Ngoc Minh Le
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ngoc Minh Le has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Anke Dalke
Tech Univ Bergakademie Freiberg, Inst Mat Engn, Gustav Zeuner Str 5, D-09599 Freiberg, Germany
3 shared publications - Horst Biermann
TU Bergakademie Freiberg
3 shared publications - Christian Schimpf
Institute of Materials Science TU Bergakademie Freiberg Freiberg Germany
2 shared publications - Andreas Leineweber
Institute of Materials Science , TU Bergakademie Freiberg , Gustav-Zeuner-Str. 5, 09599 Freiberg , Germany
1 shared publication Anke Dalke
1 shared publicationHorst Biermann
1 shared publication
Latest Publications
- Open Access
- 26 March 2026
- Published by Elsevier in SSRN Electronic Journal
Diffusion Phenomena and Phase and Microstructure Formation During Nitriding of Fe-40at.%Al
Nitriding of FeAl40 (Fe–40 at.%Al) intermetallic high-temperature alloy allows improving its anti-wear properties. Such nitriding leads to the formation of an outer white layer composed of iron nitrides and an inner diffusion zone with precipitated AlN. In the present work, gaseous nitriding was performed at 590 °C over a wide range of nitriding potentials and treatment times. The specimens have been investigated by scanning electron microscopy supplemented by electron backscatter diffraction, electron probe microanalysis, transmission electron microscopy and X-ray diffraction. These measurements reveal the microstructure evolution and form the basis for explaining the observed layer growth kinetics on the basis of an internal nitriding mechanism governed by inwards diffusion of N and immediate precipitation of lamellar AlN. The compressive stress induced by the nitriding leads to previously reported out-diffusion of preferably Fe developing the white layer, but also to the formation of Fe-rich wave-like features developing by Fe diffusion to grain boundaries oriented parallel to the surface. It is argued that the high interface density obviously facilitates these diffusive processes, since Fe volume diffusion is not sufficiently rapid to account for the observed diffusion lengths. With increasing nitriding potentials also appreciable regions of the diffusion layer transform to iron nitrides. Notably, the ε-iron nitrides develop in the lamellar AlN-containing regions, whereas the Fe-rich wave-like features transform to γ′-iron nitrides. It is likely the presence of Al and/or microstructural constraints that prevent the formation of the γ′-iron nitrides in the case of the lamellar AlN-containing regions.
- 26 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDiffusion Phenomena and Phase and Microstructure Formation During Nitriding of Fe-40at.%Al
Nitriding of FeAl40 (Fe–40 at.%Al) intermetallic high-temperature alloy allows improving its anti-wear properties. Such nitriding leads to the formation of an outer white layer composed of iron nitrides and an inner diffusion zone with precipitated AlN. In the present work, gaseous nitriding was performed at 590 °C over a wide range of nitriding potentials and treatment times. The specimens have been investigated by scanning electron microscopy supplemented by electron backscatter diffraction, electron probe microanalysis, transmission electron microscopy and X-ray diffraction. These measurements reveal the microstructure evolution and form the basis for explaining the observed layer growth kinetics on the basis of an internal nitriding mechanism governed by inwards diffusion of N and immediate precipitation of lamellar AlN. The compressive stress induced by the nitriding leads to previously reported out-diffusion of preferably Fe developing the white layer, but also to the formation of Fe-rich wave-like features developing by Fe diffusion to grain boundaries oriented parallel to the surface. It is argued that the high interface density obviously facilitates these diffusive processes, since Fe volume diffusion is not sufficiently rapid to account for the observed diffusion lengths. With increasing nitriding potentials also appreciable regions of the diffusion layer transform to iron nitrides. Notably, the ε-iron nitrides develop in the lamellar AlN-containing regions, whereas the Fe-rich wave-like features transform to γ′-iron nitrides. It is likely the presence of Al and/or microstructural constraints that prevent the formation of the γ′-iron nitrides in the case of the lamellar AlN-containing regions.
- Open Access
Effect of N2–H2 Ratio during Conventional Plasma Nitriding of Intermetallic FeAl40 Alloy on Electrochemical Corrosion Parameters in Sulphuric Acid
The intermetallic alloy FeAl40 was plasma nitrided at 575 C for 4 h while varying the N–H gas mixture with nitrogen contents f between 0.1 and 0.9. The effect of the gas mixture on the resulting structure of the nitrided FeAl40 and the associated electrochemical corrosion behaviour in a 0.25 M HSO (pH = 0.3) electrolyte were investigated using different complementary analytical methods such as scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray spectroscopy, electron probe microanalysis (EPMA), electrochemical polarisation and electrochemical impedance spectroscopy. Nitriding significantly changed the corrosion mechanism of FeAl40 alloys in acidic environments, ranging from consistently high material loss in untreated base material to strongly inhibited material loss. This phenomenon was the result of a corrosion product layer formed on nitrided FeAl40 during the corrosion process. Therefore, plasma nitriding reduced the corrosion rate to about 5–7 mm/year compared with 22 mm/year of the untreated FeAl40 base material. A high nitrogen content in the N–H plasma of more than f = 0.3 ensured the formation of protective nitrided layers on FeAl40. In addition, an approach to explaining the effect of the nitrided layer on FeAl materials was presented on the basis of thermodynamic considerations.Open AccessEffect of N2–H2 Ratio during Conventional Plasma Nitriding of Intermetallic FeAl40 Alloy on Electrochemical Corrosion Parameters in Sulphuric Acid
The intermetallic alloy FeAl40 was plasma nitrided at 575 C for 4 h while varying the N–H gas mixture with nitrogen contents f between 0.1 and 0.9. The effect of the gas mixture on the resulting structure of the nitrided FeAl40 and the associated electrochemical corrosion behaviour in a 0.25 M HSO (pH = 0.3) electrolyte were investigated using different complementary analytical methods such as scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray spectroscopy, electron probe microanalysis (EPMA), electrochemical polarisation and electrochemical impedance spectroscopy. Nitriding significantly changed the corrosion mechanism of FeAl40 alloys in acidic environments, ranging from consistently high material loss in untreated base material to strongly inhibited material loss. This phenomenon was the result of a corrosion product layer formed on nitrided FeAl40 during the corrosion process. Therefore, plasma nitriding reduced the corrosion rate to about 5–7 mm/year compared with 22 mm/year of the untreated FeAl40 base material. A high nitrogen content in the N–H plasma of more than f = 0.3 ensured the formation of protective nitrided layers on FeAl40. In addition, an approach to explaining the effect of the nitrided layer on FeAl materials was presented on the basis of thermodynamic considerations. - Open Access
- 1 December 2020
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 52 (1) , 414-424
Effect of Nitriding Potential KN on the Formation and Growth of a “White Layer” on Iron Aluminide Alloy
This paper investigates the effect of nitriding potential under well-defined gas nitriding conditions on the formation and growth of a compound layer called “white layer” on a FeAl40 (with the composition of 40 at. pct Al) iron aluminide alloy. The nitriding potential was systematically varied in the range of 0.1 to 1.75 bar−1/2 at 590 °C for 5 hour nitriding time with an ammonia-hydrogen-nitrogen atmosphere. Characterization of the microstructure and phases formed within the white layer was performed using optical and scanning electron microscopy, X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and glow discharge optical emission spectroscopy (GDOES). Experimental results indicated that the nitriding potential strongly influences morphology and crystal structure of the white layer. The nitride compound layer consists of the phases γ′-Fe4N, ε-Fe2-3N, and AlN. A mechanism is proposed for the formation and growth of the white layer, depending on the effect of the nitriding potential.
- 1 December 2020
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 52 (1) , 414-424
Open AccessEffect of Nitriding Potential KN on the Formation and Growth of a “White Layer” on Iron Aluminide Alloy
This paper investigates the effect of nitriding potential under well-defined gas nitriding conditions on the formation and growth of a compound layer called “white layer” on a FeAl40 (with the composition of 40 at. pct Al) iron aluminide alloy. The nitriding potential was systematically varied in the range of 0.1 to 1.75 bar−1/2 at 590 °C for 5 hour nitriding time with an ammonia-hydrogen-nitrogen atmosphere. Characterization of the microstructure and phases formed within the white layer was performed using optical and scanning electron microscopy, X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and glow discharge optical emission spectroscopy (GDOES). Experimental results indicated that the nitriding potential strongly influences morphology and crystal structure of the white layer. The nitride compound layer consists of the phases γ′-Fe4N, ε-Fe2-3N, and AlN. A mechanism is proposed for the formation and growth of the white layer, depending on the effect of the nitriding potential.