Katsuya Tachibana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Katsuya Tachibana has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Tatsuji Yamada
National Metrology Institute of Japan, Tsukuba, Japan
2 shared publications - Toshiaki Shioda
Yokogawa Test and Measurement Corporation, Hachioji, Japan
2 shared publications - Hidekazu Muramatsu
National Metrology Institute of Japan (NMIJ), National Institute of Advanced Industrial Science and Technology (AIST), Ibaraki, Japan
1 shared publication - Norihiko Sakamoto
National Metrology Institute of Japan (NMIJ), National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Japan
1 shared publication
Latest Publications
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-7
A Flexible Evaluation System for the Complex Calibration of Inductive and Resistive Voltage Dividers up to 100 kHz
Toward calibration of wideband resistive voltage dividers (WRVDs), a new evaluation system has been developed, and its validation has been made by employing standard inductive voltage dividers (IVDs) calibrated by Thompson’s method. The evaluation system, designed within 120-V and 100-kHz ranges, introduced a wideband phase standard as a two-phase signal generator, allowing the phase errors of the phase meters in the system to be measured preliminarily. An error correction for the digital lock-in amplifier has also been applied. Those corrections attained a great evaluation performance. Furthermore, the uncertainty of the evaluation system has been estimated by considering some correlations between the uncertainty contributions factors.
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-7
A Flexible Evaluation System for the Complex Calibration of Inductive and Resistive Voltage Dividers up to 100 kHz
Toward calibration of wideband resistive voltage dividers (WRVDs), a new evaluation system has been developed, and its validation has been made by employing standard inductive voltage dividers (IVDs) calibrated by Thompson’s method. The evaluation system, designed within 120-V and 100-kHz ranges, introduced a wideband phase standard as a two-phase signal generator, allowing the phase errors of the phase meters in the system to be measured preliminarily. An error correction for the digital lock-in amplifier has also been applied. Those corrections attained a great evaluation performance. Furthermore, the uncertainty of the evaluation system has been estimated by considering some correlations between the uncertainty contributions factors.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-7
Design Method for a Wideband Resistive Voltage Divider Based on Average Impedance Matching With Optimal Solution Methods
This paper proposes a design method for wideband resistive voltage dividers (WRVDs), working in the range of power frequencies to a few MHz, with serial-parallel construction. It introduces an extended concept of the Hamon method into the WRVDs, not in a conventional way like balancing a bridge, but in a new way that involves impedance matching with optimal solution methods. With this method, average resistance matching and stray capacitance matching are simultaneously realized by an optimal arrangement of two element resistor groups as the input and output resistors. The surrounding stray capacitances between the resistors and chassis are also considered. The performance has been confirmed to improve by about 50 times, compared to that without the method.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-7
Design Method for a Wideband Resistive Voltage Divider Based on Average Impedance Matching With Optimal Solution Methods
This paper proposes a design method for wideband resistive voltage dividers (WRVDs), working in the range of power frequencies to a few MHz, with serial-parallel construction. It introduces an extended concept of the Hamon method into the WRVDs, not in a conventional way like balancing a bridge, but in a new way that involves impedance matching with optimal solution methods. With this method, average resistance matching and stray capacitance matching are simultaneously realized by an optimal arrangement of two element resistor groups as the input and output resistors. The surrounding stray capacitances between the resistors and chassis are also considered. The performance has been confirmed to improve by about 50 times, compared to that without the method.