Seung-Yong Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seung-Yong Lee has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Chikako Takushima
4 shared publicationsJun-Ichi Hamada
4 shared publications- Nobuo Nakada
Department of Materials Science and Engineering, Institute of Science Tokyo
3 shared publications - Bong Cheon Park
Materials Data & Analysis Research Division, Korea Institute of Materials Science, Changwon 51508, Republic of Korea
2 shared publications Ritupan Sarmah
2 shared publicationsSita Chettri
2 shared publications
Latest Publications
- Open Access
Effects of Joint-Edge Preparation on Weld Quality and Mechanical Properties of Thin AISI 304 Stainless Steel Sheets Under Autogenous and Filler-Wire Laser Beam Welding Conditions
Laser beam welding (LBW) offers low thermal distortion for thin austenitic stainless steel sheets but is sensitive to butt-joint fit-up and edge quality. This study compared machined and sheared joint edges under selected autogenous and ER308L filler-wire LBW conditions. Bead geometry, defects, microstructure, microhardness, tensile properties, and fracture behavior were characterized using conventional microscopy, EBSD-KAM, and three-dimensional digital image correlation (3D-DIC). The machined-edge autogenous condition (LBW-A-M) produced a stable bead with 0.04 mm top underfill and only a small number of internal discontinuities, while its tensile properties remained close to those of the base metal and fracture occurred in the base metal. In contrast, the sheared-edge autogenous condition (LBW-A-S) exhibited 0.24 mm top underfill, 0.18 mm misalignment, multiple pores, and localized strain near the weld, with tensile strength and elongation of 682.31 MPa and 44.04%, respectively. Under the selected filler-wire conditions, no measurable top underfill was observed, although pores remained. Because the autogenous and filler-wire modes used different process parameters and heat inputs, cross-mode differences are condition-specific rather than isolated filler-wire effects. Overall, joint-edge preparation and fit-up control remained important for thin-sheet LBW.
Open AccessEffects of Joint-Edge Preparation on Weld Quality and Mechanical Properties of Thin AISI 304 Stainless Steel Sheets Under Autogenous and Filler-Wire Laser Beam Welding Conditions
Laser beam welding (LBW) offers low thermal distortion for thin austenitic stainless steel sheets but is sensitive to butt-joint fit-up and edge quality. This study compared machined and sheared joint edges under selected autogenous and ER308L filler-wire LBW conditions. Bead geometry, defects, microstructure, microhardness, tensile properties, and fracture behavior were characterized using conventional microscopy, EBSD-KAM, and three-dimensional digital image correlation (3D-DIC). The machined-edge autogenous condition (LBW-A-M) produced a stable bead with 0.04 mm top underfill and only a small number of internal discontinuities, while its tensile properties remained close to those of the base metal and fracture occurred in the base metal. In contrast, the sheared-edge autogenous condition (LBW-A-S) exhibited 0.24 mm top underfill, 0.18 mm misalignment, multiple pores, and localized strain near the weld, with tensile strength and elongation of 682.31 MPa and 44.04%, respectively. Under the selected filler-wire conditions, no measurable top underfill was observed, although pores remained. Because the autogenous and filler-wire modes used different process parameters and heat inputs, cross-mode differences are condition-specific rather than isolated filler-wire effects. Overall, joint-edge preparation and fit-up control remained important for thin-sheet LBW.
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Multiscale failure mechanism of Armox 500T and 600T under complete ballistic perforation: Three-dimensional damage morphology and adiabatic shear band-assisted cracking
In this study, the perforation behaviors of commercial Armox 500T and Armox 600T were investigated under various projectile velocities. The failure mechanisms were analyzed from the macroscopic to the nanoscale using X-ray computed tomography (X-ray CT), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Under complete perforation conditions, Armox 600T exhibited greater initial resistance owing to its higher hardness but suffered severe rear-side damage (plugging and spalling). By contrast, Armox 500T exhibited extensive ductile hole expansion, maintaining a residual volume of approximately 99%. Microstructural characterization demonstrated that adiabatic shear bands (ASBs) were prominent near the perforation surfaces and along the radial cracks in both steels. The occurrence of dynamic recrystallization and even localized melting inside the ASBs induced microcracks along the ASB/matrix interfaces and prior austenite grain (PAG) boundaries, eventually coalescing into the observed macroscopic radial cracks. These findings suggest that the design of high-performance armor steels should be based on an optimized balance between hardness and dynamic damage tolerance.
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMultiscale failure mechanism of Armox 500T and 600T under complete ballistic perforation: Three-dimensional damage morphology and adiabatic shear band-assisted cracking
In this study, the perforation behaviors of commercial Armox 500T and Armox 600T were investigated under various projectile velocities. The failure mechanisms were analyzed from the macroscopic to the nanoscale using X-ray computed tomography (X-ray CT), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Under complete perforation conditions, Armox 600T exhibited greater initial resistance owing to its higher hardness but suffered severe rear-side damage (plugging and spalling). By contrast, Armox 500T exhibited extensive ductile hole expansion, maintaining a residual volume of approximately 99%. Microstructural characterization demonstrated that adiabatic shear bands (ASBs) were prominent near the perforation surfaces and along the radial cracks in both steels. The occurrence of dynamic recrystallization and even localized melting inside the ASBs induced microcracks along the ASB/matrix interfaces and prior austenite grain (PAG) boundaries, eventually coalescing into the observed macroscopic radial cracks. These findings suggest that the design of high-performance armor steels should be based on an optimized balance between hardness and dynamic damage tolerance.
- Open Access
- 25 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of build height on microstructure and mechanical properties of AlSi10Mg alloy fabricated by laser powder bed fusion
This work investigated build-height-dependent variation of microstructure and mechanical properties in AlSi10Mg alloy fabricated by laser powder bed fusion (LPBF). Increasing height reduces tensile strength and hardness, with coarsening of solidification cells. These variations were associated with build-height-dependent thermal history during LPBF, providing guidance for achieving more uniform properties in large-scale AlSi10Mg components.
- 25 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of build height on microstructure and mechanical properties of AlSi10Mg alloy fabricated by laser powder bed fusion
This work investigated build-height-dependent variation of microstructure and mechanical properties in AlSi10Mg alloy fabricated by laser powder bed fusion (LPBF). Increasing height reduces tensile strength and hardness, with coarsening of solidification cells. These variations were associated with build-height-dependent thermal history during LPBF, providing guidance for achieving more uniform properties in large-scale AlSi10Mg components.
- Open Access
- 30 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 2071-2079
Effects of grain size and interstitial elements on the Portevin–Le Chatelier effect in austenitic stainless steels
- 30 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 40, 2071-2079
Open AccessEffects of grain size and interstitial elements on the Portevin–Le Chatelier effect in austenitic stainless steels
- Open Access
- 17 February 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (9) , 6342-6346
Characterization of densification behavior and mechanical properties of solid electrolyte powders for all solid-state batteries
BH4-substituted argyrodite solid electrolytes are mechanically softer and achieve near-theoretical density at lower pressures and room temperature compared to Cl- or Br-substituted counterparts, which is consistent with nanoindentation test results.
- 17 February 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (9) , 6342-6346
Open AccessCharacterization of densification behavior and mechanical properties of solid electrolyte powders for all solid-state batteries
BH4-substituted argyrodite solid electrolytes are mechanically softer and achieve near-theoretical density at lower pressures and room temperature compared to Cl- or Br-substituted counterparts, which is consistent with nanoindentation test results.
- 11 July 2022
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 133, 154-164
Serrated flow accompanied with dynamic type transition of the Portevin–Le Chatelier effect in austenitic stainless steel
- 11 July 2022
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 133, 154-164
Serrated flow accompanied with dynamic type transition of the Portevin–Le Chatelier effect in austenitic stainless steel
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Serrated Flow Accompanied with Dynamic Type Transition of the Portevin–Le Chatelier Effect in Austenitic Stainless Steel
The dynamic type transitions of the Portevin–Le Chatelier (PLC) effect were investigated in an Fe–19Cr–13Ni–0.2C austenitic stainless steel by using high-temperature tensile testing equipped with a digital image correlation (DIC) system while considering the corresponding relationship between serrated flow and PLC band behavior. Different types of serration appeared in the stress–strain curve at temperatures from 473 K to 623 K, even at a constant applied strain rate, and the type transition took place dynamically in a certain order with deformation time. DIC analysis revealed that the PLC band propagation behavior also changed in accordance with the dynamic transition of serration type and that the transition of the PLC band propagation behavior could be attributed to the PLC band nucleation manner: 'jumping' PLC band with C-type serration, 'hopping' PLC band with B-type serration, and 'walking' PLC band with A-type serration. In addition, it was found that the dynamic transition of the PLC effect was closely related to the dynamic variation in the global strain rate of the gauge part of the specimen with time. Furthermore, numerical modeling proved that the nucleation manner of PLC band nucleation changed in the order of jumping, hopping, and walking as the strain rate increased owing to the spatial-temporal coupling effect.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessSerrated Flow Accompanied with Dynamic Type Transition of the Portevin–Le Chatelier Effect in Austenitic Stainless Steel
The dynamic type transitions of the Portevin–Le Chatelier (PLC) effect were investigated in an Fe–19Cr–13Ni–0.2C austenitic stainless steel by using high-temperature tensile testing equipped with a digital image correlation (DIC) system while considering the corresponding relationship between serrated flow and PLC band behavior. Different types of serration appeared in the stress–strain curve at temperatures from 473 K to 623 K, even at a constant applied strain rate, and the type transition took place dynamically in a certain order with deformation time. DIC analysis revealed that the PLC band propagation behavior also changed in accordance with the dynamic transition of serration type and that the transition of the PLC band propagation behavior could be attributed to the PLC band nucleation manner: 'jumping' PLC band with C-type serration, 'hopping' PLC band with B-type serration, and 'walking' PLC band with A-type serration. In addition, it was found that the dynamic transition of the PLC effect was closely related to the dynamic variation in the global strain rate of the gauge part of the specimen with time. Furthermore, numerical modeling proved that the nucleation manner of PLC band nucleation changed in the order of jumping, hopping, and walking as the strain rate increased owing to the spatial-temporal coupling effect.
- Open Access
- 1 July 2016
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 26 (7) , 353-358
Hydrogen Embrittlement of Two Austenitic High-Manganese Steels Using Tensile Testing under High-Pressure Gaseous Hydrogen
- 1 July 2016
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 26 (7) , 353-358
Open AccessHydrogen Embrittlement of Two Austenitic High-Manganese Steels Using Tensile Testing under High-Pressure Gaseous Hydrogen