RMRong Ma

Rong Ma

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rong Ma has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Machine-learning wall model of large-eddy simulation for low- and high-speed flows over rough surfaces

    by Rong Ma, Adrian Lozano-Duran

    We present a wall model for large-eddy simulation that incorporates surface-roughness effects and is applicable across low- and high-speed flows, for both transitional and fully rough conditions. The model, implemented using an artificial neural network, is trained on a direct numerical simulation database of compressible turbulent channel flows over rough walls. The dataset contains 372 cases spanning a wide range of irregular roughness topographies, including Gaussian and Weibull distributions, Mach numbers 0~3.3, and friction Reynolds numbers 180~2000. We employ an information-theoretic, dimensionless learning method to identify the inputs with the highest predictive power for the dimensionless wall friction and wall heat flux. Predictions are accompanied by a confidence score derived from a spectrally normalized neural Gaussian process, which quantifies uncertainty in regions that deviate from the training dataset. The model performance is first evaluated a-priori on 110 turbulent channel flow cases, yielding prediction errors below 4%. The model is assessed a-posteriori in wall-modeled large-eddy simulations across diverse test cases. These include over 160 subsonic and supersonic turbulent channel flows with rough walls, a transonic high-pressure turbine (HPT) blade with Gaussian roughness, a high-speed compression ramp with sandpaper roughness, and three hypersonic blunt bodies with sand-grain roughness. Results show that the proposed wall model typically achieves a-posteriori predictive accuracy within 10% for wall shear stress and within 15% for wall heat flux, with high confidence in the channel flows and HPT blade cases. In the rough-wall compression ramp and hypersonic blunt bodies, the model captures the heating augmentation with errors ranging 0%~20%. In the cases with the highest errors, the reduced performance is correctly detected by a drop in the confidence score.

  • Open Access

    Machine-learning wall-model large-eddy simulation accounting for isotropic roughness under local equilibrium

    by Rong Ma, Adrián Lozano-Durán

    We introduce a wall model for large-eddy simulation (WMLES) applicable to rough surfaces with Gaussian and non-Gaussian distributions for both the transitionally and fully rough regimes. The model is applicable to arbitrary complex geometries where roughness elements are assumed to be underresolved, i.e. subgrid-scale roughness. The wall model is implemented using a multi-hidden-layer feedforward neural network, with the mean geometric properties of the roughness topology and near-wall flow quantities serving as input. The optimal set of non-dimensional input features is identified using information theory, selecting variables that maximize information about the output while minimizing redundancy among inputs. The model also incorporates a confidence score based on Gaussian process modelling, enabling the detection of potentially low model performance for untrained rough surfaces. The model is trained using a direct numerical simulation (DNS) roughness database comprising approximately 200 cases. The roughness geometries for the database are selected from a large repository through active learning. This approach ensures that the rough surfaces incorporated into the database are the most informative, achieving higher model performance with fewer DNS cases compared with passive learning techniques. The performance of the model is evaluated both apriori and aposteriori in WMLES of turbulent channel flows with rough walls. Over 550 channel flow cases are considered, including untrained roughness geometries, roughness Reynolds numbers and grid resolutions for both transitionally and fully rough regimes. Our rough-wall model offers higher accuracy than existing models, generally predicting wall shear stress within an accuracy range of 1%–15 %. The performance of the model is also assessed on a high-pressure turbine blade with two different rough surfaces. We show that the new wall model predicts the skin friction and the mean velocity deficit induced by the rough surface on the blade within 1%–10 % accuracy except the region with transition or shock waves. This work extends the building-block flow wall model (BFWM) introduced by Lozano-Durán & Bae (2023. J. Fluid Mech.963, A35) for smooth walls, expanding the BFWM framework to account for rough-wall scenarios.


  • Open Access

    Boundary layer transition due to distributed roughness: effect of roughness spacing

    by Rong Ma, Krishnan Mahesh

    The influence of roughness spacing on boundary layer transition over distributed roughness elements is studied using direct numerical simulation and global stability analysis, and compared with isolated roughness elements at the same Reynolds number $Re_h=U_eh/\nu$ ( $U_e$ is the boundary layer edge velocity, h is roughness height and $\nu$ is the kinetic viscosity of the fluid). Small spanwise spacing ( $\lambda _z=2.5h$ ) inhibits the formation of counter-rotating vortex pairs (CVP) and, as a result, hairpin vortices are not generated and the downstream shear layer is steady. For $\lambda _z=5h$ , the CVP and hairpin vortices are induced by the first row of roughness, perturbing the downstream shear layer and causing transition. The temporal periodicity of the primary hairpin vortices appears to be independent of the streamwise spacing. Distributed roughness leads to a lower critical roughness Reynolds number for instability to occur and a more significant breakdown of the boundary layer compared with isolated roughness. When the streamwise spacing is $\lambda _x=5h$ , the high-momentum fluid barely moves downward into the cavities and the wake flow has little impact on the following roughness elements. The leading unstable varicose mode is associated with the central low-speed streaks along the aligned roughness elements, and its frequency is close to the shedding frequency of hairpin vortices in the isolated case. For larger streamwise spacing ( $\lambda _x=10h$ ), two distinct modes are obtained from global stability analysis. The first mode shows varicose symmetry, corresponding to the primary hairpin vortex shedding induced by the first-row roughness. The high-speed streaks formed in the longitudinal grooves are also found to be unstable and interact with the varicose mode. The second mode is a sinuous mode with lower frequency, induced as the wake flow of the first-row roughness runs into the second row. It extracts most energy from the spanwise shear between the high- and low-speed streaks.


  • Open Access

    Global stability analysis and direct numerical simulation of boundary layers with an isolated roughness element

    by Rong Ma, Krishnan Mahesh

    Global stability analysis and direct numerical simulation (DNS) are used to study boundary layer flows with an isolated roughness element. The aspect ratio of the element ( $\eta$ ) is small, while the ratio of element height to displacement boundary layer thickness ( $h/\delta ^{*}$ ) is large. Both steady base flows and time-averaged mean flows are able to capture the frequencies of the primary vortical structures and mode shapes. Global stability results highlight that although the varicose instability is dominant for large $h/\delta ^{*}$ , sinuous instability becomes more pronounced as $Re_h$ increases for the thin geometry ( $\eta =0.5$ ), due to increased spanwise shear in the near-wake region. Wavemaker results indicate that $\eta$ affects the convective nature of the shear layer more than the type of instability. DNS results show that different instability mechanisms lead to different development and evolution of vortical structures in the transition process. For $\eta =1$ , the varicose instability is associated with the periodic shedding of hairpin vortices, and its stronger spatial transient growth indicated by wavemaker results aids the formation of hairpin vortices farther downstream. In contrast, for $\eta =0.5$ , the interplay between varicose and sinuous instabilities results in a broader-banded energy spectrum and leads to the sinuous wiggling of hairpin vortices in the near wake when $Re_h$ is sufficiently high. A sinuous mode with a lower frequency captured by dynamic mode decomposition analysis, and associated with the ‘wiggling’ of streaks, persists far downstream and promotes transition to turbulence. A new regime map is developed to classify and predict instability mechanisms based on $Re_{hh}^{1/2}$ and $d/\delta ^{*}$ using a logistic regression model. Although the mean skin friction demonstrates different evolutions for the two geometries, both of them efficiently trip the flow to turbulence at $Re_h=1100$ . An earlier location of a fully-developed turbulent state is established for $\eta =1$ at $x \approx 110h$ .


  • Direct numerical simulation of turbulent channel flow over random rough surfaces

    by Rong Ma, Karim Alamé, Krishnan Mahesh

    Direct numerical simulation of flow in a turbulent channel with a random rough bottom wall is performed at friction Reynolds number . The rough surface corresponds to the experiments of Flack et al. (Flow Turbul. Combust., vol. 104, 2020, pp. 317–329). The computed skin-friction coefficients and the roughness functions show good agreement with experimental results. The double-averaging methodology is used to investigate mean velocity, Reynolds stresses, dispersive flux and mean momentum balance. The roll-up of the shear layer on the roughness crests is identified as a primary contributor to the wall-normal momentum transfer. The mean-square pressure fluctuations increase in the roughness layer and collapse onto their smooth-wall levels away from the wall. The dominant source terms in the pressure Poisson equation are examined. The rapid term shows that high pressure fluctuations observed in front of and above the roughness elements are mainly due to the attached shear layer formed upstream of the protrusions. The contribution of the slow term is smaller. The slow term is primarily increased in the troughs and in front of the roughness elements, corresponding to the occurrence of quasi-streamwise vortices and secondary vortical structures. The mean wall shear on the rough surface is highly correlated with the roughness height, and depends on the local roughness topography. The probability distribution function of wall shear stress fluctuations is consistent with higher velocities at roughness crests and reverse flow in the valley regions. Extreme events are more probable due to the roughness. Events with comparable magnitudes of the streamwise and spanwise wall shear stress occur more frequently, corresponding to a more isotropic vorticity field in the roughness layer.