Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhuang Li has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Investigation into Stability, Heat Transfer, and Flow Characteristics of TiO2-SiO2 Hybrid Nanofluids Under Multiple Influencing Factors

    by Jiahao Wu, Zhuang Li, Weiwei Jian, Danzhu Ma

    Extensive research and empirical evidence demonstrate that nanofluids enhance heat transfer efficiency in microchannels, but this improvement is often accompanied by increased pressure drop and particle clogging. This study aims to determine the optimal parameters for preparing stable nanofluids and to discuss the effects of different parameters on thermal and hydraulic performance. By analyzing the impact of varying ultrasonication time, particle concentration, particle size, surfactant type, and mixing ratios on stability, the most stable nanofluid was selected for evaluation of flow heat transfer and cost-effectiveness. Results indicate that a 1:1 mixed nanofluid of TiO2 (20 nm)-SiO2 (50 nm) exhibits optimal stability under conditions of 90 min ultrasonication, 0.20 vol% total particle concentration, and 0.15 wt% xanthan gum. At a Reynolds number of 550, this mixed nanofluid exhibits superior thermal performance. Compared with deionized water, its convective heat transfer coefficient and Nusselt number increase by 40.25% and 37.94%, respectively, while the pressure drop rises by only 17.18%. The performance evaluation criterion reaches 1.43, accompanied by a high cost–performance factor. These findings demonstrate that mixing large and small particles of TiO2 and SiO2 not only significantly enhances thermal performance but also positively impacts stability and hydraulic properties. A 90 min ultrasonic treatment time markedly improves stability and optimizes dynamic light scattering results.


  • Open Access

    Ca–Fe Montmorillonite Catalyzed OS Pyrolysis: Features and Thermodynamics

    by Danzhu Ma, Honghu Zhou, Zhuang Li, Boning Yu, Weiwei Jian

    The enhancement of shale oil (SO) yield from oil shale (OS) has emerged as a research focus worldwide. Pyrolysis represents the principal thermochemical approach for converting OS into SO. This study aims to increase SO yield and improve its quality by employing montmorillonite (MMT) as a support to load metal salts CaCl 2 ·4H 2 O, Fe(NO 3 ) 2 ·9H 2 O, and MgCl 2 ·6H 2 O, thereby fabricating MMT‐based metal salt catalysts. The effects of these catalysts on the distribution of pyrolysis products from OS and the characteristics of the resulting liquid fuels were systematically investigated. The results demonstrate that metal salts loaded on MMT collectively enhance SO production. Among all catalyst samples examined, 20Ca‐5MMT exhibited the highest SO yield of approximately 7.26 wt.%. Furthermore, the promotional effect of MMT on aliphatic compound formation in SO establishes a comprehensive catalytic performance ranking: 20Ca‐Fe‐5MMT > 20Ca‐Mg‐5MMT > 20Fe‐Mg‐5MMT.

  • Numerical simulation on molten steel flow in the mold under the effect of vertical traveling wave magnetic field and horizontal steady magnetic field

    by Zhuang Li, Jun Liu, Danzhu Ma

    Electromagnetic braking technology plays a critical role in improving the continuous casting yield and optimizing the quality of the continuous casting slab. This paper introduced a novel electromagnetic braking device that integrates a vertical traveling wave magnetic field with a horizontal steady magnetic field, referred to as VTHS-EMBr. The VTHS-EMBr consists of two pairs of vertical magnetic poles that generate the traveling wave magnetic field and a pair of horizontal magnetic poles that generate the steady magnetic field, which were installed on the wide face close to the narrow face of the mold and beneath the submerged entry nozzle (SEN) of the mold. Numerical simulations were conducted to investigate the characteristics of combined magnetic fields with varying vertical traveling wave magnetic induction intensities, wave frequencies, and different horizontal magnetic induction intensities, as well as their effects on the flow behavior of molten steel and meniscus fluctuations in the mold. The results showed that when the motion direction of the vertical traveling wave magnetic field was downward, the electromagnetic braking force increases significantly with higher applied current and frequency. This effect not only effectively reduced the velocity of molten steel in the upward backflow region, mitigated the impact of upward backflow on the meniscus, and significantly suppressed its fluctuation, but also appropriately increased the impact depth of the downward backflow. Under the casting speed of 2 m/min in this study, the VTHS-EMBr demonstrated effective flow control performance. The research on this novel electromagnetic braking technology provides a theoretical basis and technical support for optimizing traditional electromagnetic braking technologies and developing new electromagnetic braking technologies.


  • Open Access

    Asymmetric Flow Control in a Slab Mold through a New Type of Electromagnetic Field Arrangement

    by Yanming Bao, Zhuang Li, Lintao Zhang, Junxia Wu, Danzhu Ma, Fengrui Jia

    This research aims to investigate the control effect of asymmetric flow in a slab mold using a novel magnetic field arrangement: freestanding adjustable combination electromagnetic brake (FAC-EMBr). Three scenarios (submerged entry nozzle moves to the narrow face, wide face of the slab mold, and rotates 10°) were studied using three-dimensional numerical simulation. The results show that the magnetic field generated by the FAC-EMBr system can effectively cover three key zones in mold and that the magnetic flux density in the zone cover by a vertical magnetic pole can be adjusted according to the actual flow condition. The FAC-EMBr can effectively improve the asymmetric flow in a mold and near the narrow surface caused by the asymmetric arrangement of the nozzle and can effectively inhibit the occurrence of the flow deviation phenomenon and stabilize the steel/slag interface fluctuation. At the same time, FAC-EMBr has obvious inhibition effects on the surface velocity and can optimize the asymmetric distribution of the surface velocity and the upper reflux velocity caused by the asymmetric arrangement of the nozzle. This study can provide theoretical evidence for the development and utilization of a new electromagnetic brake technology.


  • A narrative review: The electromagnetic field arrangement and the “braking” effect of electromagnetic brake (EMBr) technique in slab continuous casting

    by Zhuang Li, Lintao Zhang, Danzhu Ma, Nicholas P. Lavery, Engang Wang

    Electromagnetic brake (EMBr) technique is adopted to reduce the turbulence of molten alloy in the slab mould in the continuous casting process, especially under high casting speed. We introduce a state-of-the-art EMBr technique by reviewing the published literature. The main objective of this paper is to give a clear view of the EMBr technique in terms of the magnet arrangement, along with their “Braking” effect to help decision-making. The EMBr system can be divided into three types, in terms of the magnet arrangement: the Local type, the Ruler type and the Multi-mode type, respectively. Both advantages and disadvantages of each type have been discussed. Further challenges are also raised.


  • Open Access

    Kinetics and thermodynamics of SO2 adsorption on metal-loaded multiwalled carbon nanotubes

    by Shaopeng Zhang, Zhuang Li, Yanchun Yang, Weiwei Jian, Danzhu Ma, Fengrui Jia

    To investigate the adsorption kinetics and thermodynamic adsorption mechanism and laws of dry flue gas desulfurization, we prepared a new adsorbent by loading Cr, Cu, and Zn on TiO2-loaded multiwalled carbon nanotubes. Desulfurization experiments were also carried out. In this study, three kinds of samples were used for simulation and diffusion processes in the dynamic adsorption of different SO2 volume fractions in flue gas and thermodynamic model analysis of different temperatures in flue gas. Results show that the diffusion coefficient of SO2 in three kinds of samples ranges from 10−16 to 10−14 m2 s−1, and the diffusion may be dominated by configuration diffusion. The intraparticle diffusion model predicts that the performance improves with an increase in the SO2 volume fraction and a shift of adsorption time. This finding indicates that an increase in SO2 volume fraction and a change in adsorption time increase the Kundsen diffusion specific gravity and decrease the configuration diffusion specific gravity, thereby increasing the SO2 diffusion resistance, which becomes faster than the activation energy barrier resistance in the catalytic oxidation reaction. Thus, the diffusion resistance specific gravity increases in the total resistance of the diffusion reaction. One possible mechanism of the adsorption process is the transition to surface reaction control at the early stage of adsorption to joint control of late diffusion and surface reactions. Adsorption thermodynamics studies show that SO2 adsorption by three adsorbents is a spontaneous, exothermic, and entropic reduction process, and the increase in temperature is inconducive for SO2 adsorption in three samples.


  • Open Access

    Effects of Metal Oxides on Carbonation and Coking of High-Salinity Organic Wastewater

    by Jumei Ye, Zhuang Li, Chongcong Li, Tianya Li, Ziqiao Gao, Hui Dong

    Slag is difficult to treat quantitatively due to the formation of a molten mixture in the carbonization process of high-salinity organic wastewater. Thus, aiming at solving this difficulty, the effects of metal oxide additives, additive ratio, furnace burden ratio, and carbonization temperature on the carbonization and coking of high-salinity organic wastewater are systematically analyzed. The analysis is performed using scanning electron microscopy, X-ray diffraction, and Vickers hardness tests. The results show that all five metal oxide additives can reduce the hardness of carbonized products. The relative effect of reducing the coked hardness is as follows: . Thus, the effect of MgO on reducing the coking hardness is stronger than that of the other four metal oxides, reducing the hardness of carbonized products by approximately 81%. Furthermore, the adding charge can reduce the hardness index by at least 60%. When the carbonization temperature is higher than 800°C, the hardness index of the carbonized product decreases by approximately 5% each 50°C of increase in temperature. This study shows that the addition of metal oxides can effectively reduce the hardness of coking during the treatment of high-salt organic wastewater by carbonization and oxidation and provide theoretical support for the subsequent treatment of high-salt organic wastewater by carbonization and oxidation.


  • Open Access

    Numerical Simulation on the Brake Effect of FAC-EMBr and EMBrRuler in the Continuous Casting Mold

    by Zhuang Li, Lintao Zhang, Yanming Bao, Danzhu Ma

    The brake effect of the freestanding adjustable combination electromagnetic brake (FAC-EMBr) and EMBr ruler on the behavior of molten steel flow and the level fluctuation were investigated with the numerical method. The effects of the horizontal magnetic pole position (EMBr ruler), magnetic induction intensity, and casting speed on two types of electromagnetic brakes were studied. The numerical simulation results show that the magnetic field caused by the EMBr ruler is mainly distributed under the submerged entry nozzle (SEN), and it is very weak nearby the meniscus area. After the FAC-EMBr is applied, the magnetic field is mainly distributed in the area below the submerged entry nozzle, the upper roll region, and in the meniscus region. The application of the electromagnetic brake can effectively suppress the impact of the jet and decrease the molten steel velocity in the meniscus area. The brake effect of the EMBr ruler on the behavior of the molten steel flow and the level fluctuation is significantly influenced by the horizontal magnetic pole position. The increasing of the magnetic flux density can significantly increase the velocity of molten steel in the upper roll region and lead to an intense fluctuation in the steel/slag interface, as the horizontal magnetic field cannot cover the three key regions. The brake effect of the FAC-EMBr is less influenced by the variation of the process parameters due to the addition of vertical magnetic poles. Additionally, the “secondary braking effect” of the vertical magnetic poles can help to lower the increase of velocity in the upper roll region caused by the excessive magnetic induction intensity and the high casting speed. Therefore, even under the high casting speed conditions, the application of a new type of FAC-EMBr is also an efficient way to suppress the molten steel flow and level fluctuation at the meniscus area and decrease the possibility of slag entrapment.