Philippe Olivier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Philippe Olivier has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- C. Paris
Université de Toulouse; Mines Albi; ICA (Institut Clément Ader), Campus Jarlard, Route de Teillet, 81013 Albi Cedex 09, France
2 shared publications - Gérard Bernhart
Université de Toulouse
2 shared publications B. Teissandier
1 shared publication- Bruno Castanié
ISAE-SUPAERO—UPS—IMT Mines Albi—INSA, Institut Clément Ader, Université de Toulouse, F-31400 Toulouse, France
1 shared publication - D. Alvarez1 shared publication
- Edgar Adrian Franco Urquiza
Tecnológico de Monterrey
1 shared publication
Latest Publications
- Open Access
- 2 October 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Influence of Temperature Dependent Properties on Tunneling Cracks in Multi‐Layer Polymer Thin Films
Tunneling cracks severely compromise the mechanical integrity of multi‐layer polymer thin films on stiff substrates. Although previous models assume a constant elastic modulus, this study characterizes four candidate thermoset polymers. Their elastic modulus (), coefficient of thermal expansion (CTE), and glass transition temperature () are modeled as temperature‐dependent properties across both rubbery and glassy states. Due to a significant CTE mismatch with the stiff substrate, cooling below induces severe tensile thermal stresses. A thermo‐mechanical model is developed to analyze these accumulated stresses and calculate the strain energy release rate (G) and crack opening displacement (COD) of tunneling cracks. Results demonstrate that G and COD are significantly influenced by the properties of both the cracked layer and adjacent layers, highlighting critical inter‐layer interactions. A parametric study examines how variations in , and CTE influence G. This research provides a framework for evaluating the mechanical performance of functionalized multi‐layer thin film polymers.
- 2 October 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
Open AccessInfluence of Temperature Dependent Properties on Tunneling Cracks in Multi‐Layer Polymer Thin Films
Tunneling cracks severely compromise the mechanical integrity of multi‐layer polymer thin films on stiff substrates. Although previous models assume a constant elastic modulus, this study characterizes four candidate thermoset polymers. Their elastic modulus (), coefficient of thermal expansion (CTE), and glass transition temperature () are modeled as temperature‐dependent properties across both rubbery and glassy states. Due to a significant CTE mismatch with the stiff substrate, cooling below induces severe tensile thermal stresses. A thermo‐mechanical model is developed to analyze these accumulated stresses and calculate the strain energy release rate (G) and crack opening displacement (COD) of tunneling cracks. Results demonstrate that G and COD are significantly influenced by the properties of both the cracked layer and adjacent layers, highlighting critical inter‐layer interactions. A parametric study examines how variations in , and CTE influence G. This research provides a framework for evaluating the mechanical performance of functionalized multi‐layer thin film polymers.
- Open Access
- 10 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1182, 83-90
Process-Induced Deformations on Composite L-Shaped Part: Numerical Prediction and Compensated Mould Design
This work investigates the formation and control of residual deformations in composite L-shaped parts manufactured by autoclave curing. An experimental study is first conducted to characterize spring-in for different stacking sequences. Dimensional measurements are performed using stereo digital image correlation to quantify spring-in and to assess the presence of warpage along the flanges. A numerical study is then carried out to develop a simulation method for process-induced deformation prediction. The influence of the main mechanisms involved is analyzed, and a modeling strategy for the tool-part interaction is proposed. Finally, compensated mould design is addressed. The convergence of the optimization problem is investigated, and an optimized mold geometry is determined for each part considered in this study.
- 10 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1182, 83-90
Open AccessProcess-Induced Deformations on Composite L-Shaped Part: Numerical Prediction and Compensated Mould Design
This work investigates the formation and control of residual deformations in composite L-shaped parts manufactured by autoclave curing. An experimental study is first conducted to characterize spring-in for different stacking sequences. Dimensional measurements are performed using stereo digital image correlation to quantify spring-in and to assess the presence of warpage along the flanges. A numerical study is then carried out to develop a simulation method for process-induced deformation prediction. The influence of the main mechanisms involved is analyzed, and a modeling strategy for the tool-part interaction is proposed. Finally, compensated mould design is addressed. The convergence of the optimization problem is investigated, and an optimized mold geometry is determined for each part considered in this study.
- Open Access
- 27 May 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 282
Pressure resistance characterisation of vascular networks embedded in carbon composites for high energy physics applications
- 27 May 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 282
Open AccessPressure resistance characterisation of vascular networks embedded in carbon composites for high energy physics applications
- Open Access
- 16 July 2021
- Published by ASME International
Effect of Microstructure Design on Ice Adhesion for Icephobic Application \u2013 an Experimental and Numerical Approach
Ice accretion on aircraft has a negative impact on both safety and performance, as it affects lift, drag, and thrust. As such, there have been great efforts devoted to the development of coatings that reduce ice adhesion, delay ice formation, or shed water droplets before it freezes. Such coatings are referred to as “icephobic coatings”. Among the different surface design
- 16 July 2021
- Published by ASME International
Open AccessEffect of Microstructure Design on Ice Adhesion for Icephobic Application \u2013 an Experimental and Numerical Approach
Ice accretion on aircraft has a negative impact on both safety and performance, as it affects lift, drag, and thrust. As such, there have been great efforts devoted to the development of coatings that reduce ice adhesion, delay ice formation, or shed water droplets before it freezes. Such coatings are referred to as “icephobic coatings”. Among the different surface design
- Open Access
Bearing Strength and Failure Mechanisms of Riveted Woven Carbon Composite Joints
This research aimed to determine riveted carbon/epoxy composites’ mechanical performance when fabricated by resin transfer molding (RTM). As this manufacturing process is gaining importance in the aeronautics and automotive industries, assembly methods and their reliability must be studied in terms of their airworthiness and transportation implementation. The study case resumes the determination of the bearing strength of RTM-woven carbon composites for different rivet joint diameters (1/8, 5/32 and 3/16 in). The joint shear strength was obtained following the ASTM D5961 instructions, and post-failure analysis was carried out by a computerized tomography scan. A residual strength curve is provided with the results to infer the bearing strength for the riveted composites as a function of the rivet width-to-diameter ratio. A discussion of the fracture mechanism and tensile strength is carried out to assess the understanding of the riveted woven composites.
Open AccessBearing Strength and Failure Mechanisms of Riveted Woven Carbon Composite Joints
This research aimed to determine riveted carbon/epoxy composites’ mechanical performance when fabricated by resin transfer molding (RTM). As this manufacturing process is gaining importance in the aeronautics and automotive industries, assembly methods and their reliability must be studied in terms of their airworthiness and transportation implementation. The study case resumes the determination of the bearing strength of RTM-woven carbon composites for different rivet joint diameters (1/8, 5/32 and 3/16 in). The joint shear strength was obtained following the ASTM D5961 instructions, and post-failure analysis was carried out by a computerized tomography scan. A residual strength curve is provided with the results to infer the bearing strength for the riveted composites as a function of the rivet width-to-diameter ratio. A discussion of the fracture mechanism and tensile strength is carried out to assess the understanding of the riveted woven composites.
- Open Access
- 1 October 2020
- Published by Taylor & Francis in International Journal of Smart and Nano Materials
- Vol. 11 (4) , 417-430
Carbon fibres reinforced composites. Electrical impedance analysis: a gateway to smartness
For more than 7 years, our research work is focussed upon the electrical behavior of carbon fiber reinforced composites. Effectively carbon/polymeric matrix laminates can be considered as an electrically conductive network (i.e. carbon fibers) embedded in an insulating medium (i.e. the polymeric matrix). Consequently, from an electrical point of view laminated composites have been modelled owing to combinations of electrical resistances (i.e. fibers themselves and the contact points between the fibers) and capacitances (i.e. polymeric matrix). During their manufacturing, composite material such as thermoset matrix composites for instance, undergo various changes in their physical (including electrical and mechanical) properties and in their geometrical characteristics. In fact, in the case of manufacturing processes such as oven curing (vacuum bag), autoclave curing or heating plate press, beside the chemo-rheological changes, the laminated parts are the place of a compaction phenomenon inducing changes in fiber volume fraction and thicknesses. The idea developed in this paper is that since the carbon/polymeric matrix laminate can be considered as an electrical network, it can then be view and used as a sensor for following the material state during the manufacturing process enabling thus defects to be detected and this without any additional sensing material or device.
- 1 October 2020
- Published by Taylor & Francis in International Journal of Smart and Nano Materials
- Vol. 11 (4) , 417-430
Open AccessCarbon fibres reinforced composites. Electrical impedance analysis: a gateway to smartness
For more than 7 years, our research work is focussed upon the electrical behavior of carbon fiber reinforced composites. Effectively carbon/polymeric matrix laminates can be considered as an electrically conductive network (i.e. carbon fibers) embedded in an insulating medium (i.e. the polymeric matrix). Consequently, from an electrical point of view laminated composites have been modelled owing to combinations of electrical resistances (i.e. fibers themselves and the contact points between the fibers) and capacitances (i.e. polymeric matrix). During their manufacturing, composite material such as thermoset matrix composites for instance, undergo various changes in their physical (including electrical and mechanical) properties and in their geometrical characteristics. In fact, in the case of manufacturing processes such as oven curing (vacuum bag), autoclave curing or heating plate press, beside the chemo-rheological changes, the laminated parts are the place of a compaction phenomenon inducing changes in fiber volume fraction and thicknesses. The idea developed in this paper is that since the carbon/polymeric matrix laminate can be considered as an electrical network, it can then be view and used as a sensor for following the material state during the manufacturing process enabling thus defects to be detected and this without any additional sensing material or device.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1892, 030009
Compaction behavior of out-of-autoclave prepreg materials
The main challenges with composite parts manufacturing are related to the curing means, mainly autoclaves, the length of their cycles and their operating costs. In order to decrease this dependency, out of autoclave materials have been considered as a solution for high production rate parts such as spars, flaps, etc… However, most out-of-autoclave process do not possess the same maturity as their counterpart, especially concerning part quality1. Some pre-cure processes such as compaction and ply lay-up are usually less of a concern for autoclave manufacturing: the pressure applied during the cycle participates to reduce the potential defects (porosity caused by a poor quality lay-up, bad compaction, entrapped air or humidity…). For out-of-autoclave parts, those are crucial steps which may have many consequences on the final quality of the laminate2. In order to avoid this quality loss, those steps must be well understood.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1892, 030009
Compaction behavior of out-of-autoclave prepreg materials
The main challenges with composite parts manufacturing are related to the curing means, mainly autoclaves, the length of their cycles and their operating costs. In order to decrease this dependency, out of autoclave materials have been considered as a solution for high production rate parts such as spars, flaps, etc… However, most out-of-autoclave process do not possess the same maturity as their counterpart, especially concerning part quality1. Some pre-cure processes such as compaction and ply lay-up are usually less of a concern for autoclave manufacturing: the pressure applied during the cycle participates to reduce the potential defects (porosity caused by a poor quality lay-up, bad compaction, entrapped air or humidity…). For out-of-autoclave parts, those are crucial steps which may have many consequences on the final quality of the laminate2. In order to avoid this quality loss, those steps must be well understood.
- 15 August 2012
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 100 (6-7) , 611-622
Influence de cycles de cuisson rapides sur le préimprégné aéronautique M21/T700 : suivi de polymérisation et propriétés mécaniques
Matériaux & Techniques, la revue des matériaux industriels et de leurs techniques de mise en oeuvre
- 15 August 2012
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 100 (6-7) , 611-622
Influence de cycles de cuisson rapides sur le préimprégné aéronautique M21/T700 : suivi de polymérisation et propriétés mécaniques
Matériaux & Techniques, la revue des matériaux industriels et de leurs techniques de mise en oeuvre
- 1 April 2010
- Published by Springer Nature in International Journal of Material Forming
- Vol. 3 (S1) , 639-642
Modelling of the thermokinetic behaviour and the phases transitions of a carbon/polymeric composite submitted to high heating rate ramps
- 1 April 2010
- Published by Springer Nature in International Journal of Material Forming
- Vol. 3 (S1) , 639-642
Modelling of the thermokinetic behaviour and the phases transitions of a carbon/polymeric composite submitted to high heating rate ramps