Oleg A. Leonov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Oleg A. Leonov has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Nina Zh. Shkaruba
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
24 shared publications N. Zh. Shkaruba
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
21 shared publicationsYu. G. Vergazova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
16 shared publicationsN Zh Shkaruba
Department of Metrology, standardization and quality management, Russian State Agrarian University - Moscow Timiryazev Agricultural Academy, 49, Timiryazevskaya, Moscow, 127550, Russia
10 shared publications- Galina Temasova
Российский государственный аграрный университет – МСХА имени К.А. Тимирязева
8 shared publications - Yu. G. Vergazova
Russian State Agrarian University—Moscow Timiryazev Agricultural Academy, Moscow, Russia
7 shared publications
Latest Publications
- 1 June 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (6) , 378-381
Evaluation of the Quality of the Process of Controlling the Process of the Front Journal of the Intermediate Shaft with a Caliper Gauge during Repairs of a ZMZ Engine
The procedure and sequence of quality assessment of processes of controlling carried out during machine repair are considered. The quality of the process of controlling the intermediate shaft diameter of a ZMZ engine using a caliper gauge was assessed. As a result of mathematical processing of the data, it was revealed that the process of control with a caliper gauge can be considered acceptable. Replacing the micrometer with a caliper gauge will not only improve the accuracy of control, but also significantly reduce the labor intensity of the work, which will ensure the quality of the assembly of the connection of the front journal of the ZMZ engine intermediate shaft with the bushing.
- 1 June 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (6) , 378-381
Evaluation of the Quality of the Process of Controlling the Process of the Front Journal of the Intermediate Shaft with a Caliper Gauge during Repairs of a ZMZ Engine
The procedure and sequence of quality assessment of processes of controlling carried out during machine repair are considered. The quality of the process of controlling the intermediate shaft diameter of a ZMZ engine using a caliper gauge was assessed. As a result of mathematical processing of the data, it was revealed that the process of control with a caliper gauge can be considered acceptable. Replacing the micrometer with a caliper gauge will not only improve the accuracy of control, but also significantly reduce the labor intensity of the work, which will ensure the quality of the assembly of the connection of the front journal of the ZMZ engine intermediate shaft with the bushing.
- 1 June 2026
- Published by Allerton Press in Russian Engineering Research
- Vol. 46 (6) , 743-746
Justification for the Use of Indicator Clamps with Digital Heads for Monitoring Valve Diameters of YaMZ Engines
The paper examines the nominal geometric parameters of YaMZ engine valves and their permissible deviations during defect identification and incoming qualit
- 1 June 2026
- Published by Allerton Press in Russian Engineering Research
- Vol. 46 (6) , 743-746
Justification for the Use of Indicator Clamps with Digital Heads for Monitoring Valve Diameters of YaMZ Engines
The paper examines the nominal geometric parameters of YaMZ engine valves and their permissible deviations during defect identification and incoming qualit
- 1 May 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (5) , 235-238
Metrological Support for Detecting Holes in Bushings for Camshaft Joints
The study examined the influence of bore gauge measurement errors on the formation of the number of incorrectly accepted and incorrectly rejected bushing holes under the camshaft journals cylinder blocks of YaMZ engines. The rationality of using the most accurate bore gauge from a range of universal instruments that satisfy the basic conditions for selecting measuring instruments has been scientifically substantiated and practically proven; otherwise, even if the selection condition is met, the percentage of losses increases in the form of sending such expensive parts as cylinder blocks to scrap.
- 1 May 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (5) , 235-238
Metrological Support for Detecting Holes in Bushings for Camshaft Joints
The study examined the influence of bore gauge measurement errors on the formation of the number of incorrectly accepted and incorrectly rejected bushing holes under the camshaft journals cylinder blocks of YaMZ engines. The rationality of using the most accurate bore gauge from a range of universal instruments that satisfy the basic conditions for selecting measuring instruments has been scientifically substantiated and practically proven; otherwise, even if the selection condition is met, the percentage of losses increases in the form of sending such expensive parts as cylinder blocks to scrap.
- 1 February 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (2) , 62-67
Ensuring the Quality of Repairs of Agricultural Machinery through the Use of Statistical Control Tools
- 1 February 2026
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 52 (2) , 62-67
Ensuring the Quality of Repairs of Agricultural Machinery through the Use of Statistical Control Tools
- 1 October 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (10) , 1354-1359
Application of Digital Technologies to Achieve Maximum Wear Margin for Clearance Fits
The article proposes a method for assembling clearance fits using digital technologies to ensure the maximum wear margin, on the example of the camshaft
- 1 October 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (10) , 1354-1359
Application of Digital Technologies to Achieve Maximum Wear Margin for Clearance Fits
The article proposes a method for assembling clearance fits using digital technologies to ensure the maximum wear margin, on the example of the camshaft
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 381-385
Study of Interference Dispersion Parameters in the Joint of the YAMZ Gearbox Shaft Output End and a Seal
The service life of the shaft–seal joint in agricultural machinery affects the overall operating life of the assembly. An analysis of factors influencing the durability of the shaft–seal joint revealed the need to investigate the quality of forming the initial interference-fit range in the joint and its compliance with the dimensional interchangeability parameters specified in the design documentation at the assembly design stage. The study aimed to evaluate the probabilistic characteristics of dimensional dispersion for the inner diameter of the seal and the outer diameter of the gearbox flange of the YaMZ-239 transmission. The study examined 100 flanges and 100 seals of type 1.2–100 × 125–12. Measurements of shaft-end diameters were made using an SRP 100-0.001 lever caliper. A DIP-6 instrument with an NIIK-890 system determined the inner diameter of the seals. An assessment of the dispersion parameters of the surface dimensions of the YaMZ-239 gearbox output shaft for the 100h10 seal seat showed that shaft manufacturing achieved process accuracy higher than required, with satisfactory process centering and exhibited a shift toward correctable defects. An investigation of the inner diameter of the seals showed good accuracy of the diameter-forming process, satisfactory process centering, and a slight shift toward non-correctable defects; however, no actual defects occurred. The analysis of interference dispersion showed that the probable percentage of defective joints, as a durability characteristic, equaled 0.01%. The results demonstrate that the manufacturing accuracy of the parts forming the flange–seal joint meets the specified requirements. Therefore, engineers should attribute emerging problems with lubricant leakage from seals to the wear-resistance parameters of these parts and to an analysis of wear in the influencing dimensions that form the dimensional chain, where misalignment deviation and shaft radial runout relative to the seal diameter act as the initial closing links.
- 1 September 2025
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 51 (9) , 381-385
Study of Interference Dispersion Parameters in the Joint of the YAMZ Gearbox Shaft Output End and a Seal
The service life of the shaft–seal joint in agricultural machinery affects the overall operating life of the assembly. An analysis of factors influencing the durability of the shaft–seal joint revealed the need to investigate the quality of forming the initial interference-fit range in the joint and its compliance with the dimensional interchangeability parameters specified in the design documentation at the assembly design stage. The study aimed to evaluate the probabilistic characteristics of dimensional dispersion for the inner diameter of the seal and the outer diameter of the gearbox flange of the YaMZ-239 transmission. The study examined 100 flanges and 100 seals of type 1.2–100 × 125–12. Measurements of shaft-end diameters were made using an SRP 100-0.001 lever caliper. A DIP-6 instrument with an NIIK-890 system determined the inner diameter of the seals. An assessment of the dispersion parameters of the surface dimensions of the YaMZ-239 gearbox output shaft for the 100h10 seal seat showed that shaft manufacturing achieved process accuracy higher than required, with satisfactory process centering and exhibited a shift toward correctable defects. An investigation of the inner diameter of the seals showed good accuracy of the diameter-forming process, satisfactory process centering, and a slight shift toward non-correctable defects; however, no actual defects occurred. The analysis of interference dispersion showed that the probable percentage of defective joints, as a durability characteristic, equaled 0.01%. The results demonstrate that the manufacturing accuracy of the parts forming the flange–seal joint meets the specified requirements. Therefore, engineers should attribute emerging problems with lubricant leakage from seals to the wear-resistance parameters of these parts and to an analysis of wear in the influencing dimensions that form the dimensional chain, where misalignment deviation and shaft radial runout relative to the seal diameter act as the initial closing links.
- 1 June 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (6) , 704-709
Calculation of Total Misalignment of a Gearbox Output Shaft Relative to the Seal
The article presents calculation of the dimensional chain for the shaft-seal coupling in which the master link contains misalignment and radial runout of t
- 1 June 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (6) , 704-709
Calculation of Total Misalignment of a Gearbox Output Shaft Relative to the Seal
The article presents calculation of the dimensional chain for the shaft-seal coupling in which the master link contains misalignment and radial runout of t
- 6 April 2025
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 54 (2) , 159-166
Calculation of Surface Roughness Parameters of Parts in Designing Accuracy Standards for Critical Joints
The dependences for calculating corrections for surface roughness crimpling of parts are proposed. The presented dependences allow one not only to determine the crimpling rate of the surface roughness at the time of joint formation, but also to limit the roughness rate to form the required contact area. Considering that Ra is standardized for critical surfaces of parts and Rz must be used to calculate the crimpling rate, the dependences for converting Ra to Rz are clarified. A comparative table is compiled confirming the correctness of the calculations in the range of Ra = 0.1–2.5 μm. Using the example of calculating and selecting a force fit, it is shown that different fits are obtained: ∅30H8/y8 with permissible values of surface roughness of the hole and shaft, and when using those specified in the drawing, ∅30H9/z9.
- 6 April 2025
- Published by Pleiades Publishing Ltd in Journal of Machinery Manufacture and Reliability
- Vol. 54 (2) , 159-166
Calculation of Surface Roughness Parameters of Parts in Designing Accuracy Standards for Critical Joints
The dependences for calculating corrections for surface roughness crimpling of parts are proposed. The presented dependences allow one not only to determine the crimpling rate of the surface roughness at the time of joint formation, but also to limit the roughness rate to form the required contact area. Considering that Ra is standardized for critical surfaces of parts and Rz must be used to calculate the crimpling rate, the dependences for converting Ra to Rz are clarified. A comparative table is compiled confirming the correctness of the calculations in the range of Ra = 0.1–2.5 μm. Using the example of calculating and selecting a force fit, it is shown that different fits are obtained: ∅30H8/y8 with permissible values of surface roughness of the hole and shaft, and when using those specified in the drawing, ∅30H9/z9.
- 1 March 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (3) , 284-288
Quality Index for a Vertical Honing Machine Used in Finishing Cylinder Liners
A comprehensive quality index is proposed for a vertical honing machine, taking account of the labor intensity, energy expenditure, and consumption of mate
- 1 March 2025
- Published by Allerton Press in Russian Engineering Research
- Vol. 45 (3) , 284-288
Quality Index for a Vertical Honing Machine Used in Finishing Cylinder Liners
A comprehensive quality index is proposed for a vertical honing machine, taking account of the labor intensity, energy expenditure, and consumption of mate
- 1 February 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (2) , 61-66
Application of Statistical Methods to Assess the Quality of the Machining Process
The finishing processes in mechanical engineering are aimed at creating ideal surfaces of parts satisfying specifications, in particular their dimensions, but these processes carried out on actual equipment are subject to deviations from specified values. Statistical methods of quality control and management are a diagnostic tool for analyzing the causes of variations. The diameters of 20 crankshaft main journals of the ZMZ engine were investigated after machining for the repair size. The quality of machining crankshaft journals was evaluated sequentially using quality tools such as the box-and-whisker diagram, Shewhart control charts, and histograms. It was found from the box-and-whisker diagram that after machining for the repair size all the journals had the diameter within the machining tolerance field, but at the same time there was a scatter between journal diameters of the same crankshaft. An analysis of the Shewhart control charts established that the scatter values within one subgroup (crankshaft) and between subgroups were caused by usual reasons, and this scatter pattern can be considered random. Hence, the process can be considered stable and controllable. The histogram helped to determine the probability of 1.95% for recoverable rejects after machining the engine journal for the repair size and the probability of zero for unrecoverable rejects. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. The index will decrease over time and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is recommended that the quality of machining crankshaft main journals for the repair size be checked regularly applying successively all three tools to identify the size variation and inconsistencies, which is particularly important for worn equipment.
- 1 February 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (2) , 61-66
Application of Statistical Methods to Assess the Quality of the Machining Process
The finishing processes in mechanical engineering are aimed at creating ideal surfaces of parts satisfying specifications, in particular their dimensions, but these processes carried out on actual equipment are subject to deviations from specified values. Statistical methods of quality control and management are a diagnostic tool for analyzing the causes of variations. The diameters of 20 crankshaft main journals of the ZMZ engine were investigated after machining for the repair size. The quality of machining crankshaft journals was evaluated sequentially using quality tools such as the box-and-whisker diagram, Shewhart control charts, and histograms. It was found from the box-and-whisker diagram that after machining for the repair size all the journals had the diameter within the machining tolerance field, but at the same time there was a scatter between journal diameters of the same crankshaft. An analysis of the Shewhart control charts established that the scatter values within one subgroup (crankshaft) and between subgroups were caused by usual reasons, and this scatter pattern can be considered random. Hence, the process can be considered stable and controllable. The histogram helped to determine the probability of 1.95% for recoverable rejects after machining the engine journal for the repair size and the probability of zero for unrecoverable rejects. The calculated reproducibility index of 0.93 indicates a significant wear of the equipment. The index will decrease over time and the risks of rejects will increase. The authors conclude that the quality of setting for machining crankshaft main bearing journals for the repair size is acceptable. It is recommended that the quality of machining crankshaft main journals for the repair size be checked regularly applying successively all three tools to identify the size variation and inconsistencies, which is particularly important for worn equipment.