Aboozar Taherizadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aboozar Taherizadeh has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Pasquale Cavaliere
University of Salento
4 shared publications - Behzad Sadeghi
Department of Innovation Engineering, University of Salento, Lecce, Italy
3 shared publications - Behzad Sadeghian
Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111, Iran
3 shared publications Masoud Atapour
3 shared publications- Abdollah Saboori
Department of Management and Production Engineering, Politecnico di Torino, Torino, Italy
2 shared publications Behzad Sadeghian
2 shared publications
Latest Publications
- Open Access
- 28 September 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (9) , e70560
Creep Simulation of Laser Powder Bed Fused Inconel 718: Performance Evaluation of Material Constitutive Models
Creep deformation limits the high‐temperature use of Inconel 718 components fabricated by laser powder bed fusion (LPBF), affecting safety and maintenance risks. The LPBF process introduces microstructural heterogeneities and anisotropy, making accurate creep prediction challenging. Experimental creep testing can be costly and time‐intensive, highlighting the need for accurate numerical simulations based on effective models. Selecting an appropriate model is crucial, as prior studies have shown the effectiveness of various models in predicting creep behavior. This study aims to evaluate the power law, hyperbolic‐sine, and six‐theta models under different uniaxial stresses (550, 650, 750, and 850 MPa) and temperatures (650°C and 700°C) for LPBF‐fabricated Inconel 718 components using finite element analysis. The results revealed that the power law and hyperbolic sine models showed limited capability in representing the anisotropic and heterogeneous creep response. ANOVA across creep stages confirmed that the six‐theta model reduces prediction error by 20%–30% compared to alternatives, and it demonstrated superior performance in predicting primary creep and subsequent creep rate under all conditions. The six‐theta model outperforming power law and hyperbolic‐sine models. The power law model did not account for the tertiary stage and rupture time, while the hyperbolic‐sine model failed to capture the primary stage.
- 28 September 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (9) , e70560
Open AccessCreep Simulation of Laser Powder Bed Fused Inconel 718: Performance Evaluation of Material Constitutive Models
Creep deformation limits the high‐temperature use of Inconel 718 components fabricated by laser powder bed fusion (LPBF), affecting safety and maintenance risks. The LPBF process introduces microstructural heterogeneities and anisotropy, making accurate creep prediction challenging. Experimental creep testing can be costly and time‐intensive, highlighting the need for accurate numerical simulations based on effective models. Selecting an appropriate model is crucial, as prior studies have shown the effectiveness of various models in predicting creep behavior. This study aims to evaluate the power law, hyperbolic‐sine, and six‐theta models under different uniaxial stresses (550, 650, 750, and 850 MPa) and temperatures (650°C and 700°C) for LPBF‐fabricated Inconel 718 components using finite element analysis. The results revealed that the power law and hyperbolic sine models showed limited capability in representing the anisotropic and heterogeneous creep response. ANOVA across creep stages confirmed that the six‐theta model reduces prediction error by 20%–30% compared to alternatives, and it demonstrated superior performance in predicting primary creep and subsequent creep rate under all conditions. The six‐theta model outperforming power law and hyperbolic‐sine models. The power law model did not account for the tertiary stage and rupture time, while the hyperbolic‐sine model failed to capture the primary stage.
- Open Access
- 8 April 2024
- Published by Elsevier in Materialia
- Vol. 34
Architecting strength: Innovative microstructural design of Aluminum/Alumina Nanocomposites via cold-welded flaky-shaped particles and pressure-assisted sintering
- 8 April 2024
- Published by Elsevier in Materialia
- Vol. 34
Open AccessArchitecting strength: Innovative microstructural design of Aluminum/Alumina Nanocomposites via cold-welded flaky-shaped particles and pressure-assisted sintering
- Open Access
- 1 March 2024
- Published by Academic World Research in Journal of Computational Methods In Engineering
- Vol. 42 (2) , 129-147
Thermomechanical and microstructural simulation of rotary friction welding process of Inconel718 alloy using the finite element method
Rotary friction welding is one of the most important techniques for joining different parts in advanced industries. Measuring the history of thermomechanical and microstructural parameters can be challenging and costly. To address these challenges, the finite element method was used to simulate thermomechanical and microstructural aspects of the welding of identical superalloy Inconel718 tubes. Therefore, in this research, thermomechanical and microstructural simulations were developed to calculate essential mechanical and metallurgical parameters such as temperature, strain, strain rate, volume fraction of dynamic recrystallization, and grain size distribution. Some of these parameters were then used to be verified with experimental test results. In the microstructural simulation, the Johnson-Avrami model was applied to convert thermomechanical parameters to metallurgical factors by using a FORTRAN subroutine. By employing the dynamic recrystallization kinetics model, the thickness of the recrystallization zone in the wall thickness was calculated to be 480 and 850 micrometers at the center and edge of the tube wall, respectively. These values were reported in the experimental measurements as 500 and 800 micrometers, respectively. Additionally, the grain size change from the center to the edge of the wall thickness, close to the weld interface, were predicted from 2.07 to 2.15 micrometers by simulations, which was comparable with the experimental measurements of 1.9 to 2.2 micrometers. Also, different types of curves were represented to investigate the correlation between thermomechanical and microstructural parameters. Predictable results were concluded from microstructure evolutions with changes by thermomechanical results.
- 1 March 2024
- Published by Academic World Research in Journal of Computational Methods In Engineering
- Vol. 42 (2) , 129-147
Open AccessThermomechanical and microstructural simulation of rotary friction welding process of Inconel718 alloy using the finite element method
Rotary friction welding is one of the most important techniques for joining different parts in advanced industries. Measuring the history of thermomechanical and microstructural parameters can be challenging and costly. To address these challenges, the finite element method was used to simulate thermomechanical and microstructural aspects of the welding of identical superalloy Inconel718 tubes. Therefore, in this research, thermomechanical and microstructural simulations were developed to calculate essential mechanical and metallurgical parameters such as temperature, strain, strain rate, volume fraction of dynamic recrystallization, and grain size distribution. Some of these parameters were then used to be verified with experimental test results. In the microstructural simulation, the Johnson-Avrami model was applied to convert thermomechanical parameters to metallurgical factors by using a FORTRAN subroutine. By employing the dynamic recrystallization kinetics model, the thickness of the recrystallization zone in the wall thickness was calculated to be 480 and 850 micrometers at the center and edge of the tube wall, respectively. These values were reported in the experimental measurements as 500 and 800 micrometers, respectively. Additionally, the grain size change from the center to the edge of the wall thickness, close to the weld interface, were predicted from 2.07 to 2.15 micrometers by simulations, which was comparable with the experimental measurements of 1.9 to 2.2 micrometers. Also, different types of curves were represented to investigate the correlation between thermomechanical and microstructural parameters. Predictable results were concluded from microstructure evolutions with changes by thermomechanical results.
- Open Access
Thermal–Mechanical and Microstructural Simulation of Rotary Friction Welding Processes by Using Finite Element Method
Rotary friction welding is one of the most crucial techniques for joining different parts in advanced industries. Experimentally measuring the history of thermomechanical and microstructural parameters of this process can be a significant challenge and incurs high costs. To address these challenges, the finite element method was used to simulate thermomechanical and microstructural aspects of the welding of identical superalloy Inconel 718 tubes. Numerical simulation results were used to compute essential mechanical and metallurgical parameters such as temperature, strain, strain rate, volume fraction of dynamic recrystallization, and grain size distribution. These parameters were subsequently verified using experimental test results. The Johnson–Avrami model was utilized in the microstructural simulation to convert thermomechanical parameters into metallurgical factors, employing a FORTRAN subroutine. The calculated thickness of the recrystallization zone in the wall was 480 and 850 μm at the tube wall’s center and edge, respectively. These values were reported from experimental measurements as 500 and 800 μm, respectively. The predicted grain size changes from the center to the edge of the wall thickness, near the weld interface, ranged from 2.07 to 2.15 μm, comparable to the experimental measurements ranging from 1.9 to 2.2 μm. Various curves are also presented to explore the correlation between thermomechanical and microstructural parameters, with the experimental results revealing predictable microstructure evolutions correlated with thermomechanical changes.
Open AccessThermal–Mechanical and Microstructural Simulation of Rotary Friction Welding Processes by Using Finite Element Method
Rotary friction welding is one of the most crucial techniques for joining different parts in advanced industries. Experimentally measuring the history of thermomechanical and microstructural parameters of this process can be a significant challenge and incurs high costs. To address these challenges, the finite element method was used to simulate thermomechanical and microstructural aspects of the welding of identical superalloy Inconel 718 tubes. Numerical simulation results were used to compute essential mechanical and metallurgical parameters such as temperature, strain, strain rate, volume fraction of dynamic recrystallization, and grain size distribution. These parameters were subsequently verified using experimental test results. The Johnson–Avrami model was utilized in the microstructural simulation to convert thermomechanical parameters into metallurgical factors, employing a FORTRAN subroutine. The calculated thickness of the recrystallization zone in the wall was 480 and 850 μm at the tube wall’s center and edge, respectively. These values were reported from experimental measurements as 500 and 800 μm, respectively. The predicted grain size changes from the center to the edge of the wall thickness, near the weld interface, ranged from 2.07 to 2.15 μm, comparable to the experimental measurements ranging from 1.9 to 2.2 μm. Various curves are also presented to explore the correlation between thermomechanical and microstructural parameters, with the experimental results revealing predictable microstructure evolutions correlated with thermomechanical changes.
- Open Access
- 6 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 3294-3311
Microstructure-electrochemical behavior relationship in post processed AISI316L stainless steel parts fabricated by laser powder bed fusion
- 6 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 3294-3311
Open AccessMicrostructure-electrochemical behavior relationship in post processed AISI316L stainless steel parts fabricated by laser powder bed fusion
- Open Access
Simulation and Microstructure Prediction of Resistance Spot Welding of Stainless Steel to Carbon Steel
Joining of stainless steel to carbon steel is widely used in various industries. Resistance spot welding (RSW) is a suitable process for joining steel sheets. Due to the complexity and importance of optimizing the parameters, numerical simulation of this process was considered. In this research, the electrical-thermal-mechanical simulation of RSW of 304 stainless steel to St37 carbon steel was performed using finite element method (FEM). Then, the simulated weld nugget size was compared with the experimental results of optical microscopy (OM). In addition, diffusion of metallic elements of the steels in the molten region was simulated using Fick’s equation and compared with experimental results of energy-dispersive X-ray spectroscopy (EDS). It was shown that diffusion of Cr and Ni through the weld nugget, would make a new stainless steel structure. Microstructure prediction of the heat affected zone (HAZ) was performed using Koistinen–Marburger and Leblond–Devaux equations to predict the percentage of martensite and ferrite-perlite phases during the heating and cooling stages of the specimens from room temperature to the peak temperature and cooling down under the Mf temperature. The results of this simulation were validated by scanning electron microscopy (SEM) images and shear tensile and micro-hardness test results. The simulation results showed that increasing the heat input from 1250 A during 0.5 s to 3750 A during 1.5 s, increases the percentage of martensite, from 40% to 80%, in the HAZ and widens the martensite region.
Open AccessSimulation and Microstructure Prediction of Resistance Spot Welding of Stainless Steel to Carbon Steel
Joining of stainless steel to carbon steel is widely used in various industries. Resistance spot welding (RSW) is a suitable process for joining steel sheets. Due to the complexity and importance of optimizing the parameters, numerical simulation of this process was considered. In this research, the electrical-thermal-mechanical simulation of RSW of 304 stainless steel to St37 carbon steel was performed using finite element method (FEM). Then, the simulated weld nugget size was compared with the experimental results of optical microscopy (OM). In addition, diffusion of metallic elements of the steels in the molten region was simulated using Fick’s equation and compared with experimental results of energy-dispersive X-ray spectroscopy (EDS). It was shown that diffusion of Cr and Ni through the weld nugget, would make a new stainless steel structure. Microstructure prediction of the heat affected zone (HAZ) was performed using Koistinen–Marburger and Leblond–Devaux equations to predict the percentage of martensite and ferrite-perlite phases during the heating and cooling stages of the specimens from room temperature to the peak temperature and cooling down under the Mf temperature. The results of this simulation were validated by scanning electron microscopy (SEM) images and shear tensile and micro-hardness test results. The simulation results showed that increasing the heat input from 1250 A during 0.5 s to 3750 A during 1.5 s, increases the percentage of martensite, from 40% to 80%, in the HAZ and widens the martensite region.
- Open Access
- 1 November 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (11) , 3217-3233
Quasi-in vivo corrosion behavior of AZ31B Mg alloy with hybrid MWCNTs-PEO/PCL based coatings
- 1 November 2022
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 10 (11) , 3217-3233
Open AccessQuasi-in vivo corrosion behavior of AZ31B Mg alloy with hybrid MWCNTs-PEO/PCL based coatings