SBS. A. Bogatyryov

S. A. Bogatyryov

*This is an algorithmically generated author record based on publicly available information.

S. A. Bogatyryov has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Methodological features of long-term forecasting of grain crop yield

    by Igor Leonidovich Vorotnikov, Alexander Vladiirovich Rozanov, Sergey Arkadievich Bogatyrev, Arkady Viktorovich Klyuchikov

    The article presents the results of analysis, modeling and formation of long-term forecasts of grain crop yields based on observations of the dynamics of time series of yields in the Russia and USA for a period of more than a century and a half. To increase the reliability and reliability of the forecasting results, it is proposed to use a generalized logistic function, which allows reducing the "error corridor" for large (ten or more years) forecast horizon. This is especially important in conditions of low predictability of climatic environmental factors, environmental crises, sanctions and the accompanying high volatility of yields over significant observation periods.

  • Open Access

    Justification of the Application of Resource-Saving Technology for the Restoration of Metal-Intensive Rear Semi-Axles of Trucks Using Hot Plastic Deformation

    by Konstantin P. Kolotyrin, Sergey A. Bogatyrev, Yuri Yu. Kostyukhin, Diana Yu. Savon, Alexey I. Shinkevich

    The article is devoted to the substantiation of technological foundations for the restoration of extremely worn-out, metal-consuming, and resource-consuming parts, in a method consisting of applying a compensating metal wear with subsequent plastic deformation. Currently, there are no technologies for their restoration in a repair facility that guarantee the resilience of the factory product. The proposed technological process of repair consists of butt welding onto the end of the spline semi-axle shank, compensating for the wear of the metal, the volume of which takes into account the losses resulting from the wear of the slots, as well as allowances for their machining. In the example of forging the axle shaft of a truck’s driving axle, the regularities of the plastic flow of metal during part deformation in the stamp are revealed. In the process of hot volumetric upsetting of long cylindrical parts with a variable diameter, it is important to know the possible directions of metal movements, as well as the energy-power characteristics of the process at various stages of forging. The evaluation criteria of the level of perfection of the technology were indicators of resource conservation and efficiency of the recovery route. The technological direction of the conducted research was analyzed, step by step, from the standpoint of saving repair materials and energy resources. The results of theoretical studies are crucial in the design of die tooling, for the manufacture of blanks, when restoring the rear axle shafts of trucks with pressure. Production tests carried out on the models, obtained as a result of mathematical processing of experimental data, confirmed the reliability of the experimental information. The introduction of the proposed set of repair equipment for the restoration of semi-axles will allow the formation of additional production in the region for the recycling of worn-out metal-intensive steel parts of agricultural machinery.


  • Open Access

    Improving the Efficiency of Grinding Sugar Beet in Centrifugal Beet Cutters

    by Feliks Ya. Rudik, Sergey А. Bogatyrev, Anatoliy P. Kovylin, Madina S. Tulieva

    Introduction. Grinding sugar beet should be carried out with minimal losses in centrifugal beet cutters with specially designed knives that provide frequent and constant chaotic longitudinal-lateral cutting of circular conductive beet knots. The objective of the work is to increase the reliability of the knives of centrifugal beet cutters by structural and technological strengthening in the process of their production and restoration. Materials and Methods. The state of the cutting edges of the knives was determined by using the micrometric measurement of the wear and deformation of the edges. Physical and mechanical indicators were analyzed based on the values of wear resistance, microhardness, and bending endurance. Results. The analyzes of the defective state of the knives of centrifugal beet cutters and theoretical studies of the grinding process have allowed formulating the factors affecting the permeability of the beet chips and the efficiency of their grinding with knives of a special diamond-shaped design. Experimental studies have made it possible to establish dynamically substantiated design parameters of an improved knurled knife. Discussion and Conclusion. The proposed measures ensured an increase in the durability of knives by 27-30%, the relative wear resistance of cutting edges by 20%, the limit of endurance of cutting edges for bending by 25% and a shift increase in the length of chips by 18-20% with an increase in its permeability by 16-18%.

  • Open Access

    Implementation of the new resource saving technology in manufacturing process

    by K. P. Kolotyrin, S. A. Bogatyryov, F. Ya. Rudik

    The authors of the article justify the expediency of applying resource saving in developing innovative technologies for hot rolling of boning knife blades from steel slabs. Such knives are widely used in meat processing industry. Metal consumption of the process was significantly reduced after changing the existing factory technology of making boning knives. The operation of cutting or grinding was replaced by hot rolling. The specific feature of the technology lies in minimizing the metal loss into shavings during the final processing of the steel slab by means of cutting. Reducing metal loss in making such steel parts and raising metal utilization rate are achieved by maximum possible approximation of forging configuration to the end product contour and preservation of the allowances regulated by the operational chart. The authors suggest optimal combinations of basic parameters of introduction of resource saving technology into production. To adduce an example the authors justify the possibility of shaping and simultaneous hardening of the knife blade during hot rolling between deforming rollers. Energy intensity of the technology suggested is lowered by means of reducing the time for further mechanic processing of the forging by cutting. Practical approbation of the introduced resource saving technology in repair production made it possible to raise the metal utilization rate to 95% and to reduce by 1.2 the production cost of a boning knife as the end product. When manufacturing the parts metal resources are saved due to the fact that irreversible loss of metal in the innovative technology of the boning knives’ production differs a lot from that in the traditional one. Technical and economic calculations adduced in the article show the effectiveness of the research and prove the profit of implementation of the new technology


  • Use of resource-saving technologies in fabrication and restoration of steel bushing-type components via hot plastic deformation

    by K. P. Kolotyrin, S. A. Bogatyrev, D. Yu. Savon, A. V. Aleksakhin

    The article substantiates the expediency of applying the foundations of resource saving in the development of innovative technologies for producing of machine billets hot die forging from worn machine components for the subsequent manufacture of them of new parts in the industrial conditions. Particular emphasis is placed on technologies that provide minimal impact to the environment based on the developed methods of metal processing. The optimal combinations of basic parameters of the process of introducing resource-saving technologies in the repair and maintenance operations are proposed. As an example, the article substantiates possibility of carrying out the process of shaping long tubular forgings from extremely worn thick-walled bushings.