DXDanmei Xie

Danmei Xie

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Danmei Xie has a total of 43 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Low-Grade Flow Energy Harvesting by Low-Mass-Ratio Oscillating Bent Plate

    by Wei Jiang, Fan Wu, Ziyue Mei, Rui Shi, Danmei Xie

    Low-grade renewable energy possesses large reserves and a wide distribution in the environment, but it is far from fully exploited due to the high cost–income ratio when using traditional convertors. A fluid-induced-vibration-based flow energy convertor with a low-cost bent plate as an oscillator is proposed to achieve better energy converting performance for low-grade flow energy conversion. The energy extraction performance and dynamic response of the bent plate are assessed numerically. The results demonstrate that the prescribed single-DOF (degree of freedom) bent plate can reach the maximum efficiency of 29.6% and power coefficient of 2.36 at the relative plunging amplitude of 3.5, while the double-DOF bent plate achieves a maximum efficiency of 37.3% and power coefficient of 1.42 at a smaller amplitude of 1.4. It is discovered that the adoption of pitching motion can help to control the variation pattern of the effective AOA (angle of attack), while the camber of the bent plate also regulates the effective AOA from the geometrical respect. The FIV-based single-DOF convertor can achieve an energy converting efficiency of 29.3% and approach the ideal sinusoidal motion trajectory closely, indicating that the optimal active motion mode can be realized by the passive motion mode with the appropriate choice of the dynamic parameters.


  • Open Access

    Heat transfer enhancement by sinusoidal wavy tape insert in two-pass ribbed channels

    by Wei Jiang, Ziyue Mei, Fan Wu, Youmin Hou, Danmei Xie

    The turbine inlet temperature is one of the most critical parameter that determines the thermal efficiency and thrust-weight ratio of the gas turbine. However, the higher gas turbine inlet temperature significantly increases the thermal stress on the blade, which necessitates effective cooling strategy to reduce the blade temperature. In this study, a united blade cooling strategy was developed by adopting a two-pass ribbed cooling channel with wavy tape for the reason that ribs are near-wall turbulence promoters while the wavy tape is core-region promoter with relatively lower pressure-drop penalty. Ribs and wavy tape may complement each other in the cooling channel. The synergistic effect of the combined near-wall and core-region heat transfer promoter was numerically studied for Reynolds numbers from 6000 to 30000. Two key geometrical factors, namely rib to wave crest phase shift and relative wave amplitude, have significant effect on the thermal performance. The results demonstrate that wavy tape with different phase shift configurations can eliminate the lower heat transfer areas and produce more uniform heat transfer. The 0? phase shift achieved best overall thermal performance, which provided 1.07-1.08 times the flat tape heat transfer enhancement with 1.09-1.11 times the pressure drop penalty. The better heat performance is due to the secondary flow induced by wavy tape, which enhances the fluid mixing between near-wall and core-region.


  • Open Access

    Numerical Calculation of Seal Clearance Change in Installation Process of a 1000MW Nuclear Steam Turbine HIP Casing

    by Daohui Ji, Ziyue Mei, Wei Jiang, Caiyan Xiang, Danmei Xie, Yanan Yue

    During the installation process, most of 1000MW-class nuclear power steam turbines will undergo certain deformations due to their own big size and heavy weight, which will change seal clearances of steam passage. If the clearance is too big, it will lead leakage loss and affect steam turbine’s efficiency. If the clearance is too small, it may cause the rubbing fault between moving

  • High thermal conductivity of free-standing skeleton in graphene foam

    by Jianshu Gao, Danmei Xie, Xinwei Wang, Xin Zhang, Yanan Yue

    Due to the high-porosity structure, the low thermal transport property of graphene foam (GF) is expected. However, the interconnected skeleton can still act as excellent thermal conductor branches if phonon scattering is not severely affected in the structure of graphene flakes. Such a property has not been validated experimentally due to the difficulty in sample manipulation and the fragility of the structure. In this work, we report the characterization results of thermal properties of the free-standing skeleton in GF. Three individual skeleton samples from one GF piece are prepared under the same condition. The thermal diffusivity of GF skeletons is characterized in the range of 3.26–3.48 × 10−4 m2/s, and the thermal conductivity is determined to be 520–555 W/(m K), which is two orders of magnitude larger than the value of bulk GF. These high thermal conductivity values originate from the intrinsic thermal property of graphene, while the contact interfaces, wrinkled structures, and defects induced in the synthesis process do not affect the phonon transport property significantly, which proves that the three-dimensional hierarchical graphene structure can still be implemented in energy-intensive applications.


  • Open Access

    The Effect of Suction Side Tubercles on Torque Output of a Steam Turbine Low-Pressure Last Stage Blade

    by Jing Zhang, Fan Wu, Chun Wang, Ziyue Mei, An Han, Danmei Xie

    Flow separation and different kinds of stall flows occur under low load conditions for steam turbine last stage blades. In order to delay the flow separation and increase turbine power production, we applied suction side tubercles on steam turbine low-pressure last stage blades in the present study. The amplitude, wavelength, position, and thickness were considered as our design variables. We used the orthogonal test method (OTM) to generate modified blades with different tubercle variables that were then numerically simulated by a three-dimensional computational fluid dynamics (CFD) analysis. The blade axial torque of the nine modified tests was compared with the original blade. The results showed that the application of bionic tubercles on the suction side of the steam turbine blade is a promising solution to improve the blade axial torque for all modified tests with a maximum increase of 33.32% due to the turbulent vortices generated by bionic tubercles.


  • Open Access

    Conjugate Heat Transfer Investigation on Swirl-Film Cooling at the Leading Edge of a Gas Turbine Vane

    by Haifen Du, Ziyue Mei, Jiayao Zou, Wei Jiang, Danmei Xie

    Numerical calculation of conjugate heat transfer was carried out to study the effect of combined film and swirl cooling at the leading edge of a gas turbine vane with a cooling chamber inside. Two cooling chambers (C1 and C2 cases) were specially designed to generate swirl in the chamber, which could enhance overall cooling effectiveness at the leading edge. A simple cooling chamber (C0 case) was designed as a baseline. The effects of different cooling chambers were studied. Compared with the C0 case, the cooling chamber in the C1 case consists of a front cavity and a back cavity and two cavities are connected by a passage on the pressure side to improve the overall cooling effectiveness of the vane. The area-averaged overall cooling effectiveness of the leading edge ( ϕ ¯ ¯ ) was improved by approximately 57%. Based on the C1 case, the passage along the vane was divided into nine segments in the C2 case to enhance the cooling effectiveness at the leading edge, and ϕ ¯ ¯ was enhanced by 75% compared with that in the C0 case. Additionally, the cooling efficiency on the pressure side was improved significantly by using swirl-cooling chambers. Pressure loss in the C2 and C1 cases was larger than that in the C0 case.


  • Overall Cooling Effectiveness on a Gas Turbine Vane With Swirl-Film Cooling

    by Haifen Du, Danmei Xie, Wei Chen, Ziyue Mei, Jing Zhang

    Numerical calculation of conjugate heat transfer is carried out to study the effect of combined film and swirl cooling at the leading edge of a gas turbine vane with a a cooling chamber inside, in which 3-D steady RANS approach with the k-ω SST turbulence model is used. Two different kinds of coolant chamber configuration (C1 and C2) are selected. In C2, the cooling chamber is composed of a front cavity and a back cavity, and the two cavities are connected by a passage which is divided into 16 segments. The comparative investigations between C1 and C2 cases have been carried out to study the effect of different cooling chambers at M = 0.25, 0.5, 1 and 2. For two cases, overall cooling effectiveness increases with M increasing. In C1 case, with increasing M, differences of mass flow through film holes rows will decrease. The variation of mass flow from holes changes by less than 26.7% at M = 2. However, in C2 case, mass flow through S1 and S2 is significantly larger than that through other film holes rows. Area-averaged overall effectiveness in C2 is larger by 2.5% at M = 0.25 compared to C1 case.


  • Numerical Study on Heat Transfer Enhancement of Swirl Chamber on Gas Turbine Blade

    by Haifen Du, Daimei Xie, Wei Jiang, Tong Chen, Jianshu Gao

    The optimization of turbine cooling design has become a new research field of gas turbine. The swirl chamber is a prospect cooling concept. In this paper, the numerical simulation of the swirl chamber is carried out by FLUENT. The influence of inlet size parameters, temperature ratio and inlet Reynolds number on the enhanced heat transfer of swirl chamber is studied. The results show that, in the range of the studied condition, Nusselt number decreases with the height, the width, the ratio of width to height and Reynolds number. It also shows that comprehensive heat transfer effect is best at d=20 mm and enhances observably with the enlargement of width, width height ratio, and Reynolds number. Friction factor increases with height, width, temperature ratio and Reynolds number decreases. It is increased by increasing width height ratio. Nusselt number and comprehensive heat transfer effect decrease a little with aggrandizement of temperature ratio.


  • Analysis of Influence of Fast-Cut-Back Test on 1000-MW Steam Turbine Safety

    by Dan-Mei Xie, Yi Yang, Chang Chen, Peng-Fei Hu, Jie Guo, Wei Jiang

    The capacity of the power grid in China is increasing rapidly. Because of the reliability of the multi-infeed direct current (DC) system in the grid, power-system damping is relatively weak. Realizing isolated island operation of thermal power units with fast-cut-back (FCB) ability is considered to be the best solution for the quick restoration of the power grid. Taking a 1000-MW ultra-supercritical (USC) unit as an example, based on the field-test data of load rejection, this paper studies the dynamic responses of the turbine side during the FCB process. First, the maximum speed increase of the rotor during the FCB process with different loads is simulated using software. Second, the water levels of the deaerator and condenser during the FCB process are predicted with different loads using the same method. Third, the highest exhaust steam temperature of the high-pressure (HP) cylinder during the FCB process is calculated and predicted with different loads using finit-element modeling (FEM). Fourth, these key parameters are compared with the field FCB test data, and the comparison shows that the predicted results agree with the field-test data very well. Finally, the influence of the FCB test on the safety and life loss of the turbine side is analyzed.