Kiumars Khani Aminjan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Kiumars Khani Aminjan has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Zuorro
Department of Chemical Engineering, Materials, and Environment, Sapienza University, Via Eudossiana 18, 00184 Roma, Italy
3 shared publications - Davood Domairry Ganji
Department of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran
3 shared publications Samira Marami Milani
Department of Mechanical Engineering, Sou.C., Islamic Azad University, Sufian, Iran
3 shared publications- Maryam Ghodrat
School of Engineering and Technology, University of New South Wales Canberra, ACT, Australia
2 shared publications Milad Heidari
Mechanical Engineering Department, Global College of Engineering and Technology (GCET), Muscat, Sultanate of Oman
2 shared publications- Milad Heidari
Department of Mechanical Engineering Global College of Engineering and Technology Muscat Sultanate of Oman
2 shared publications
Latest Publications
- Open Access
- 12 February 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Experimental investigation on spray morphology in dual pitch spiral nozzle
This study investigates dual-spiral-pitch nozzles, which are essential for high-discharge applications like deluge fire suppression systems (5–4000 L/min). Such nozzles produce multi-sprays, which have received little attention in the past. In the present research, experiments quantified the relationship between inlet pressure (0.2–3.4 bar), mass flow rate, and spray characteristics. Results reveal three distinct spray morphologies linked to inlet pressure: a gradual mass flow rate increase across 0.2–1 bar inlet pressure, a dramatic surge exceeding 1000% between 1 and 3 bar, and an approach to hydraulic saturation (maximum achievable flow) at 3.4 bar, due to geometric constraints. In addition, the results indicated that at 0.2 bar inlet pressure, the nozzle produces single, coarse droplets. As pressure increases to 1.6 bar and above, the spray pattern evolves into two distinct, separate jets: an outer spray (Spray 1) and an inner spray (Spray 2). While increasing the inlet pressure from 1.6 to 3.4 bar causes the outer spray cone angle to expand significantly (from 64° to 121°), the inner spray cone angle remains remarkably stable at approximately 30°. These experimental findings can be used to rigorously verify the accuracy of the corresponding CFD simulations, providing necessary experimental validation for the models.
- 12 February 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessExperimental investigation on spray morphology in dual pitch spiral nozzle
This study investigates dual-spiral-pitch nozzles, which are essential for high-discharge applications like deluge fire suppression systems (5–4000 L/min). Such nozzles produce multi-sprays, which have received little attention in the past. In the present research, experiments quantified the relationship between inlet pressure (0.2–3.4 bar), mass flow rate, and spray characteristics. Results reveal three distinct spray morphologies linked to inlet pressure: a gradual mass flow rate increase across 0.2–1 bar inlet pressure, a dramatic surge exceeding 1000% between 1 and 3 bar, and an approach to hydraulic saturation (maximum achievable flow) at 3.4 bar, due to geometric constraints. In addition, the results indicated that at 0.2 bar inlet pressure, the nozzle produces single, coarse droplets. As pressure increases to 1.6 bar and above, the spray pattern evolves into two distinct, separate jets: an outer spray (Spray 1) and an inner spray (Spray 2). While increasing the inlet pressure from 1.6 to 3.4 bar causes the outer spray cone angle to expand significantly (from 64° to 121°), the inner spray cone angle remains remarkably stable at approximately 30°. These experimental findings can be used to rigorously verify the accuracy of the corresponding CFD simulations, providing necessary experimental validation for the models.
- Top Cited PapersOpen Access
- 1 January 2026
- Published by National Library of Serbia in Thermal Science
- Vol. 30 (1 Part B) , 629-641
Numerical investigation of interaction between internal mixing air and spray of three kinds of fluids
The widespread use of atomizers for fuel spraying in combustion chambers or water spraying for cooling purposes has made them attractive subjects for research. This study investigates the interaction of internal mixing high-velocity air-flow with the spray of three fluids in a pressure swirl atomizer. The research was conducted using the numerical solution method, supported by experimental data, which demonstrated good agreement between the simulation and experimental results. The findings revealed that adding 0.02 kg/s of high-velocity airflow at 300 K to the spray of three liquids, namely water, normal heptane, and kerosene, each at a mass-flow rate of 0.08 kg/s, reduced the fluid film thickness by 79.82%, 77.36%, and 76.87%, respectively. This reduction subsequently resulted in a significant decrease in the Sauter mean diameter by 96.99%, 96.12%, and 95.94%, respectively. Additionally, the results indicated that the addition of high-velocity airflow slightly increased the spray cone angle for kerosene and normal heptane, but caused the water spray to collapse and move out of its intended pattern. The study also found that high-velocity air-flow dramatically increased the turbulence kinetic energy for the spray of all three liquids, with a more pronounced effect observed in the water spray. These results can guide researchers in understanding the effects of high-velocity air-flow on spray dynamics and assist engineers in designing and manufacturing atomizers with optimal performance.
- 1 January 2026
- Published by National Library of Serbia in Thermal Science
- Vol. 30 (1 Part B) , 629-641
Top Cited PapersOpen AccessNumerical investigation of interaction between internal mixing air and spray of three kinds of fluids
The widespread use of atomizers for fuel spraying in combustion chambers or water spraying for cooling purposes has made them attractive subjects for research. This study investigates the interaction of internal mixing high-velocity air-flow with the spray of three fluids in a pressure swirl atomizer. The research was conducted using the numerical solution method, supported by experimental data, which demonstrated good agreement between the simulation and experimental results. The findings revealed that adding 0.02 kg/s of high-velocity airflow at 300 K to the spray of three liquids, namely water, normal heptane, and kerosene, each at a mass-flow rate of 0.08 kg/s, reduced the fluid film thickness by 79.82%, 77.36%, and 76.87%, respectively. This reduction subsequently resulted in a significant decrease in the Sauter mean diameter by 96.99%, 96.12%, and 95.94%, respectively. Additionally, the results indicated that the addition of high-velocity airflow slightly increased the spray cone angle for kerosene and normal heptane, but caused the water spray to collapse and move out of its intended pattern. The study also found that high-velocity air-flow dramatically increased the turbulence kinetic energy for the spray of all three liquids, with a more pronounced effect observed in the water spray. These results can guide researchers in understanding the effects of high-velocity air-flow on spray dynamics and assist engineers in designing and manufacturing atomizers with optimal performance.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Pressure swirl atomizer: Study on the effects of internal mixing air, its mass flow rate, and temperature on spray key characteristics
Although using high-velocity airflow is common in some types of atomizers, including airblast atomizers, researchers have not considered this idea in pressure swirl atomizers. The present study aimed to address this gap by experimental and numerical methods. First, the atomizer was designed and manufactured based on mass flow rate of 0.08 kg/s, the pressure difference of 3 bar, and the kerosene liquid and tested. Then, by simulation the effects of lack of high-velocity airflow, adding high-velocity airflow, increasing its mass flow rate and temperature were investigated. The results showed that by adding high-velocity airflow and increasing its mass flow rate from 0.02 to 0.03 kg/s, the Sauter mean diameter (SMD) extremely decreased from 4.0360 × 10−4 to 0.1638 × 10−4, then to 0.1315 × 10−4, but for the 0.03 kg/s, the spray pattern was not desirable. Although adding high-velocity airflow increased the spray cone angle from 74.5° to 80.3°, from 0.02 to 0.03 kg/s, it was decreased by 14.5°. Adding high-velocity airflow extremely reduced the discharge coefficient (Cd) by 94.65% but for 0.03 kg/s, the distribution of the spray was asymmetric, due to asymmetric distribution of velocity at the atomizer outlet. The study of the effects of high-velocity airflow temperature in 300, 350, and 375 K showed that although it caused an increase in the spray angle from 80.3° to 85.0° and then to 90.4°, due to the insensitivity of the velocity and kinetic energy of turbulence to temperature SMD and Cd, both decreased only approximately 0.49%.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Pressure swirl atomizer: Study on the effects of internal mixing air, its mass flow rate, and temperature on spray key characteristics
Although using high-velocity airflow is common in some types of atomizers, including airblast atomizers, researchers have not considered this idea in pressure swirl atomizers. The present study aimed to address this gap by experimental and numerical methods. First, the atomizer was designed and manufactured based on mass flow rate of 0.08 kg/s, the pressure difference of 3 bar, and the kerosene liquid and tested. Then, by simulation the effects of lack of high-velocity airflow, adding high-velocity airflow, increasing its mass flow rate and temperature were investigated. The results showed that by adding high-velocity airflow and increasing its mass flow rate from 0.02 to 0.03 kg/s, the Sauter mean diameter (SMD) extremely decreased from 4.0360 × 10−4 to 0.1638 × 10−4, then to 0.1315 × 10−4, but for the 0.03 kg/s, the spray pattern was not desirable. Although adding high-velocity airflow increased the spray cone angle from 74.5° to 80.3°, from 0.02 to 0.03 kg/s, it was decreased by 14.5°. Adding high-velocity airflow extremely reduced the discharge coefficient (Cd) by 94.65% but for 0.03 kg/s, the distribution of the spray was asymmetric, due to asymmetric distribution of velocity at the atomizer outlet. The study of the effects of high-velocity airflow temperature in 300, 350, and 375 K showed that although it caused an increase in the spray angle from 80.3° to 85.0° and then to 90.4°, due to the insensitivity of the velocity and kinetic energy of turbulence to temperature SMD and Cd, both decreased only approximately 0.49%.
- 8 January 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (3) , 2329-2348
Experimental and Numerical Study on Inlet Pressure and Reynolds Number in Tangential Input Pressure-Swirl Atomizer
- 8 January 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (3) , 2329-2348
Experimental and Numerical Study on Inlet Pressure and Reynolds Number in Tangential Input Pressure-Swirl Atomizer
- 28 August 2024
- Published by Springer Nature in Experimental and Computational Multiphase Flow
- Vol. 6 (4) , 428-445
Numerical investigation of the impact of fuel temperature on spray characteristics in a pressure-swirl atomizer with spiral path
- 28 August 2024
- Published by Springer Nature in Experimental and Computational Multiphase Flow
- Vol. 6 (4) , 428-445
Numerical investigation of the impact of fuel temperature on spray characteristics in a pressure-swirl atomizer with spiral path
- Open Access
- 1 July 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (7)
Study on duplex air-blast atomizers spray in the engine real operation conditions
Air-blast atomizers are widely used in passenger aircraft engines. In these atomizers, high-speed airflow is used for improved fuel atomization, and as a result, better combustion. The key purpose of this research is to investigate the duplex air-blast atomizers according to the engine data in the real operational conditions with the help of experimental method and numerical solution. When analyzing the variations in fuel sprays under different application conditions, it is important to consider not just one but multiple parameters such as fuel mass rate, air mass rate, and combustion chamber pressure. However, analyzing the individual effects of these parameters can be challenging as they change simultaneously. To address this, a dimensionless number namely K was defined, which takes into account the combined effect of fuel mass rate, air mass rate, and combustion chamber pressure. The results showed that when K decreased by 31.25%, the spray angle of nozzle 1 and nozzle 2 increased by 10.09% and 48.15%, respectively, while the average droplet diameter caused by primary breakup for nozzle 1 and nozzle 2 decreased by 76.29% and 71.57%, respectively. The secondary breakup was somewhat similar, and for nozzle 1 and nozzle 2, the average droplet diameter decreased by 76.5% and 71.88%, respectively. It is worth noting that the average error for spray cone angle in the simulation compared to the experimental results was 6.47%. The results of this research, in addition to causing a better understanding of the atomization processes in air-blast atomizers, can be useful for aerospace engineers.
- 1 July 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (7)
Open AccessStudy on duplex air-blast atomizers spray in the engine real operation conditions
Air-blast atomizers are widely used in passenger aircraft engines. In these atomizers, high-speed airflow is used for improved fuel atomization, and as a result, better combustion. The key purpose of this research is to investigate the duplex air-blast atomizers according to the engine data in the real operational conditions with the help of experimental method and numerical solution. When analyzing the variations in fuel sprays under different application conditions, it is important to consider not just one but multiple parameters such as fuel mass rate, air mass rate, and combustion chamber pressure. However, analyzing the individual effects of these parameters can be challenging as they change simultaneously. To address this, a dimensionless number namely K was defined, which takes into account the combined effect of fuel mass rate, air mass rate, and combustion chamber pressure. The results showed that when K decreased by 31.25%, the spray angle of nozzle 1 and nozzle 2 increased by 10.09% and 48.15%, respectively, while the average droplet diameter caused by primary breakup for nozzle 1 and nozzle 2 decreased by 76.29% and 71.57%, respectively. The secondary breakup was somewhat similar, and for nozzle 1 and nozzle 2, the average droplet diameter decreased by 76.5% and 71.88%, respectively. It is worth noting that the average error for spray cone angle in the simulation compared to the experimental results was 6.47%. The results of this research, in addition to causing a better understanding of the atomization processes in air-blast atomizers, can be useful for aerospace engineers.
- 5 February 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (1) , 208-214
Estimating Spray Characteristics of the Air-Blast atomizer of a Typical Jet Engine using Definition of the New Non-dimensional Number K: Numerical and Experimental Study
In this paper, by using a numerical solution and experiment investigation, a non-dimensional number is introduced to estimate the characteristics of a real engine airblast atomizer spray. This type of atomizers is usually used in airplain engines. Th...
- 5 February 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (1) , 208-214
Estimating Spray Characteristics of the Air-Blast atomizer of a Typical Jet Engine using Definition of the New Non-dimensional Number K: Numerical and Experimental Study
In this paper, by using a numerical solution and experiment investigation, a non-dimensional number is introduced to estimate the characteristics of a real engine airblast atomizer spray. This type of atomizers is usually used in airplain engines. Th...
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 093305
Study of pressure-swirl atomizer with spiral path at design point and outside of design point
Studies on pressure-swirl atomizers have mainly focused on pressure-swirl atomizers with tangential input while there are limited studies on pressure-swirl atomizers with a spiral path. This study applies experimental and computational methods to provide a better understanding of flow development in this type of atomizer at the design point and outside the design point. Experimental results showed that as the pressure increases, the spray cone angle increases. This increase initially occurs with a higher slope and then the slope is toned down. While the drainage coefficient remains constant, the droplet diameter decreases as the pressure increases. It is observed that similar to the pressure-swirl atomizer with tangential input, the pressure-swirl atomizer with a spiral path has a conical hollow spray. At the constant mass flow rate, as the spiral path cross-section, the length of the swirl chamber and orifice diameter increase, the fluid film thickness and average diameter of droplets increase while the spray cone angle reduces. Further, increasing the number of spiral paths causes a wider spray cone angle, higher discharge coefficient, larger fluid film thickness, and larger droplet diameter. The results also showed that increasing the length of the orifice marginally affected the properties of the spray while significantly reducing the spray cone angle. It is important to note that the numerical results are in good agreement with the experimental data.
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 093305
Study of pressure-swirl atomizer with spiral path at design point and outside of design point
Studies on pressure-swirl atomizers have mainly focused on pressure-swirl atomizers with tangential input while there are limited studies on pressure-swirl atomizers with a spiral path. This study applies experimental and computational methods to provide a better understanding of flow development in this type of atomizer at the design point and outside the design point. Experimental results showed that as the pressure increases, the spray cone angle increases. This increase initially occurs with a higher slope and then the slope is toned down. While the drainage coefficient remains constant, the droplet diameter decreases as the pressure increases. It is observed that similar to the pressure-swirl atomizer with tangential input, the pressure-swirl atomizer with a spiral path has a conical hollow spray. At the constant mass flow rate, as the spiral path cross-section, the length of the swirl chamber and orifice diameter increase, the fluid film thickness and average diameter of droplets increase while the spray cone angle reduces. Further, increasing the number of spiral paths causes a wider spray cone angle, higher discharge coefficient, larger fluid film thickness, and larger droplet diameter. The results also showed that increasing the length of the orifice marginally affected the properties of the spray while significantly reducing the spray cone angle. It is important to note that the numerical results are in good agreement with the experimental data.
- 1 December 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (12) , 127113
Study of pressure swirl atomizer with tangential input at design point and outside of design point
Pressure swirl atomizers with tangential inputs are widely used in various industries, including power generation and gas turbines. For example, in combustion chambers with increasing time, a lot of factors, such as sediments and corrosions, cause their dimensions to reduce, and therefore, the working condition of these chambers moves outside of the design point. The main purpose of this work is to study the properties of spray at the design point and outside of the design point. To satisfy this objective, design and fabrication of an injector were done first based on some physical parameters, such as pressure difference, spray cone angle, flow rate, fluid type, and so on, and then, it was tested experimentally. Afterward, the effects of the main parameters at the design point and outside of the design point were studied numerically. The results showed a 50% increase in the number of tangential inputs from the design point lowers the pressure difference and spray cone angle by 63.72% and 10.53%, respectively. The increment of the swirl chamber length to 17% can reduce the respective pressure difference and spray cone angle up to 34.2% and 4.5%, respectively. This study also demonstrates that an increase in the length of the orifice lessens the total velocity and pressure as well. A reduction of 22.73% of the outlet nozzle diameter raises the average droplet diameter and flow number to 12.98%, and 11.8%, respectively. Finally, for the requirement of spray properties in a practical situation, the present study can be adopted to predict them accurately.
- 1 December 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (12) , 127113
Study of pressure swirl atomizer with tangential input at design point and outside of design point
Pressure swirl atomizers with tangential inputs are widely used in various industries, including power generation and gas turbines. For example, in combustion chambers with increasing time, a lot of factors, such as sediments and corrosions, cause their dimensions to reduce, and therefore, the working condition of these chambers moves outside of the design point. The main purpose of this work is to study the properties of spray at the design point and outside of the design point. To satisfy this objective, design and fabrication of an injector were done first based on some physical parameters, such as pressure difference, spray cone angle, flow rate, fluid type, and so on, and then, it was tested experimentally. Afterward, the effects of the main parameters at the design point and outside of the design point were studied numerically. The results showed a 50% increase in the number of tangential inputs from the design point lowers the pressure difference and spray cone angle by 63.72% and 10.53%, respectively. The increment of the swirl chamber length to 17% can reduce the respective pressure difference and spray cone angle up to 34.2% and 4.5%, respectively. This study also demonstrates that an increase in the length of the orifice lessens the total velocity and pressure as well. A reduction of 22.73% of the outlet nozzle diameter raises the average droplet diameter and flow number to 12.98%, and 11.8%, respectively. Finally, for the requirement of spray properties in a practical situation, the present study can be adopted to predict them accurately.