VDViktoriia Dmytrenko

Viktoriia Dmytrenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Viktoriia Dmytrenko has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development of a mathematical model for gas hydrate synthesis and dissociation processes in a gas pipeline under microwave radiation

    by Taras Podoliak, Victoriia Dmytrenko

    The object of research is the heat and mass transfer processes that occur on the surface of a gas hydrate granule moving in a gas pipeline. The research solved the problem of the oil and gas industry – the fight against the formation of gas hydrates (GH) in hydrocarbon production and transportation systems. A promising approach to the intensification of hydrate dissociation by using microwave electromagnetic radiation is proposed. The features of the results obtained consist in the development of a mathematical model that combines two processes of synthesis and dissociation of gas hydrates, taking into account hydrodynamic processes in the pipeline. The main differences of the proposed mathematical model are: simultaneous consideration of two mutually opposing processes of synthesis and dissociation of gas hydrate on the surface of the granule; these processes occur during the movement of the gas hydrate granule inside the gas pipeline; heating of the gas hydrate granule occurs as a result of its absorption of direct and reflected multimode microwave electromagnetic radiation. A complex approximation dependence was obtained for determining the required emitter power Pw = 124Cgh/R1.7, which allows one to quickly calculate the required minimum magnetron power to combat hydrate formation. It was established that for the destruction of small particles (0.1%) with particle sizes of 0.05–0.1 mm. Therefore, the most advantageous strategy for combating GH accumulation is its active destruction when it reaches sizes of 0.02–0.05 mm, which do not harm the course of the main technological process. The obtained dependences are the basis for improving gas preparation technologies under hydrate formation conditions by using microwave radiation energy.

  • Open Access

    Application of ultra-high frequency electromagnetic radiation energy to increase the efficiency of gas preparation processes in hydrate formation conditions

    by Taras Podoliak, Victoriia Dmytrenko

    The effective operation of modern gas systems requires new approaches to combat hydrate plugs, which limit the flow and cause emergency shutdowns. The object of research is the process of formation and destruction of gas hydrates in industrial pipelines under the influence of microwave radiation. The research is aimed at solving the problem of excessive use of methanol to combat hydrates. This reagent is very toxic and expensive, and its real costs in the fields of Ukraine are often 15–20% higher than the norm due to outdated dosing methods. The results of the work are based on modeling the technological processes of the Machukhske field (Ukraine) in the Aspen HYSYS program. The most dangerous zone of hydrate formation was identified in a 20-meter section immediately after the throttle when the gas temperature drops to –30.11°C. To protect this unit, a new design of a removable insert with a magnetron has been developed, which provides thermodynamic decomposition of crystal hydrates by directly transferring the energy of the microwave field to water molecules in the flow volume. A distinctive feature of the development is the creation of a resonant zone between the choke and the diaphragm, which allows concentrating the field and accelerating the dissociation of hydrates by 1.5–3 times compared to thermal heating. The optimized geometry of the diaphragm provides high wave reflection without a significant increase in the hydrodynamic resistance of the gas flow. The practical value of the work lies in the possibility of integrating the developed design of the ultrahigh-frequency electromagnetic radiation device into low-temperature gas separation units and hydrocarbon collection systems with a complex temperature regime. The introduction of the device allows maintaining a stable hydrate-free mode of pipeline operation, reducing the consumption of chemical reagents and increasing the environmental safety of gas production in Ukrainian fields by minimizing the use of toxic methanol.

  • Open Access

    MODELING OF MACROGALVANIC CORROSION OF OIL PIPELINES TAKING INTO ACCOUNT VARIABLE PHYSICAL AND CHEMICAL PROPERTIES OF THE SOIL

    by Viktoriia Dmytrenko, Yevhen Stepovyi

    The article comprehensively examines the problem of ensuring the reliability of main oil pipelines in conditions of a changing soil environment, which significantly affects the intensity of corrosion processes. Particular attention is paid to the influence of soil moisture and ohmic resistance, which determine the electrochemical conditions for the formation of macrogalvanic couples – a key factor accelerating localized corrosion of pipeline metal. The aim of the study is to create a mathematical model capable of accurately describing the distribution of electrochemical potentials and corrosion currents along the pipeline system, taking into account both the properties of the metal and the variable parameters of the external environment. The proposed numerical model is based on solving a system of nonlinear algebraic equations using iterative methods, which allows for detailed simulation of the effect of variable soil moisture on the electrochemical behavior of metal surfaces. The article also provides an analytical description of changes in the parameters of a macrogalvanic couple depending on the level of moisture and electrical resistance of the soil, and proposes a method for calculating the specific polarizability of pipeline metal in different sections of the pipeline. The proposed model allows not only to accurately assess the remaining resource of pipeline systems, but also to identify accident-prone areas in a timely manner, thereby increasing the efficiency of cathodic protection systems. The results obtained are of practical value for the creation of specialized engineering software and can be used in the development of the latest regulatory and technical documents in the field of monitoring and protection of underground pipeline systems. Keywords: steel oil pipeline, electrochemical corrosion, longitudinal galvanocouple, corrosion model, corrosion rate, environmental safety.

  • RESEARCH ON ENVIRONMENTALLY SAFE LUBRICANT ADDITIVES TO DRILLING FLUIDS

    by Viktoriia Dmytrenko, Ivan Zezekalo, Anatolii Krol

    The use of lubricating additives (lubricants) in drilling and processing fluids is key to the successful construction of oil and gas wells. They play a decisive role in improving the technical, technological, economic and environmental performance of the entire process. In recent years, environmentally friendly lubricating additives have become particularly relevant in the sector of drilling fluids for deep oil and gas wells. The paper presents the results of experimental studies of the anti-fraction properties of environmentally safe compositions of lubricating additives. A new environmentally safe lubricating additive for flushing fluids with improved tribological characteristics has been developed, which ensures trouble-free drilling of the oil and gas wellbore, including during the exposure of rocks containing drinking and potentially drinking groundwater horizons. According to the results of laboratory experiments, the best indicators in terms of lubricity, heat resistance and salt resistance are found in compositions based on alkylamine salts of a mixture of fatty acids of vegetable oils and tall oil. It was found that the composition "Burol-2" most effectively affects the tribological characteristics of the flushing fluid. The friction coefficients of CTC and KMTP are significantly reduced at a concentration of the lubricating additive of 0.5% vol., while the adhesive properties reach regulated values (Kpr < 30). The optimal additive to model flushing fluids of this type can be considered to be 1.0% vol. The developed composition consists of environmentally safe components based on alkylamine salts of a mixture of selected fatty acids of vegetable oils and tall oil with additives of chemical reagents that improve emulsification, anti-depressant effect, and anti-depressant low-temperature characteristics. The results of the research show that the lubricating properties of model flushing fluids have better indicators when treated with 1.0% vol. of the developed composition "Burol-2" compared to other lubricating additives used by domestic drilling enterprises.

  • Open Access

    Research of methanol content in technological flows of facilities that process gas preparation by low-temperature separation method

    by Viktoriia Dmytrenko, Taras Podoliak

    The object of research is methanol as an inhibitor, which is used in the process of collecting and preparing products from gas, gas condensate, and oil fields to protect against hydrate formations. It is important to ensure the rational consumption of this inhibitor, taking into account its solubility in gas, water, and liquid hydrocarbons. This work is aimed at analyzing the use of the methanol hydrate formation inhibitor in the process of low-temperature gas preparation and determining ways to use it more effectively. The work presents the results of modeling the distribution of the hydrate formation inhibitor along the technological flows of low-temperature gas separation units according to the following schemes: – low-temperature separation with gas cooling due to the Joule-Thompson effect; – compression of gas from wells using PCS (pressure compressor station) + low-temperature separation with gas cooling due to the Joule-Thompson effect; – compression of gas from wells using PCS + low-temperature separation with gas cooling due to the operation of a turboexpander unit; – compression of gas from wells using PCS + low-temperature separation with gas cooling due to the operation of an artificial refrigeration unit (propane refrigeration unit). The use of a computer simulator allowed to track in detail the distribution of methanol during the gas preparation process. The iteration method determined the minimum values of methanol consumption at which the hydrate-free operation mode of the equipment is maintained. Based on the modeling results, an analysis of methanol content in technological flows was performed. And the patterns of inhibitor separation in the separation equipment were also determined, namely, the dependence of methanol distribution on gas pressure in separators, and the methanol content in the output lines of gas preparation units. It was established that the results of the study can be applied in the development of technologies for the collection, regeneration and reuse of methanol in technological processes of low-temperature gas preparation. The practical value of the results lies in the possibility of improving typical methods of protecting equipment from hydrate formations by developing an automated inhibitor supply system that, by monitoring the parameters of the technological process, changes the inhibitor dosage and ensures its economical use.


  • INCREASE OF THE LUBRICATING PROPERTIES OF WATER-CLAY DRILLING MUDS DURING INCLINED AND HORIZONTAL DRILLING

    by Viktoriia Dmytrenko, Yuliia Diachenko

    The paper presents the results of experimental studies of the antifracturing properties of natural oils: castor, hemp, rapeseed, soybean, mustard, sunflower, and corn. The results of the experiments are presented, which allow to evaluate the effect of the studied natural oils on the parameters of fresh, mineralized and saline-saturated water-clay drilling mud (density, rheological and structural-mechanical properties, pH level, filtration index, thickness and stickiness of the clay crust, lubrication coefficient). The experiment was conducted using the methodology of the American Petroleum Institute (according to API standards). It was established that in the fresh solution, rapeseed oil in concentrations of 1 and 3 % and sunflower oil in a concentration of 1 % showed the most effective lubricating properties, in a mineralized solution - sunflower oil with a concentration of 0.5 % and rapeseed oil with a concentration of 3 %, in a saline-saturated solution - rapeseed oil with a concentration of 1 %. Sunflower oil additives showed satisfactory test results only for fresh and mineralized water-clay drilling mud. Compared to sunflower oil, rapeseed oil showed itself when added to all the tested samples. It can be concluded that the introduction of rapeseed oil provides satisfactory anti-fracture and technological indicators for all types of solutions, therefore rapeseed oil was chosen as the basis of the lubricant additive. Technologically appropriate concentrations of oils are in the range from 1 to 3 %. At these oil concentrations, the negative side effect, in particular on the foaming of the solution, is to a lesser extent, the solutions are characterized by a stable consistency over time, and their lubricating properties are improved. The composition of a lubricating additive based on rapeseed oil was developed for the treatment of various types of water-clay drilling mud.

  • FOAM ACID FRACTURE AS AN ALTERNATIVE TO STANDARD FRACKING AND LIQUID-LESS METHODS OF ROCKS LIQUIDATION

    by Yuliya Vitaliyivna Laziebna, Victoriia Ivanivna Dmytrenko

    The article discusses the issue of the resource potential of tight terrigenous gas-saturated reservoirs, which lie at significant depths within the central part of the Dnipro-Donetsk oil and gas-bearing region, and ways to solve problems related to the methods of development of these deposits, since they are non-convective and cannot be extracted by the classical method. Within the scope of this issue, the article considers the method of hydraulic fracturing as one of the most effective ways of causing the inflow of hydrocarbons from the productive horizon and intensifying the development of hard-to-extract deposits. An overview of fracturing substances used for the process of densification of rocks, in particular, liquids based on water, hydrocarbon, acid bases, liquid-free methods and foam systems, was performed. The compositions of the reagents, the features of their use, and their main disadvantages are listed. Examples of world experience in the use of well-known fracturing fluids and fluid-free methods of reservoir densification are given.In this work, attention is focused on increasing the permeability of rocks through the use of foam acid systems, since, as experience shows, they are highly effective in conditions of tightand heterogeneous reservoirs due to their selectivity, they can be adapted to rocks of various lithological and mineralogical composition and a wide range thermo-baric conditions, they have satisfactory transport properties and the ability to cause self-cleaning of the well.The main reasons for popularizing the use of methods of loosening rocks with a minimum liquid content in the composition of explosive substances for unconventional gas deposits of Ukraine are highlighted. It is recommended to carry out work on the creation of more effective, ecological and economically profitable new or improvement of existing disintegrants, especially foam systems.

  • Open Access

    Analysis of the influence of the hydrate-bearing rocks properties on the prospects their industrial development

    by Angela Yelchenko-Lobovska, Oleksandr Lukin, Vasyl Savyk, Victoriіa Dmytrenko

    Along with renewable energy and hydrogen, gas hydrates may become the most significant energy resource in the coming years. The reserves of gas in the hydrate state exceed all the combined world reserves of traditional energy resources. At the same time, the gas hydrates properties in the conditions their natural occurrence in the composition of hydrate-containing rock cause significant difficulties in their extraction. In this regard, the industrial use of colossal renewable gas resources in the gas hydrate state is just beginning. Based on this, the methods of developing gas hydrate deposits are the object of research. Based on the analysis and generalization of the currently known examples results of experimental and industrial development of gas hydrate deposits, as well as the results of studying the hydrate-bearing rocks properties, an assessment of the prospects for the industrial implementation of gas hydrate deposit development methods is given. Extraction of methane from gas hydrate deposits causes difficulties due to their solid form. Existing promising methods of their development involve the dissociation of gas hydrate into gas and water. Currently implemented research and industrial development projects of gas hydrate deposits have shown a number of problems related, first of all, to the instability of the hydrate-bearing rock after dissociation of the gas hydrate (at the same time, in the vast majority, the natural gas hydrate becomes metastable and weakly cemented). Therefore, there is still no commercially attractive technology for obtaining natural gas from gas hydrate deposits. At the same time, the depressurization method is considered the most promising. Based on this, the improvement of the technology of influence on the hydrate-bearing rock for the natural gas extraction should concern the provision of the rock removal the into the well. At the same time, effective and competitive development of marine gas hydrates deposits can be realized only if taking into account the geological features of the distribution of hydrate-bearing rocks, as well as the gas hydrates properties in their natural occurrence.

  • Open Access

    The influence of the gas hydrates morphology on the rate of dissociation and the manifestation of self-preservation in non-equilibrium conditions

    by Victoriia Dmytrenko, Oleksandr Lukin, Vasyl Savyk

    The object for the research was samples of artificially formed gas hydrate of different morphology. Gas hydrates are clathrate compounds of water molecules and hydrate-forming gases. They create significant problems for the oil and gas industry. At the same time, they contain enormous natural gas resources. The study of gas hydrates requires the production of quality samples in laboratory conditions and the availability of appropriate laboratory equipment. However, it is customary to use averaged physical indicators when performing calculations and in works on modeling gas-hydrate processes. At the same time, their morphological differences are not taken into account. Therefore, there is a risk of obtaining distorted research results. Based on this, the paper presents an analysis of the morphological differences of artificially formed gas-hydrate structures depending on the method of their formation. An assessment of the influence of the method of gas hydrate formation and the morphology of artificially formed gas hydrate samples on its stability is also given. In addition, recommendations are provided for choosing a method of forming samples of gas-hydrate structures that simulate natural samples. Gas hydrate samples for research were obtained at a laboratory facility by changing the method of mixing the contents of the reactor. The basis of the research methodology was the analysis of enlarged images of gas hydrate samples. The morphology of the gas hydrate samples was studied through the transparent viewing windows of the reactor. For obtain high-quality images, an optical system with a light source inside the reactor was used. The stability of the gas hydrate samples was investigated with gradual pressure release in the reactor. The difficulty of obtaining adequate samples of artificial gas hydrates for modeling the properties of natural analogues is shown. It is shown that morphological differences in the macro- or microstructure of artificially formed gas hydrate samples can affect the results of research. It was concluded that the results of experimental studies with samples of artificially obtained gas hydrate cannot be considered adequate for real conditions without appropriate corrections.

  • MODELING OF PRODUCING PRESSURE IN HETEROGENEOUS OIL-BEARING RESERVOIRS

    by Mikhail Lubkov, Oksana Zakharchuk, Viktoriia Dmytrenko, Oleksandr Petrash, Вікторія Дмитренко

    Numerical modeling of the distribution of the reservoir pressure drop in the vicinity of an operating well was carried out taking into account the inhomogeneous distribution of filtration characteristics (permeability and oil viscosity) in the near and distant zones of the well operation in order to study the practical aspects of filtration in heterogeneous oil-bearing formations based on a combined finite-element-difference method for non-stationary problem of piezoconductivity. The use of the combined finite-element-difference method enables to combine the advantages of the finite-element method and the finite difference method: to model geometrically complex areas, to find the value at any point of the object under study, while the implicit difference scheme. It is shown that the intensity of filtration processes in the vicinity of the operating well depends mainly on the permeability, and, to a lesser extent, on the viscosity of the oil. Moreover, the influence of the permeability of the oil phase in the remote zone (Rd < 5 m) is greater than the effect in the close zone (Rd > 5 m) of the operating well. In the case of low permeability of the oil phase in the vicinity of the existing well, to maintain stable oil production, it is necessary to place an injection well near the production well. Using the method suggested, it is possible to predict the effect of the injection well on the formation pressure distribution in the formation. The scientific novelty of the work lies in the study of the influence of the heterogeneous permeability and oil viscosity distribution on the reservoir pressures distribution around the wells by modeling filtration processes based on a combined finite-element-difference method. The practical significance of the research results comes down to confirming the close relationship between the heterogeneity of the porous medium and the reservoir pressures distribution around an operating producing well. The combined finite-element-difference method used in this work can be used to solve other filtration problems (for example, to calculate the gas saturation of a reservoir, create a method for calculating well flow rates, assess the effect of injection wells on filtration processes).