto-Lupianez, Luis Herrera, Scott F. Arnold, Winston Chai, Todd Erickson, Anne Lemnitzer

    This paper discusses the iteration of a seismic retrofit solution for shear-deficient end regions of 19 reinforced concrete (RC) moment-resisting frame (MRF) T-beams located in a 12-story RC MRF building in downtown Los Angeles, California. Local strengthening with externally bonded (EB) fiber-reinforced polymer (FRP) fabric was chosen as the preferred retrofit strategy due to its cost-effectiveness and proven performance. The FRP-shear-strengthening scheme for the deficient end-hinging regions of the MRF beams was designed and evaluated through large-scale cyclic testing of three replica specimens. The specimens were constructed at 4/5 scale and cantilever T-beam configurations with lengths of 3.40 m or 3.17 m. The cross-sectional geometry was 0.98 × 0.61 m with a top slab of 1.59 m in width and 0.12 m in thickness. Applied to these specimens were three different retrofit configurations, tested sequentially, namely: (a) unanchored continuous U-wrap; (b) anchored continuous U-wrap with conventional FRP-embedded anchors at the ends; and (c) fully closed external FRP hoops made of discrete FRP U-wrap strips and FRP through-anchors that penetrate the top slab and connect both ends of the FRP strips, combined with intermediate crack-control joints. The strengthening concept with FRP hoops precluded the premature debonding and anchor pullout issues of the two more conventional retrofit solutions and, despite a more challenging and labor-intensive installation, was selected for the in-situ implementation. The proposed hooplike EB-FRP shear-strengthening scheme enabled the deficient MRF beams to overcome a 30% shear overstress at the end-yielding region and to develop high-end rotations (e.g., 0.034 rad [3.4% drift] at peak and 0.038 rad [3.8% drift]) at strength loss for a beam that, otherwise, would have prematurely failed in shear. These values are about 30% larger than the ASCE 41 prescriptive value for the Life Safety (LS) performance objective. Energy dissipation achieved with the fully closed scheme was 108% higher than that of the unanchored FRP U-wrap and 45% higher than that of the FRP U-wrap with traditional embedded anchors. The intermediate saw-cut grooves successfully attracted crack formation between the strips and away from the FRP reinforcement, which contributed to not having any discernable debonding of the strips up to 3% drift. This paper presents the experimental evaluation of the three large-scale laboratory specimens that were used as the design basis for the final retrofit solution.


  • Open Access

    Effects of soil improvement on the axial load capacity of drilled displacement piles – a CPT based case history analysis

    by G. Figueroa Palacios, A. Lemnitzer

    Pile installation is known to affect the surrounding soil, its mechanical properties, and consequently its performance under any type of loading. Data from 11 construction sites, where Cone Penetration Tests (CPT) were performed before (CPTPRE) and after (CPTPOST) pile construction, was used to analyze the change in soil resistance surrounding the Drilled Displacement Piles (DDP). Six of the 11 project sites included static axial load tests, allowing for a comparison between axial pile load predictions using CPTPRE data, load test results during field testing, and analytical capacities obtained through CPTPOST data. This paper will first present a comparison of post-installation soil improvement observed at all 11 sites. The improvement ratio was defined as the CPT tip resistance post-installation (qc.post) divided by the pre-installation resistance (qc.pre). Hereafter, the axial load capacity is analytically estimated using soil resistance parameters before and after the pile construction. Results do not differ considerably when using CPT parameters for stratified soil profiles but showed notable analytical improvement (by a factor of 1.4) for cohesionless soils. However, when comparing analytical estimates using CPT-post data to in-situ failure loads observed from axial load tests, the use of post-installation CPT-based soil parameters for design was deemed premature. While field improvement is evident, its benefit is not correctly reflected in the predicted pile performance, primarily attributed to the uncertainty of capacity predictions for these specialty type of foundations. For cohesive sites, the analytical pile capacity estimated with the CPTPOST and the axial load test data did not show a consistent trend.

  • Settlement Rate Increase in Organic Soils Following Cyclic Loading

    by A. Lemnitzer, S. Yniesta, R. Cappa, S. J. Brandenberg

    Postshaking settlements observed during centrifuge tests of model levees resting atop soft compressible peat are compared with numerical settlement solutions. Two large-scale (9  m ) tests and one small-scale (1  m ) test are analyzed. The models included extensive instrumentation consisting of pore pressure sensors, accelerometers, bender elements, and displacement transducers to measure levee response during and after the application of scaled ground motions at the container base. Postcyclic settlement records suggested an increase in settlement rates within peat on cyclic loading compared with preseismic settlements due to the combined effects of excess pore pressure generation and secondary compression. The observed settlements were compared with the predictions of a one-dimensional nonlinear consolidation code that follows an implicit finite difference formulation. The code includes nonlinear compressibility and permeability properties and models secondary compression strain rate as a function of soil state rather than of time. Secondary compression was found to be the largest contributor to levee settlement. Further, cyclic straining was found to increase the secondary compression rate after earthquake shaking. Incorporating secondary compression reset into settlement predictions resulted in close agreement with measurements, whereas failing to consider secondary compression reset resulted in substantial underprediction of experimental settlement records.


  • Calibration of a New Pressure Sensor and Application to a Dynamic Soil Structure Interaction Study

    by Anne Lemnitzer, Lohrasb Keykhosropour

    Measurement of the distribution and magnitude of static and dynamic earth pressures resulting from geostatic and applied stresses is essential to the design and performance of many civil engineering-type structures involving soil-structure interaction. Seismic soil pressures recorded on a vertical flexible hollow shaft with model scale dimensions of 0.8 m square and 7.0 m in height are compared with predictions from elastic-based analytical approaches found in current literature. The vertical shafts were part of an underground structure system, placed in a laminar soil box, and embedded in a two-layer soil stratigraphy. Two directional ground motions were applied via shake table testing at the E-Defense facility in Japan. Pressure measurements were recorded using recently developed pressure sensors and details pertaining to the design, fabrication, and calibration of the sensor are discussed. Despite of the uncommon geometry of the vertical shaft systems, elastic based methods were able to predict the response reasonably well, in some cases capturing both, pressure magnitudes and pressure distribution.