Tsung-Yen Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tsung-Yen Liu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Mu-Jen Lai
Jiangxi Litkconn Academy of Optical Research Company Ltd., Longnan, China
2 shared publications- Ray-Ming Lin
Department of Electronic Engineering, Chang Gung University, Taoyuan 33302, Taiwan
2 shared publications Rui-Sen Liu
Jiangxi Litkconn Academy of Optical Research Company Ltd., Longnan, China
2 shared publicationsShih-Ming Huang
Department of Radiation Oncology, Chang Gung Memorial Hospital, Keelung, Taiwan
2 shared publicationsYi-Tsung Chang
Department of Physics, School of Science, Jimei University, Xiamen, China
2 shared publicationsCheng-Che Lee
Graduate Institute of Electronics Engineering, National Taiwan University, Taipei, Taiwan
1 shared publication
Latest Publications
- Open Access
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 129874-129880
Epoxy Molding Compound Lead Frames With Silicone Resin for Encapsulating AlGaN-Based UVB Light-Emitting Diodes
In this paper we report epoxy molding compound lead frames (EMC-LFs) with encapsulated silicone as a simple and inexpensive packaging for AlGaN-based ultraviolet-B (UVB) light-emitting diodes (LEDs) displaying high light extracting efficiencies (LEE) and long operation lifetimes. The convex surfaces and beveled shapes obtained after curing the encapsulated silicone surrounding the UVB-LED chips significantly enhanced the light output power (LOP). With silicone present inside the EMC-LFs having bonding cavity diameters of 1.7 and 1.45 mm, the LOPs of the UVB-LEDs improved by 26 and 42%, respectively; reliability tests performed over a period of 1000 h revealed, however, that the LOPs decreased to 70 and 71%, respectively, of their initial values, but no cracks appeared in the silicone during such long-term operation. Thus, the stability of silicone-encapsulating EMC-LFs for UVB-LEDs was acceptable. When compared with AlN-based direct plating copper ceramic lead frames (AlN-DPC-LFs), our proposed packaging structure and method have the potential to lower the manufacturing cost of UVB-LEDs.
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 129874-129880
Open AccessEpoxy Molding Compound Lead Frames With Silicone Resin for Encapsulating AlGaN-Based UVB Light-Emitting Diodes
In this paper we report epoxy molding compound lead frames (EMC-LFs) with encapsulated silicone as a simple and inexpensive packaging for AlGaN-based ultraviolet-B (UVB) light-emitting diodes (LEDs) displaying high light extracting efficiencies (LEE) and long operation lifetimes. The convex surfaces and beveled shapes obtained after curing the encapsulated silicone surrounding the UVB-LED chips significantly enhanced the light output power (LOP). With silicone present inside the EMC-LFs having bonding cavity diameters of 1.7 and 1.45 mm, the LOPs of the UVB-LEDs improved by 26 and 42%, respectively; reliability tests performed over a period of 1000 h revealed, however, that the LOPs decreased to 70 and 71%, respectively, of their initial values, but no cracks appeared in the silicone during such long-term operation. Thus, the stability of silicone-encapsulating EMC-LFs for UVB-LEDs was acceptable. When compared with AlN-based direct plating copper ceramic lead frames (AlN-DPC-LFs), our proposed packaging structure and method have the potential to lower the manufacturing cost of UVB-LEDs.
- 31 August 2021
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 3 (9) , 4121-4125
Narrow-Band AlGaN-Based UVB Light-Emitting Diodes
- 31 August 2021
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 3 (9) , 4121-4125
Narrow-Band AlGaN-Based UVB Light-Emitting Diodes
- Open Access
- 16 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 224433-224438
Modulation and Refinement of In–N re-Bonding of InGaN Through in Post-Flow During a Refined Temper Fire Treatment Process
In this article, we describe a subtle method for modulating and refining the indium–nitrogen (In–N) re-bonding effect of InGaN by employing an In post-flow during temper fire ($\Delta T = 110\,^{\circ }\text{C}$ ) treatment. After optimizing the In flow rate and the temper fire treatment process, the In content in InGaN quantum wells (QWs) increased from 12.7 to 22.3% and the (102) epitaxy quality of InGaN improved, as revealed by the full-width at half-maximum (FWHM) of the X-ray diffractometry signal decreasing from 410 to 374 arcsec. In addition, the quality of a five InGaN/GaN multiple-QW epilayer surface also improved greatly when applying this technique. Merely by modulating the In post-flow rate (0, 5.6, 11.2, 16.8, 22.4, or$28.0~\mu $ mol/min), the Inx Ga 1−x N photoluminescence signal (and FWHM) changed from 449 nm (58 nm) in the absence of In post-flow during the temper fire treatment process, to 523 nm (46 nm) when the In post-flow rate was$11.2~\mu $ mol/min, and to 534 nm (55 nm) when the In post-flow rate was$28.0~\mu $ mol/min. This technique is, therefore, effective at improving the InGaN quality and compensating for the In–N bond desorption rate.- 16 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 224433-224438
Open AccessModulation and Refinement of In–N re-Bonding of InGaN Through in Post-Flow During a Refined Temper Fire Treatment Process
In this article, we describe a subtle method for modulating and refining the indium–nitrogen (In–N) re-bonding effect of InGaN by employing an In post-flow during temper fire ($\Delta T = 110\,^{\circ }\text{C}$ ) treatment. After optimizing the In flow rate and the temper fire treatment process, the In content in InGaN quantum wells (QWs) increased from 12.7 to 22.3% and the (102) epitaxy quality of InGaN improved, as revealed by the full-width at half-maximum (FWHM) of the X-ray diffractometry signal decreasing from 410 to 374 arcsec. In addition, the quality of a five InGaN/GaN multiple-QW epilayer surface also improved greatly when applying this technique. Merely by modulating the In post-flow rate (0, 5.6, 11.2, 16.8, 22.4, or$28.0~\mu $ mol/min), the Inx Ga 1−x N photoluminescence signal (and FWHM) changed from 449 nm (58 nm) in the absence of In post-flow during the temper fire treatment process, to 523 nm (46 nm) when the In post-flow rate was$11.2~\mu $ mol/min, and to 534 nm (55 nm) when the In post-flow rate was$28.0~\mu $ mol/min. This technique is, therefore, effective at improving the InGaN quality and compensating for the In–N bond desorption rate.