HPHaesung Park

Haesung Park

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Haesung Park has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Low-Temperature (260 °C) Solderless Cu–Cu Bonding for Fine-Pitch 3-D Packaging and Heterogeneous Integration

    by Haesung Park, Hankyeol Seo, Yoonho Kim, Seungmin Park, Sarah Eunkyung Kim

    Low-temperature solderless Cu-Cu bonding is an important technology for advanced packaging, such as fine-pitch 3-D packaging and heterogeneous integration. In this study, we prepared an oxidation-free Cu surface using an optimized N 2 plasma process in a two-step Ar/N 2 plasma treatment based on the design of the experiment method, to improve direct Cu-Cu bonding quality at 260 °C. The N 2 plasma treatment process was optimized using the Minitab optimizer with chemical state results obtained by X-ray photoelectron spectroscopy (XPS) analysis. The Cu surface treated under the two-step Ar/N 2 plasma with optimized N 2 plasma conditions not only formed Cu nitride well, but the surface remained without further oxidation for at least one week at room temperature. The Cu-Cu bonding was performed at the low bonding temperature of 260 °C and low bonding pressure of 0.9 MPa for 1 hour, and the bonded interface was evaluated using scanning acoustic tomography (SAT) and field emission scanning electron microscope (FE-SEM) images. We measured shear strength to estimate the bonding interface quality of the oxidation-free Cu-Cu bonding specimen. A maximum shear strength of 62.6 MPa was obtained. Our bonding results demonstrated remarkably improved Cu-Cu bonding quality compared with other previous Cu-Cu joint studies that used Sn, Cu/Ag nanoparticles, or Cu composites.


  • Comprehensive Analysis of a Cu Nitride Passivated Surface That Enhances Cu-to-Cu Bonding

    by Hankyeol Seo, Haesung Park, Sarah Eunkyung Kim

    As three-dimensional packaging is expected to meet new requirements for next-generation system-in-packaging (SiP), various technologies have been discussed for vertical integration. To enable high-performance vertical interconnects, Cu-to-Cu bonding is an essential process for decreasing the metal-interconnect size between vertically stacked devices and for improving system performance. However, the high temperature and pressure conditions of the Cu bonding process and copper surface oxidation are important issues to be resolved for better mass production, especially for chip-to-wafer bonding. In this study, comprehensive analysis was performed of the effects of a two-step Ar and N2 plasma treatment used to create a copper nitride passivated surface. Chemical and structural analyses of the copper nitride surface showed that this two-step plasma treatment removed non-uniformly formed native copper oxides and formed an ultra-thin copper nitride passivation layer. Electrical and mechanical analyses showed that the resulting uniform, conductive copper nitride surface and plastic property have the potential to improve the quality of thermocompression bonding. The results of these comprehensive analyses demonstrate the excellent ability of copper nitride to passivate copper surfaces, and indicate the possibility of achieving effective Cu bonding in air.


  • Open Access

    Two-Step Plasma Treatment on Sputtered and Electroplated Cu Surfaces for Cu-To-Cu Bonding Application

    by Hankyeol Seo, Hae Sung Park, Sarah Eunkyung Kim

    The technology trends of next generation electronic packaging are moving toward heterogeneous 3D packaging systems. One of the key processes of 3D packaging system is Cu-to-Cu bonding, which is highly dependent on the planarized, activated, and oxygen-free Cu surface. A two-step plasma treatment is studied to form a Cu surface that does not react with oxygen and improves the Cu bonding interface quality at low bonding temperature (300 °C). In this study, the effects of two-step plasma treatment on both sputtered and electroplated Cu surfaces were evaluated through structural, chemical, and electrical analysis. The Cu bonding interface was studied by scanning acoustic tomography analysis after the thermocompression bonding process. Both sputtered and electroplated Cu thin films had the preferred orientation of (111) plane, but sputtered Cu exhibited larger grains than the electroplated Cu. As a result, the roughness of sputtered Cu was lower, and the resistivity was higher than that of electroplated Cu. Based on X-ray photoelectron spectroscopy analysis, the sputtered Cu formed more copper nitrides and fewer copper oxides than the electroplated Cu. A significant improvement in bonding quality at the Cu bonded interface was observed in sputtered Cu.


  • Open Access

    Opto-Acoustic Method for the Characterization of Thin-Film Adhesion

    by Sanichiro Yoshida, David R. Didie, Daniel Didie, Tomohiro Sasaki, Hae-Sung Park, Ik-Keun Park, David Gurney

    The elastic property of the film-substrate interface of thin-film systems is characterized with an opto-acoustic method. The thin-film specimens are oscillated with an acoustic transducer at audible frequencies, and the resultant harmonic response of the film surface is analyzed with optical interferometry. Polystyrene, Ti, Ti-Au and Ti-Pt films coated on the same silicon substrate are tested. For each film material, a pair of specimens is prepared; one is coated on a silicon substrate after the surface is treated with plasma bombardment, and the other is coated on an identical silicon substrate without a treatment. Experiments indicate that both the surface-treated and untreated specimens of all film materials have resonance in the audible frequency range tested. The elastic constant of the interface corresponding to the observed resonance is found to be orders of magnitude lower than that of the film or substrate material. Observations of these resonance-like behaviors and the associated stiffness of the interface are discussed.