Motohiro Ohno
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Motohiro Ohno has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Tetsuya Ishida
The University of Tokyo
4 shared publications Tetsuya Ishida
3 shared publicationsKoichi Imagawa
2 shared publications- Ryota Kurihara
The University of Tokyo
2 shared publications - Jean-François Caron
Navier, ENPC, Institut Polytechnique de Paris, Univ. Gustave Eiffel, CNRS
1 shared publication - Ji Woon Park
Department of Civil and Environmental Engineering, Yonsei University, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 14 May 2026
- Published by Elsevier in Structures
- Vol. 89
Structural response of thermoplastic basalt FRP-RC and BFRTP-steel hybrid-RC columns at full scale under cyclic lateral loading
- 14 May 2026
- Published by Elsevier in Structures
- Vol. 89
Open AccessStructural response of thermoplastic basalt FRP-RC and BFRTP-steel hybrid-RC columns at full scale under cyclic lateral loading
- Open Access
- 21 April 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 526
Micromechanical design strategy for enhancing tensile ductility of strain-hardening basalt fiber reinforced cementitious composites
- 21 April 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 526
Open AccessMicromechanical design strategy for enhancing tensile ductility of strain-hardening basalt fiber reinforced cementitious composites
- 2 September 2025
- Published by Springer Nature
- p. 240-247
Experimental and FE Analytical Study on Flexural Load-Bearing Mechanism of Hybrid Basalt FRTP-Steel-RC Beams
- 2 September 2025
- Published by Springer Nature
- p. 240-247
Experimental and FE Analytical Study on Flexural Load-Bearing Mechanism of Hybrid Basalt FRTP-Steel-RC Beams
- Open Access
- 16 June 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 163
Cement-based mechanical metamaterials with spiral resonators for vibration control
- 16 June 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 163
Open AccessCement-based mechanical metamaterials with spiral resonators for vibration control
- Open Access
- 7 April 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 161
Fully coupled physicochemical-mechanical modeling of sulfate attack-induced expansion in cement-based materials
- 7 April 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 161
Open AccessFully coupled physicochemical-mechanical modeling of sulfate attack-induced expansion in cement-based materials
- Open Access
- 19 April 2023
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 21 (4) , 271-283
A Micromechanics-based Study on Cracking Characteristics of Engineered Geopolymer Composite
This study aims at experimentally and analytically characterizing cracking characteristics of Engineered Geopolymer Composites (EGCs) and at identifying optimal combinations of micromechanical parameters for enhancing the composite tensile performance. Fly ash-based EGCs with different volume fractions of polyvinyl alcohol fibers are investigated. The number of cracks and residual crack widths are measured for EGC specimens uniaxially loaded to 1% and 2% tensile strain. The observed crack patterns are analyzed by a micromechanics-based model that relates matrix, fiber, and interface properties to the macroscopic composite behavior. The experimental results demonstrate the lognormal distributions of crack widths and more tightly controlled cracking compared to Engineered Cementitious Composites. The simulated fiber bridging stress-crack opening relationship (σ-δ relationship) suggests that relatively high chemical bond and low frictional bond lead to the tight crack width. The simulation results also suggest that the first-cracking strength and the subsequent micro-cracking stress during the hardening stage should be below the analytical σ-δ curve peak. Higher chemical bond is beneficial for meeting these conditions, but if it is too high, fiber rupture dominates over pull-out, which lowers the complementary energy. Lower frictional bond or slip-hardening coefficient can suppress the fiber rupture tendency.
- 19 April 2023
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 21 (4) , 271-283
Open AccessA Micromechanics-based Study on Cracking Characteristics of Engineered Geopolymer Composite
This study aims at experimentally and analytically characterizing cracking characteristics of Engineered Geopolymer Composites (EGCs) and at identifying optimal combinations of micromechanical parameters for enhancing the composite tensile performance. Fly ash-based EGCs with different volume fractions of polyvinyl alcohol fibers are investigated. The number of cracks and residual crack widths are measured for EGC specimens uniaxially loaded to 1% and 2% tensile strain. The observed crack patterns are analyzed by a micromechanics-based model that relates matrix, fiber, and interface properties to the macroscopic composite behavior. The experimental results demonstrate the lognormal distributions of crack widths and more tightly controlled cracking compared to Engineered Cementitious Composites. The simulated fiber bridging stress-crack opening relationship (σ-δ relationship) suggests that relatively high chemical bond and low frictional bond lead to the tight crack width. The simulation results also suggest that the first-cracking strength and the subsequent micro-cracking stress during the hardening stage should be below the analytical σ-δ curve peak. Higher chemical bond is beneficial for meeting these conditions, but if it is too high, fiber rupture dominates over pull-out, which lowers the complementary energy. Lower frictional bond or slip-hardening coefficient can suppress the fiber rupture tendency.
- 21 December 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 65
Simulation and learning-driven design for architected cement-based materials
- 21 December 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 65
Simulation and learning-driven design for architected cement-based materials
- 1 April 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 47
Multiscale modeling of steel corrosion in concrete based on micropore connectivity
- 1 April 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 47
Multiscale modeling of steel corrosion in concrete based on micropore connectivity
- 23 December 2020
- Published by Springer Nature
- p. 1891-1901
Quantitative Evaluation of Buildability in 3D Concrete Printing Based on Shear Vane Test
- 23 December 2020
- Published by Springer Nature
- p. 1891-1901
Quantitative Evaluation of Buildability in 3D Concrete Printing Based on Shear Vane Test