Shu-Lin Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shu-Lin Ren has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Zhigang Tao
School of Mechanics and Civil Engineering, China University of Mining and Technology, Beijing, China
5 shared publications - Hao-Tian Xu
State Key Laboratory for Geomechanics & Deep Underground Engineering, Beijing, China
4 shared publications - Manchao He
China University of Mining and Technology-Beijing
4 shared publications - Qian Yin
State Key Laboratory of Intelligent Construction and Healthy Operation and Maintenance of Deep Underground Engineering China University of Mining and Technology Xuzhou China
4 shared publications - Senlin Luo
Department of Geological and Hydraulic Engineering College of Civil Engineering Tongji University Shanghai China
3 shared publications Zhigang Tao
3 shared publications
Latest Publications
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Development of a new shear strength criterion for rock joints based on three-dimensional directional roughness parameters
The major aim of the current research is to accurately predict the shear strength of rough joints to properly evaluate the stability of mining structures built on jointed foundations. The roughness of the joint surface is direction-dependent and is a significant factor influencing the peak shear strength of rough joints. Quantitatively evaluating the three-dimensional (3D) roughness of rock joints is a challenge. This study employed a non-contact 3D laser scanning technology to measure the rough joint morphology and adopted the high-precision 3D printing technique to manufacture the photosensitive resin molds. A batch of joints with the same morphology was replicated, and the joint shear tests were performed under five kinds of load conditions. Two new 3D directional roughness metrics were developed to characterize the morphology of rock joints, i.e., the 3D maximum contact area ratio (Am) and the root mean square of the apparent dip that faces the shear direction (θ*2). These two directional roughness parameters have clear physical significance and can capture the anisotropy of surface roughness. A new peak shear strength criterion incorporating the proposed 3D directional roughness parameters was developed. In addition, comparisons were made between the new criterion and the existing criteria in the literature. It was found that the joint roughness coefficient–joint compressive strength model underestimates the shear strength of rock joints. Compared with the 3D models in the literature, the new model has a better agreement with test results. In addition, the anisotropy of shear strength was also investigated. The anisotropy of joint shear strength decreases with increasing applied normal stress.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Development of a new shear strength criterion for rock joints based on three-dimensional directional roughness parameters
The major aim of the current research is to accurately predict the shear strength of rough joints to properly evaluate the stability of mining structures built on jointed foundations. The roughness of the joint surface is direction-dependent and is a significant factor influencing the peak shear strength of rough joints. Quantitatively evaluating the three-dimensional (3D) roughness of rock joints is a challenge. This study employed a non-contact 3D laser scanning technology to measure the rough joint morphology and adopted the high-precision 3D printing technique to manufacture the photosensitive resin molds. A batch of joints with the same morphology was replicated, and the joint shear tests were performed under five kinds of load conditions. Two new 3D directional roughness metrics were developed to characterize the morphology of rock joints, i.e., the 3D maximum contact area ratio (Am) and the root mean square of the apparent dip that faces the shear direction (θ*2). These two directional roughness parameters have clear physical significance and can capture the anisotropy of surface roughness. A new peak shear strength criterion incorporating the proposed 3D directional roughness parameters was developed. In addition, comparisons were made between the new criterion and the existing criteria in the literature. It was found that the joint roughness coefficient–joint compressive strength model underestimates the shear strength of rock joints. Compared with the 3D models in the literature, the new model has a better agreement with test results. In addition, the anisotropy of shear strength was also investigated. The anisotropy of joint shear strength decreases with increasing applied normal stress.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Shear performance of rock joints bolted by a novel high-strength and high-ductility anchor steel under constant normal stiffness
Negative Poisson's ratio (NPR) steel is an independently developed, novel high-strength and high-ductility anchor steel. This study conducted shear tests on joints bolted by NPR steel (hereinafter referred to as “NPR steel bolted joints”) under constant normal stiffness (CNS) and introduces test variables, such as constant normal load (CNL), Q235 steel anchorage, and joint surface roughness for a comparative analysis of the anchorage shear mechanical properties and shear resistance mechanism of NPR steel. Based on the results, bolt anchorage significantly improves the shear strength of jointed rock mass and significantly constrains the dilatancy of rough joint surfaces in the shear process. The anchorage shear strength in the plastic stage remains unchanged under CNL, while the curve presented plastic hardening characteristics under CNS. NPR steel is significantly superior to Q235 steel in improving the strength and ductility of, and imposing normal constraints on jointed rock mass. The parameter of plastic hardening stiffness is defined to reflect the hardening effect of anchor bolts on jointed rock mass. The results indicated that with the increase in normal stiffness, the shear hardening effect of anchor bolts on jointed rock mass becomes increasingly apparent. High-strength anchor bolts produce plastic hinges with a larger distance between them so that they will have a greater capacity to withstand shear deformation in the plastic stage, while high-ductility anchor bolts allow them to resist larger shear deformation without fracture in the plastic stage of anchorage shear. As a novel high-strength and high-ductility anchor steel, NPR anchor steel can meet the control requirements for large shear deformation resistance and energy absorption in deep surrounding rock support engineering, presenting a promising application prospect.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Shear performance of rock joints bolted by a novel high-strength and high-ductility anchor steel under constant normal stiffness
Negative Poisson's ratio (NPR) steel is an independently developed, novel high-strength and high-ductility anchor steel. This study conducted shear tests on joints bolted by NPR steel (hereinafter referred to as “NPR steel bolted joints”) under constant normal stiffness (CNS) and introduces test variables, such as constant normal load (CNL), Q235 steel anchorage, and joint surface roughness for a comparative analysis of the anchorage shear mechanical properties and shear resistance mechanism of NPR steel. Based on the results, bolt anchorage significantly improves the shear strength of jointed rock mass and significantly constrains the dilatancy of rough joint surfaces in the shear process. The anchorage shear strength in the plastic stage remains unchanged under CNL, while the curve presented plastic hardening characteristics under CNS. NPR steel is significantly superior to Q235 steel in improving the strength and ductility of, and imposing normal constraints on jointed rock mass. The parameter of plastic hardening stiffness is defined to reflect the hardening effect of anchor bolts on jointed rock mass. The results indicated that with the increase in normal stiffness, the shear hardening effect of anchor bolts on jointed rock mass becomes increasingly apparent. High-strength anchor bolts produce plastic hinges with a larger distance between them so that they will have a greater capacity to withstand shear deformation in the plastic stage, while high-ductility anchor bolts allow them to resist larger shear deformation without fracture in the plastic stage of anchorage shear. As a novel high-strength and high-ductility anchor steel, NPR anchor steel can meet the control requirements for large shear deformation resistance and energy absorption in deep surrounding rock support engineering, presenting a promising application prospect.
- 1 May 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (5)
A novel fracture dissolution model considering the nonlinear flow capacity of rough fractures
Existing research rarely considers the effects of rough fracture seepage on the progressive evolution processes of each physical field, and it primarily focuses on two-dimensional conditions. This study proposes a method to couple the Forchheimer equation with the Reynolds equation with time-varying apertures. The nonlinear flow of three-dimensional fractures under dissolution conditions is achieved. Then, the modified Reynolds equation under steady-state conditions is compared to the flow field governed by the Reynolds equation, and the validity of the modified Reynolds equation after coupling with the Forchheimer equation is verified. The results indicated that the maximum velocity of the flow field controlled by the modified Reynolds equation is slightly lower than that of the flow field controlled by the Reynolds equation, although the overall distribution trends are consistent. Under the control of the modified Reynolds equation, the pressure gradient of the flow field exhibits nonlinearity for the volumetric flow rate. When the fracture is rougher, the nonlinear coefficient increases, enhancing the nonlinearity between the pressure gradient and the volumetric flow. Therefore, the modified Reynolds equation can better represent the nonlinear seepage characteristics of fluids within rough rock fractures. The accuracy of the coupled model regarding the concentration field distribution within the three-dimensional parallel plate fracture and the evolution of the one-dimensional fracture inlet opening is verified using COMSOL multi-physical field coupling software. The theoretical analysis results closely align with numerical analysis, indicating that the model can effectively represent the concentration field distribution and aperture evolution. The research presented in this study can be a predictive method for the dissolution evolution of dam bedrock cracks.
- 1 May 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (5)
A novel fracture dissolution model considering the nonlinear flow capacity of rough fractures
Existing research rarely considers the effects of rough fracture seepage on the progressive evolution processes of each physical field, and it primarily focuses on two-dimensional conditions. This study proposes a method to couple the Forchheimer equation with the Reynolds equation with time-varying apertures. The nonlinear flow of three-dimensional fractures under dissolution conditions is achieved. Then, the modified Reynolds equation under steady-state conditions is compared to the flow field governed by the Reynolds equation, and the validity of the modified Reynolds equation after coupling with the Forchheimer equation is verified. The results indicated that the maximum velocity of the flow field controlled by the modified Reynolds equation is slightly lower than that of the flow field controlled by the Reynolds equation, although the overall distribution trends are consistent. Under the control of the modified Reynolds equation, the pressure gradient of the flow field exhibits nonlinearity for the volumetric flow rate. When the fracture is rougher, the nonlinear coefficient increases, enhancing the nonlinearity between the pressure gradient and the volumetric flow. Therefore, the modified Reynolds equation can better represent the nonlinear seepage characteristics of fluids within rough rock fractures. The accuracy of the coupled model regarding the concentration field distribution within the three-dimensional parallel plate fracture and the evolution of the one-dimensional fracture inlet opening is verified using COMSOL multi-physical field coupling software. The theoretical analysis results closely align with numerical analysis, indicating that the model can effectively represent the concentration field distribution and aperture evolution. The research presented in this study can be a predictive method for the dissolution evolution of dam bedrock cracks.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Investigating the seepage behavior through rough fractures during rotational shearing
This study explores the effects of confining pressure Pz, shear displacement u, and rotational shear angle θ on the nonlinear hydraulic behavior during the rotational shearing of rough rock fractures. A model for fractures under rotational shear was first established, and subsequent seepage tests were carried out at various flow rates. The data revealed a strong correlation between the hydraulic gradient and flow rate by Forchheimer's law. The coefficients of the inertial and non-inertial terms of Forchheimer's law decreased in two distinct phases with increasing u. Both Pz and θ were found to enhance these coefficients, with the effect being more pronounced at a smaller u. The critical Reynolds number Rec increased by up to 2.58 times as u ranged from 1 to 15 mm, with a higher Pz and the θ corresponding to lower Rec values. The Forchheimer coefficient decreased rapidly with increasing u due to dilatancy effects, and the rate of decrease slowed as these effects diminished. Increases in Pz and θ led to a concomitant rise in β, although the influence of u and Pz on β was mitigated by the increase in θ. By solving the Navier–Stokes equations, simulations of the seepage flow in a fracture under rotational shear were conducted. The simulation results indicate that as rotational shearing occurs, the number of streamlines within the fracture decreases, while the number of vortices increases. The findings may offer some insight for underground space development projects.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Investigating the seepage behavior through rough fractures during rotational shearing
This study explores the effects of confining pressure Pz, shear displacement u, and rotational shear angle θ on the nonlinear hydraulic behavior during the rotational shearing of rough rock fractures. A model for fractures under rotational shear was first established, and subsequent seepage tests were carried out at various flow rates. The data revealed a strong correlation between the hydraulic gradient and flow rate by Forchheimer's law. The coefficients of the inertial and non-inertial terms of Forchheimer's law decreased in two distinct phases with increasing u. Both Pz and θ were found to enhance these coefficients, with the effect being more pronounced at a smaller u. The critical Reynolds number Rec increased by up to 2.58 times as u ranged from 1 to 15 mm, with a higher Pz and the θ corresponding to lower Rec values. The Forchheimer coefficient decreased rapidly with increasing u due to dilatancy effects, and the rate of decrease slowed as these effects diminished. Increases in Pz and θ led to a concomitant rise in β, although the influence of u and Pz on β was mitigated by the increase in θ. By solving the Navier–Stokes equations, simulations of the seepage flow in a fracture under rotational shear were conducted. The simulation results indicate that as rotational shearing occurs, the number of streamlines within the fracture decreases, while the number of vortices increases. The findings may offer some insight for underground space development projects.
- 6 May 2023
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 30 (12) , 2482-2493
Influence of notch volume on mechanical properties of a novel high-strength and high-toughness steel
- 6 May 2023
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 30 (12) , 2482-2493
Influence of notch volume on mechanical properties of a novel high-strength and high-toughness steel
- 24 September 2022
- Published by Springer Nature in Journal of Mountain Science
- Vol. 19 (9) , 2729-2741
Geomechanics model test and numerical simulation of 2G-NPR bolt support effect in an active fault tunnel
- 24 September 2022
- Published by Springer Nature in Journal of Mountain Science
- Vol. 19 (9) , 2729-2741
Geomechanics model test and numerical simulation of 2G-NPR bolt support effect in an active fault tunnel
- 4 August 2022
- Published by Springer Nature in Journal of Mountain Science
- Vol. 19 (8) , 2435-2448
Negative Poisson’s ratio and peripheral strain of an NPR anchor cable
- 4 August 2022
- Published by Springer Nature in Journal of Mountain Science
- Vol. 19 (8) , 2435-2448
Negative Poisson’s ratio and peripheral strain of an NPR anchor cable
- 11 March 2021
- Published by Springer Nature in Journal of Mountain Science
- Vol. 18 (3) , 764-778
Model test on support scheme for carbonaceous slate tunnel in high geostress zone at high depth
- 11 March 2021
- Published by Springer Nature in Journal of Mountain Science
- Vol. 18 (3) , 764-778
Model test on support scheme for carbonaceous slate tunnel in high geostress zone at high depth
- 23 December 2020
- Published by Springer Nature in Journal of Mountain Science
- Vol. 17 (12) , 2997-3011
Stability analysis of open-pit gold mine slopes and optimization of mining scheme in Inner Mongolia, China
- 23 December 2020
- Published by Springer Nature in Journal of Mountain Science
- Vol. 17 (12) , 2997-3011
Stability analysis of open-pit gold mine slopes and optimization of mining scheme in Inner Mongolia, China