Ben La Riviere
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ben La Riviere has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Padhraic Mulligan
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
2 shared publications Adrian Schrell
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication- Anne A. Campbell
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication Bruce Warmack
ORNL
1 shared publication- Chad M. Parish
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication - David Glasgow
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
1 shared publication
Latest Publications
- Open Access
- 1 March 2024
- Published by Office of Scientific and Technical Information (OSTI)
Modeling and Design of Micro Flux Monitors for Neutron Fluence Measurements
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 March 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessModeling and Design of Micro Flux Monitors for Neutron Fluence Measurements
The U.S. Department of Energy's Office of Scientific and Technical Information
- Open Access
- 1 August 2023
- Published by Office of Scientific and Technical Information (OSTI)
Qualification of Commercially Available Silicon Carbide for Passive Thermometry in Reactor Experiments – FY23 Status Report
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 August 2023
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessQualification of Commercially Available Silicon Carbide for Passive Thermometry in Reactor Experiments – FY23 Status Report
The U.S. Department of Energy's Office of Scientific and Technical Information
- 11 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 22 (4) , 493-499
Irradiation-Induced Degradation of Surface Acoustic Wave Devices Fabricated on Bulk AlN
Here, recent work to evaluate the prospects for surface acoustic wave (SAW) devices fabricated on bulk aluminum nitride (AlN) for elevated temperature and radiation environments is reported and discussed. The design and fabrication of an array of SAW devices using commercial wafers is described, including the non-standard fabrication approach taken to overcome the stress-induced warpage of the 50 mm diameter AlN substrates. Radio frequency performance characterization of the SAW devices, with resonance frequencies ranging from 0.5 GHz to 1.5 GHz, is described. The linear temperature coefficient of frequency (TCF) near room temperature was measured and is compared to theoretical results from other investigators. The effects of 8 MeV Al ion irradiation at 300∘C and 500∘C to damage levels of 0.01, 0.1 and 1 displacements per atom (dpa), as a proxy for neutron irradiation, was investigated. The ion irradiation damage was observed to decrease the SAW resonant frequency, and this effect is characterized and discussed. Significant degradation in the conductivity of the Ti/Al electrodes of the SAW devices was also observed and characterized. These experimental results provide a basis for further investigation of the prospects for development of SAW sensor devices in bulk AlN material for application in elevated temperature and radiation environments.
- 11 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 22 (4) , 493-499
Irradiation-Induced Degradation of Surface Acoustic Wave Devices Fabricated on Bulk AlN
Here, recent work to evaluate the prospects for surface acoustic wave (SAW) devices fabricated on bulk aluminum nitride (AlN) for elevated temperature and radiation environments is reported and discussed. The design and fabrication of an array of SAW devices using commercial wafers is described, including the non-standard fabrication approach taken to overcome the stress-induced warpage of the 50 mm diameter AlN substrates. Radio frequency performance characterization of the SAW devices, with resonance frequencies ranging from 0.5 GHz to 1.5 GHz, is described. The linear temperature coefficient of frequency (TCF) near room temperature was measured and is compared to theoretical results from other investigators. The effects of 8 MeV Al ion irradiation at 300∘C and 500∘C to damage levels of 0.01, 0.1 and 1 displacements per atom (dpa), as a proxy for neutron irradiation, was investigated. The ion irradiation damage was observed to decrease the SAW resonant frequency, and this effect is characterized and discussed. Significant degradation in the conductivity of the Ti/Al electrodes of the SAW devices was also observed and characterized. These experimental results provide a basis for further investigation of the prospects for development of SAW sensor devices in bulk AlN material for application in elevated temperature and radiation environments.
- Open Access
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 211085-211090
Surface Acoustic Wave Devices Printed at the Aerosol-Jet Resolution Limit
Leveraging advances in additive manufacturing to implement radio frequency sensor technology has gained interest in recent years, motivated in part by the prospect of cost-effective, multi parameter sensing. Herein, aerosol-jet (AJ) printed surface acoustic wave (SAW) devices on LiNbO3 with features at the resolution limit of AJ printing are reported. Compared to previously reported work, these devices demonstrate improved agreement between SAW designed and measured operating frequency at finer printed feature size, increased operating fundamental frequency, and are the first reported exploitation of harmonics of printed SAW sensor devices. Additionally, the application of printed SAWs as electrical resistance sensors and temperature sensors is demonstrated.
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 211085-211090
Open AccessSurface Acoustic Wave Devices Printed at the Aerosol-Jet Resolution Limit
Leveraging advances in additive manufacturing to implement radio frequency sensor technology has gained interest in recent years, motivated in part by the prospect of cost-effective, multi parameter sensing. Herein, aerosol-jet (AJ) printed surface acoustic wave (SAW) devices on LiNbO3 with features at the resolution limit of AJ printing are reported. Compared to previously reported work, these devices demonstrate improved agreement between SAW designed and measured operating frequency at finer printed feature size, increased operating fundamental frequency, and are the first reported exploitation of harmonics of printed SAW sensor devices. Additionally, the application of printed SAWs as electrical resistance sensors and temperature sensors is demonstrated.