Nina Zh. Shkaruba
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Nina Zh. Shkaruba has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Oleg A. Leonov
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
24 shared publications - Yu. G. Vergazova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
6 shared publications - Galina Temasova
Российский государственный аграрный университет – МСХА имени К.А. Тимирязева
5 shared publications - Lavrentii Grinchenko
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
5 shared publications Timirâzevskaâ Selʹskohozâjstvennaâ Akademiâ
4 shared publicationsЮ. Г. Вергазова
Российский государственный аграрный университет – МСХА имени К.А. Тимирязева
3 shared publications
Latest Publications
- 1 June 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (6) , 382-386
Evaluation of the Variability of Measurement Processes in Control of Wear of Crankshaft Jack Diameters
The article discusses a methodology for collecting and processing measurement information on the main static characteristics used to assess the quality and acceptability of measurement processes in relation to repair production. When assessing the convergence and reproducibility of the measurement process, the dispersion method was used, since this method allows for a more detailed analysis. The methodology for assessing the quality of measurements allows us to determine the acceptability of the methods and measuring instruments recommended in regulatory documentation. As a result of the study, it was found that the greatest contribution to variability of the process of measuring the diameters of worn crankshaft journals is made by sample variability. The second greatest influence on the variability the measuring process is exerted by measuring instruments.
- 1 June 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (6) , 382-386
Evaluation of the Variability of Measurement Processes in Control of Wear of Crankshaft Jack Diameters
The article discusses a methodology for collecting and processing measurement information on the main static characteristics used to assess the quality and acceptability of measurement processes in relation to repair production. When assessing the convergence and reproducibility of the measurement process, the dispersion method was used, since this method allows for a more detailed analysis. The methodology for assessing the quality of measurements allows us to determine the acceptability of the methods and measuring instruments recommended in regulatory documentation. As a result of the study, it was found that the greatest contribution to variability of the process of measuring the diameters of worn crankshaft journals is made by sample variability. The second greatest influence on the variability the measuring process is exerted by measuring instruments.
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 381-385
Study of Interference Dispersion Parameters in the Joint of the YAMZ Gearbox Shaft Output End and a Seal
The service life of the shaft–seal joint in agricultural machinery affects the overall operating life of the assembly. An analysis of factors influencing the durability of the shaft–seal joint revealed the need to investigate the quality of forming the initial interference-fit range in the joint and its compliance with the dimensional interchangeability parameters specified in the design documentation at the assembly design stage. The study aimed to evaluate the probabilistic characteristics of dimensional dispersion for the inner diameter of the seal and the outer diameter of the gearbox flange of the YaMZ-239 transmission. The study examined 100 flanges and 100 seals of type 1.2–100 × 125–12. Measurements of shaft-end diameters were made using an SRP 100-0.001 lever caliper. A DIP-6 instrument with an NIIK-890 system determined the inner diameter of the seals. An assessment of the dispersion parameters of the surface dimensions of the YaMZ-239 gearbox output shaft for the 100h10 seal seat showed that shaft manufacturing achieved process accuracy higher than required, with satisfactory process centering and exhibited a shift toward correctable defects. An investigation of the inner diameter of the seals showed good accuracy of the diameter-forming process, satisfactory process centering, and a slight shift toward non-correctable defects; however, no actual defects occurred. The analysis of interference dispersion showed that the probable percentage of defective joints, as a durability characteristic, equaled 0.01%. The results demonstrate that the manufacturing accuracy of the parts forming the flange–seal joint meets the specified requirements. Therefore, engineers should attribute emerging problems with lubricant leakage from seals to the wear-resistance parameters of these parts and to an analysis of wear in the influencing dimensions that form the dimensional chain, where misalignment deviation and shaft radial runout relative to the seal diameter act as the initial closing links.
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 381-385
Study of Interference Dispersion Parameters in the Joint of the YAMZ Gearbox Shaft Output End and a Seal
The service life of the shaft–seal joint in agricultural machinery affects the overall operating life of the assembly. An analysis of factors influencing the durability of the shaft–seal joint revealed the need to investigate the quality of forming the initial interference-fit range in the joint and its compliance with the dimensional interchangeability parameters specified in the design documentation at the assembly design stage. The study aimed to evaluate the probabilistic characteristics of dimensional dispersion for the inner diameter of the seal and the outer diameter of the gearbox flange of the YaMZ-239 transmission. The study examined 100 flanges and 100 seals of type 1.2–100 × 125–12. Measurements of shaft-end diameters were made using an SRP 100-0.001 lever caliper. A DIP-6 instrument with an NIIK-890 system determined the inner diameter of the seals. An assessment of the dispersion parameters of the surface dimensions of the YaMZ-239 gearbox output shaft for the 100h10 seal seat showed that shaft manufacturing achieved process accuracy higher than required, with satisfactory process centering and exhibited a shift toward correctable defects. An investigation of the inner diameter of the seals showed good accuracy of the diameter-forming process, satisfactory process centering, and a slight shift toward non-correctable defects; however, no actual defects occurred. The analysis of interference dispersion showed that the probable percentage of defective joints, as a durability characteristic, equaled 0.01%. The results demonstrate that the manufacturing accuracy of the parts forming the flange–seal joint meets the specified requirements. Therefore, engineers should attribute emerging problems with lubricant leakage from seals to the wear-resistance parameters of these parts and to an analysis of wear in the influencing dimensions that form the dimensional chain, where misalignment deviation and shaft radial runout relative to the seal diameter act as the initial closing links.
- 1 June 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (6) , 704-709
Calculation of Total Misalignment of a Gearbox Output Shaft Relative to the Seal
The article presents calculation of the dimensional chain for the shaft-seal coupling in which the master link contains misalignment and radial runout of t
- 1 June 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (6) , 704-709
Calculation of Total Misalignment of a Gearbox Output Shaft Relative to the Seal
The article presents calculation of the dimensional chain for the shaft-seal coupling in which the master link contains misalignment and radial runout of t
- 1 January 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (1) , 36-40
Ensuring Accurate Alignment of Gearbox Shaft Axes Using the Compensation Method
For the problem of ensuring accurate coaxial alignment of the shafts of gearboxes N.094.44.000-323 and N.090.20.000-121 of potato harvester KPK-2-01, a dim
- 1 January 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (1) , 36-40
Ensuring Accurate Alignment of Gearbox Shaft Axes Using the Compensation Method
For the problem of ensuring accurate coaxial alignment of the shafts of gearboxes N.094.44.000-323 and N.090.20.000-121 of potato harvester KPK-2-01, a dim
- Open Access
- 1 January 2025
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 27 (2) , 70-76
Study of interference dispersion parameters in the joint of the YAMZ gearbox shaft output end and a seal
Durable operation of the “shaft-seal” joint in agricultural machines affects their service life. The analysis of factors affecting the durability of the “shaft-seal” joint has revealed the need to study the quality of the initial tension range in the “shaft-seal” joint and their compliance with the parameters of dimensional interchangeability, preset in the design documentation. The research purpose is to evaluate the probabilistic characteristics of the dispersion of joints of the inner diameter of the seal and the outer diameter of the flange of the transmission gearbox YAMZ-239. The study involved 100 flanges and 100 seals 1.2-100×125-12. The diameters of shaft ends were measured using a lever bracket SRP 100-0,001. The inner diameter of the seals was determined with a DIP-6 instrument and the NIIK-890 system. The conducted estimation of the dispersion parameters of the surface dimensions of the gearbox output shaft of YAMZ-239 under the 100h10 seal showed that shaft manufacturing provides a technological accuracy above the required level with satisfactory adjustment. However, there is a growing probability of a correctable defect. The study of the inner diameter of the seals showed that the accuracy of forming the inner diameter of the seals is good, the process adjustment is satisfactory; there is a slight shift towards a probability of an uncorrectable defect, but the defect itself is absent. The conducted analysis of tension dispersion showed that the probable percentage of defective joints, as a durability indicator, was 0.01%. The study found that the accuracy of manufacturing the “flange-seal” joint parts meets the specified requirements. The problems with the lubricant leakage from the seals should be solved based on the parameters of wear resistance of these parts, as well the wear analysis of the influencing dimensions that form a dimensional chain. In this chain, the initial closing link is the deviation from alignment and radial runout of the shaft in relation to the seal diameter.
- 1 January 2025
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 27 (2) , 70-76
Open AccessStudy of interference dispersion parameters in the joint of the YAMZ gearbox shaft output end and a seal
Durable operation of the “shaft-seal” joint in agricultural machines affects their service life. The analysis of factors affecting the durability of the “shaft-seal” joint has revealed the need to study the quality of the initial tension range in the “shaft-seal” joint and their compliance with the parameters of dimensional interchangeability, preset in the design documentation. The research purpose is to evaluate the probabilistic characteristics of the dispersion of joints of the inner diameter of the seal and the outer diameter of the flange of the transmission gearbox YAMZ-239. The study involved 100 flanges and 100 seals 1.2-100×125-12. The diameters of shaft ends were measured using a lever bracket SRP 100-0,001. The inner diameter of the seals was determined with a DIP-6 instrument and the NIIK-890 system. The conducted estimation of the dispersion parameters of the surface dimensions of the gearbox output shaft of YAMZ-239 under the 100h10 seal showed that shaft manufacturing provides a technological accuracy above the required level with satisfactory adjustment. However, there is a growing probability of a correctable defect. The study of the inner diameter of the seals showed that the accuracy of forming the inner diameter of the seals is good, the process adjustment is satisfactory; there is a slight shift towards a probability of an uncorrectable defect, but the defect itself is absent. The conducted analysis of tension dispersion showed that the probable percentage of defective joints, as a durability indicator, was 0.01%. The study found that the accuracy of manufacturing the “flange-seal” joint parts meets the specified requirements. The problems with the lubricant leakage from the seals should be solved based on the parameters of wear resistance of these parts, as well the wear analysis of the influencing dimensions that form a dimensional chain. In this chain, the initial closing link is the deviation from alignment and radial runout of the shaft in relation to the seal diameter.
- 30 June 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 27, 108-112
Calculation of the maximum functional clearance of a cylindrical joint between a steel shaft and a cast iron sprocket
Cylindrical joints are widely used in mechanical engineering, where cast iron (sprockets of chain gears, gears, pulleys, etc.) act as the material for making holes, and steel is used for shafts. As a rule, these joints work in the conditions of dry and boundary friction and, in some cases, they have a key. The analysis showed that the wear of such joints occurred mainly due to the discrepancy between the accuracy standards, which, along with the strength standards, determine the durability and reliability of the joints. And if the strength standards are laid down by the designer, then the accuracy standards are usually assigned by analogy, based on the previous experience of using such constructions, with the use of software, when designer inserts standard deviations of shaft and hole as well as fit in electronic drawings. The main factors determining the margin of safety are such characteristics of the material as the maximal stresses on the cut, crumpling, bending, twisting, etc. To determine the margin of accuracy, it is necessary to set such parameters as the largest functional clearance or interference. Currently, there is no method for calculating the maximum functional clearance for joints with boundary or dry friction. The authors obtained dependence for determining the maximal functional clearance by the criterion of exceeding the allowable normal pressure on the contacting surfaces. An example of calculating the accuracy parameters for connecting a shaft made of steel with a malleable cast iron sprocket is considered, for which the maximal functional clearance is determined and fits are assigned – the first of the preferred series, and the second according to the criterion of reducing the cost of finishing processing of the components.
- 30 June 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 27, 108-112
Calculation of the maximum functional clearance of a cylindrical joint between a steel shaft and a cast iron sprocket
Cylindrical joints are widely used in mechanical engineering, where cast iron (sprockets of chain gears, gears, pulleys, etc.) act as the material for making holes, and steel is used for shafts. As a rule, these joints work in the conditions of dry and boundary friction and, in some cases, they have a key. The analysis showed that the wear of such joints occurred mainly due to the discrepancy between the accuracy standards, which, along with the strength standards, determine the durability and reliability of the joints. And if the strength standards are laid down by the designer, then the accuracy standards are usually assigned by analogy, based on the previous experience of using such constructions, with the use of software, when designer inserts standard deviations of shaft and hole as well as fit in electronic drawings. The main factors determining the margin of safety are such characteristics of the material as the maximal stresses on the cut, crumpling, bending, twisting, etc. To determine the margin of accuracy, it is necessary to set such parameters as the largest functional clearance or interference. Currently, there is no method for calculating the maximum functional clearance for joints with boundary or dry friction. The authors obtained dependence for determining the maximal functional clearance by the criterion of exceeding the allowable normal pressure on the contacting surfaces. An example of calculating the accuracy parameters for connecting a shaft made of steel with a malleable cast iron sprocket is considered, for which the maximal functional clearance is determined and fits are assigned – the first of the preferred series, and the second according to the criterion of reducing the cost of finishing processing of the components.
- 1 February 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (2) , 184-188
Calculation and Selection of Interference Fits for Restoring the Shaft Surface under the Sealing Ring by Pressing Thin-Walled Bushings
Methods for restoring shaft surfaces to nominal sizes are analyzed. It is recommended to use the thin-walled bushing method. The research used the principl
- 1 February 2024
- Published by Allerton Press in Russian Engineering Research
- Vol. 44 (2) , 184-188
Calculation and Selection of Interference Fits for Restoring the Shaft Surface under the Sealing Ring by Pressing Thin-Walled Bushings
Methods for restoring shaft surfaces to nominal sizes are analyzed. It is recommended to use the thin-walled bushing method. The research used the principl
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3021 (1) , 040014
Evaluation of the economic efficiency of the use of aggregate equipment in mechanical engineering
The article discusses the issues of assessing the economic efficiency of one of the main directions of the development of modern technologies based on unificati The article discusses the issues of assessing the economic efficiency of one of the main directions of the development of modern technologies based on unificati
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3021 (1) , 040014
Evaluation of the economic efficiency of the use of aggregate equipment in mechanical engineering
The article discusses the issues of assessing the economic efficiency of one of the main directions of the development of modern technologies based on unificati The article discusses the issues of assessing the economic efficiency of one of the main directions of the development of modern technologies based on unificati
- Open Access
- 1 January 2024
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 26 (5) , 39-46
Assessment of the quality of the crankshaft grinding process for repair size
Mechanical processing of critical parts affects the quality of engine repair. The authors carried out research to assess the quality of setting for machining the crankshaft main journals of the ZMZ engine for the repair size. They studied the diameters of 20 crankshaft main journals of the ZMZ engine after machining for the repair size. The diameters were controlled by a lever clamp SR-75. The following tools were sequentially used to evaluate the quality of machining main bearing journals: a “box-and-whisker” diagram, Shewhart control charts, and a histogram. According to the “Box and Whiskers” diagram it was found that after machining for the repair size all the journals have a diameter within the machining tolerance field, but at the same time there is a scatter between the diameters of the journals of the same crankshaft. After analyzing the Shewhart control charts, it was found that the scatter values within one subgroup (crankshaft) and between the subgroups were caused by the usual reasons, and this scatter pattern can be considered random. Consequently, the technological process can be considered stable and controllable. The histogram helped to determine the probability of correctable rejects after machining of the engine journal for the repair size, equal to 1.95%, and the probability of irreparable rejects, equal to 0. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. Over time, the index will decrease and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is desirable to regularly check the quality of machining crankshaft main journals for the repair size, consistently applying all the three tools to identify the size variation and inconsistencies, which is especially relevant for worn equipment.
- 1 January 2024
- Published by Russian State Agrarian University - Moscow Timiryazev Agricultural Academy in Agricultural engineering
- Vol. 26 (5) , 39-46
Open AccessAssessment of the quality of the crankshaft grinding process for repair size
Mechanical processing of critical parts affects the quality of engine repair. The authors carried out research to assess the quality of setting for machining the crankshaft main journals of the ZMZ engine for the repair size. They studied the diameters of 20 crankshaft main journals of the ZMZ engine after machining for the repair size. The diameters were controlled by a lever clamp SR-75. The following tools were sequentially used to evaluate the quality of machining main bearing journals: a “box-and-whisker” diagram, Shewhart control charts, and a histogram. According to the “Box and Whiskers” diagram it was found that after machining for the repair size all the journals have a diameter within the machining tolerance field, but at the same time there is a scatter between the diameters of the journals of the same crankshaft. After analyzing the Shewhart control charts, it was found that the scatter values within one subgroup (crankshaft) and between the subgroups were caused by the usual reasons, and this scatter pattern can be considered random. Consequently, the technological process can be considered stable and controllable. The histogram helped to determine the probability of correctable rejects after machining of the engine journal for the repair size, equal to 1.95%, and the probability of irreparable rejects, equal to 0. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. Over time, the index will decrease and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is desirable to regularly check the quality of machining crankshaft main journals for the repair size, consistently applying all the three tools to identify the size variation and inconsistencies, which is especially relevant for worn equipment.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3102 (1)
Method for completing the parts connections of the shaft-seal
Various studies devoted to the issues of quality assurance, reliability and durability of sealing units used in various machines and mechanisms have consid Various studies devoted to the issues of quality assurance, reliability and durability of sealing units used in various machines and mechanisms have consid
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3102 (1)
Open AccessMethod for completing the parts connections of the shaft-seal
Various studies devoted to the issues of quality assurance, reliability and durability of sealing units used in various machines and mechanisms have consid Various studies devoted to the issues of quality assurance, reliability and durability of sealing units used in various machines and mechanisms have consid