Joseph Aroh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Joseph Aroh has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Anthony D. Rollett
Carnegie Mellon University
5 shared publications - Benjamin Gould
Applied Materials Division, Argonne National Laboratory, Lemont, USA
5 shared publications - Tao Sun
Department of Materials Science and Engineering, University of Virginia, Charlottesville, USA
4 shared publications - Andrew Chihpin Chuang
X-Ray Science Division, Argonne National Laboratory, Lemont, USA
2 shared publications - Joel V. Bernier
Lawrence Livermore National Laboratory, Livermore, USA
2 shared publications - Rachel E. Lim
Materials Science Division, Lawrence Livermore National Laboratory 1 , Livermore, California 94550
2 shared publications
Latest Publications
- Open Access
- 23 December 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (3) , 808-822
Quantifying Equiaxed vs Epitaxial Solidification in Laser Melting of CMSX-4 Single Crystal Superalloy
The competition between epitaxialvs.equiaxed solidification has been investigated in CMSX-4 single crystal superalloy during laser melting as practiced in additive manufacturing. Single-track laser scans were performed on a powder-free surface of directionally solidified CMSX-4 alloy with several combinations of laser power and scanning velocity. Electron backscattered diffraction (EBSD) mapping facilitated identification of new orientations,i.e., “stray grains” that nucleated within the fusion zone along with their area fraction and spatial distribution. Using high-fidelity computational fluid dynamics simulations, both the temperature and fluid velocity fields within the melt pool were estimated. This information was combined with a nucleation model to determine locations where nucleation has the highest probability to occur in melt pools. In conformance with general experience in metals additive manufacturing, the as-solidified microstructure of the laser-melted tracks is dominated by epitaxial grain growth; nevertheless, stray grains were evident in elongated melt pools. It was found that, though a higher laser scanning velocity and lower power are generally helpful in the reduction of stray grains, the combination of a stable keyhole and minimal fluid velocity further mitigates stray grains in laser single tracks.
- 23 December 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (3) , 808-822
Open AccessQuantifying Equiaxed vs Epitaxial Solidification in Laser Melting of CMSX-4 Single Crystal Superalloy
The competition between epitaxialvs.equiaxed solidification has been investigated in CMSX-4 single crystal superalloy during laser melting as practiced in additive manufacturing. Single-track laser scans were performed on a powder-free surface of directionally solidified CMSX-4 alloy with several combinations of laser power and scanning velocity. Electron backscattered diffraction (EBSD) mapping facilitated identification of new orientations,i.e., “stray grains” that nucleated within the fusion zone along with their area fraction and spatial distribution. Using high-fidelity computational fluid dynamics simulations, both the temperature and fluid velocity fields within the melt pool were estimated. This information was combined with a nucleation model to determine locations where nucleation has the highest probability to occur in melt pools. In conformance with general experience in metals additive manufacturing, the as-solidified microstructure of the laser-melted tracks is dominated by epitaxial grain growth; nevertheless, stray grains were evident in elongated melt pools. It was found that, though a higher laser scanning velocity and lower power are generally helpful in the reduction of stray grains, the combination of a stable keyhole and minimal fluid velocity further mitigates stray grains in laser single tracks.
- 24 November 2021
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 10 (4) , 677-688
Time-Resolved Geometric Feature Tracking Elucidates Laser-Induced Keyhole Dynamics
- 24 November 2021
- Published by Springer Nature in Integrating Materials and Manufacturing Innovation
- Vol. 10 (4) , 677-688
Time-Resolved Geometric Feature Tracking Elucidates Laser-Induced Keyhole Dynamics
- Open Access
- 23 August 2021
- Published by Taylor & Francis in Materials Research Letters
- Vol. 9 (10) , 429-436
High speed synchrotron X-ray diffraction experiments resolve microstructure and phase transformation in laser processed Ti-6Al-4V
The microstructures of Ti-6Al-4V following laser processing depend primarily on the phase transformation of β to α, but their development is constrained by the rapidly changing temperature in the small fusion zone. In-situ synchrotron X-ray diffraction was utilized to probe the rapid phase evolution in single melt tracks with high angular and temporal resolution. Both fully martensitic and mixed α+α′+β microstructures were confirmed by microscopy. Cooling rates were inferred from the lattice parameter history and complementary thermal simulation. It was found that the threshold cooling rate for fully martensitic transformation is in the range between 2900 and 6500°C/s. IMPACT STATEMENT High-speed synchrotron X-ray diffraction during operando laser processing suggests a new threshold between martensitic and diffusional phase transformation in Ti-6Al-4V occurring at higher cooling rates than previously reported.
- 23 August 2021
- Published by Taylor & Francis in Materials Research Letters
- Vol. 9 (10) , 429-436
Open AccessHigh speed synchrotron X-ray diffraction experiments resolve microstructure and phase transformation in laser processed Ti-6Al-4V
The microstructures of Ti-6Al-4V following laser processing depend primarily on the phase transformation of β to α, but their development is constrained by the rapidly changing temperature in the small fusion zone. In-situ synchrotron X-ray diffraction was utilized to probe the rapid phase evolution in single melt tracks with high angular and temporal resolution. Both fully martensitic and mixed α+α′+β microstructures were confirmed by microscopy. Cooling rates were inferred from the lattice parameter history and complementary thermal simulation. It was found that the threshold cooling rate for fully martensitic transformation is in the range between 2900 and 6500°C/s. IMPACT STATEMENT High-speed synchrotron X-ray diffraction during operando laser processing suggests a new threshold between martensitic and diffusional phase transformation in Ti-6Al-4V occurring at higher cooling rates than previously reported.
- Open Access
- 16 July 2021
- Published by ASME International
Morphological Analysis of 316L Laser Powder Bed Fusion Melt-Pool via the Enriched Analytical Solution Method
The recent development of the Enriched Analytical Solution Method (EASM) for evaluating the spatio-temporal distribution of the temperature fields generated during the Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM) processes is providing the opportunity to study the sensitivity of the morphological parameters characterizing the associated melt-pools as a function of
- 16 July 2021
- Published by ASME International
Open AccessMorphological Analysis of 316L Laser Powder Bed Fusion Melt-Pool via the Enriched Analytical Solution Method
The recent development of the Enriched Analytical Solution Method (EASM) for evaluating the spatio-temporal distribution of the temperature fields generated during the Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM) processes is providing the opportunity to study the sensitivity of the morphological parameters characterizing the associated melt-pools as a function of
- 17 November 2020
- Published by Springer Nature in JOM
- Vol. 73 (1) , 212-222
Microscale Observation via High-Speed X-ray Diffraction of Alloy 718 During In Situ Laser Melting
- 17 November 2020
- Published by Springer Nature in JOM
- Vol. 73 (1) , 212-222
Microscale Observation via High-Speed X-ray Diffraction of Alloy 718 During In Situ Laser Melting