Mohd Amirul Naim Bin Kasiran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohd Amirul Naim Bin Kasiran has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Asmarashid Ponniran
Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia, Parit Raja, Johor, Malaysia
8 shared publications H. H. Hamzah
Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia, 86400, Parit Raja, Johor, Malaysia
3 shared publicationsM. A. Harimon
Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia, 86400, Parit Raja, Johor, Malaysia
3 shared publicationsM. H. Yatim
3 shared publications- Afarulrazi Abu Bakar
Universiti Tun Hussein Onn Malaysia
2 shared publications J.N. Jumadril
Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia, Parit Raja, Johor, Malaysia
2 shared publications
Latest Publications
- Open Access
- 11 October 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (14) , 3792-3801
Modified single‐switch bridgeless PFC SEPIC structure by eliminating circulating current and power quality improvement
In this study, a modified single‐switch bridgeless power factor correction (PFC) single‐ended primary‐inductor converter (SEPIC) structure is proposed. The major practical drawbacks of the existing structure are the presence of circulating current and high maximum current stress at the input capacitor and line diodes. Therefore, to overcome these problems, the existing structure is restructured by repositioning the line diodes in series with input inductors. Besides, the principle of design parameters optimisation is used based on the balancing energy compensation between input capacitors and output inductor. This structure is designed to operate in discontinuous conduction mode in order to achieve almost a unity power factor. The operation principle and design consideration of the modified structure is introduced in details. The experimental results demonstrate that the total harmonic distortion current is reduced from 56.3 to 4.9% after the optimisation process is performed, and at the same time the dead zones are inherently eliminated. Furthermore, it is shown that the output voltage ripple frequency is always double from the input line frequency of 50 Hz and the output voltage ripple is constantly lower than the maximum input voltage ripple. Thus, the designed parameters of the experimental converter are verified with ∼160 W of the converter output power.
- 11 October 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (14) , 3792-3801
Open AccessModified single‐switch bridgeless PFC SEPIC structure by eliminating circulating current and power quality improvement
In this study, a modified single‐switch bridgeless power factor correction (PFC) single‐ended primary‐inductor converter (SEPIC) structure is proposed. The major practical drawbacks of the existing structure are the presence of circulating current and high maximum current stress at the input capacitor and line diodes. Therefore, to overcome these problems, the existing structure is restructured by repositioning the line diodes in series with input inductors. Besides, the principle of design parameters optimisation is used based on the balancing energy compensation between input capacitors and output inductor. This structure is designed to operate in discontinuous conduction mode in order to achieve almost a unity power factor. The operation principle and design consideration of the modified structure is introduced in details. The experimental results demonstrate that the total harmonic distortion current is reduced from 56.3 to 4.9% after the optimisation process is performed, and at the same time the dead zones are inherently eliminated. Furthermore, it is shown that the output voltage ripple frequency is always double from the input line frequency of 50 Hz and the output voltage ripple is constantly lower than the maximum input voltage ripple. Thus, the designed parameters of the experimental converter are verified with ∼160 W of the converter output power.
- 15 September 2019
- Published by Penerbit UTHM in International Journal of Integrated Engineering
- Vol. 11 (6)
Characteristics of High Voltage Gain of Non-Isolated Inductor-Less DC-DC Converter
- 15 September 2019
- Published by Penerbit UTHM in International Journal of Integrated Engineering
- Vol. 11 (6)
Characteristics of High Voltage Gain of Non-Isolated Inductor-Less DC-DC Converter
- Open Access
- 1 September 2019
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 10 (3) , 1461-1468
Multilevel inverter with MPWM-LFT switching strategy for voltage THD minimization
This paper presents a proposed modified pulse width modulation – low frequency triangular (MPWM-LFT) switching strategy for minimization of voltage THD with implementation of asymmetric multilevel inverter (AMLI) topology on the reduced number of switching devices (RNSD) circuit structure. Principally, MPWM-LFT able to produce optimum angle of the output voltage level in order to minimize total harmonic distortion (THD). In this study, 5-level reduced number of switching devices circuit structure is selected as a circuit configuration for asymmetric (7-level structure) multilevel inverter. For switching strategy, MPWM used low switching frequency in producing signal and needs higher output voltage levels to achieve low total harmonic distortion. In contrast, sinusoidal pulse width modulation used high switching frequency in order to minimize total harmonic distortion. By optimizing angle at the output voltage using MPWM-LFT switching strategy, the voltage THD is lower as compared to MPWM and SPWM switching strategies. MPWM-LFT switching strategy obtains 11.6% of voltage THD for the 7-level asymmetric topology as compared to MPWM and SPWM switching strategies with the voltage THD are 21.5% and 17.5% respectively from the experimental works.
- 1 September 2019
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 10 (3) , 1461-1468
Open AccessMultilevel inverter with MPWM-LFT switching strategy for voltage THD minimization
This paper presents a proposed modified pulse width modulation – low frequency triangular (MPWM-LFT) switching strategy for minimization of voltage THD with implementation of asymmetric multilevel inverter (AMLI) topology on the reduced number of switching devices (RNSD) circuit structure. Principally, MPWM-LFT able to produce optimum angle of the output voltage level in order to minimize total harmonic distortion (THD). In this study, 5-level reduced number of switching devices circuit structure is selected as a circuit configuration for asymmetric (7-level structure) multilevel inverter. For switching strategy, MPWM used low switching frequency in producing signal and needs higher output voltage levels to achieve low total harmonic distortion. In contrast, sinusoidal pulse width modulation used high switching frequency in order to minimize total harmonic distortion. By optimizing angle at the output voltage using MPWM-LFT switching strategy, the voltage THD is lower as compared to MPWM and SPWM switching strategies. MPWM-LFT switching strategy obtains 11.6% of voltage THD for the 7-level asymmetric topology as compared to MPWM and SPWM switching strategies with the voltage THD are 21.5% and 17.5% respectively from the experimental works.
- Open Access
- 1 July 2018
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 11 (1) , 144-151
Symmetrical and Asymmetrical Multilevel Inverter Structures with Reduced Number of Switching Devices
The purpose of this study is to analyze the operation and design of symmetrical and asymmetrical multilevel inverter structures with reduced number of switching devices. In this study, the term of conventional inverter is defined as a single cascaded inverter. Specifically, the inverter operates in three complete loops and only produces 2-level and 3-level of output voltages. Usually, cascaded structure suffers from the high total harmonic distortion. Thus, by considering multilevel structure of inverter, low total harmonic distortion reduction and voltage stress reduction on switching devices can be archived. Sinusoidal pulse width modulation and modified square pulse width modulation are used as modulation techniques in switching schemes of the designed multilevel inverters. The findings indicate that, the designed multilevel structure cause low total harmonics distortion at the output voltage. Furthermore, the asymmetrical structure is producing the same output voltage levels with reduced number of switching devices compared to the symmetrical structure is experimentally confirmed. The findings show that the total harmonic distortion for 7-level (symmetrical) and 9-level (asymmetrical) are 16.45% and 15.22%, respectively.
- 1 July 2018
- Published by Institute of Advanced Engineering and Science in Indonesian Journal of Electrical Engineering and Computer Science
- Vol. 11 (1) , 144-151
Open AccessSymmetrical and Asymmetrical Multilevel Inverter Structures with Reduced Number of Switching Devices
The purpose of this study is to analyze the operation and design of symmetrical and asymmetrical multilevel inverter structures with reduced number of switching devices. In this study, the term of conventional inverter is defined as a single cascaded inverter. Specifically, the inverter operates in three complete loops and only produces 2-level and 3-level of output voltages. Usually, cascaded structure suffers from the high total harmonic distortion. Thus, by considering multilevel structure of inverter, low total harmonic distortion reduction and voltage stress reduction on switching devices can be archived. Sinusoidal pulse width modulation and modified square pulse width modulation are used as modulation techniques in switching schemes of the designed multilevel inverters. The findings indicate that, the designed multilevel structure cause low total harmonics distortion at the output voltage. Furthermore, the asymmetrical structure is producing the same output voltage levels with reduced number of switching devices compared to the symmetrical structure is experimentally confirmed. The findings show that the total harmonic distortion for 7-level (symmetrical) and 9-level (asymmetrical) are 16.45% and 15.22%, respectively.
- Open Access
- 10 April 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 995 (1) , 012061
A Single Phase 7-Level Cascade Inverter Topology with Reduced Number of Switches on Resistive Load by Using PWM
This paper discussing design principles of inverter structure with reduced number of semiconductor devices of seven levels symmetric H-bridge multilevel inverter (MLI) topology. The aim of this paper is to design an inverter circuit with reduction of semiconductor losses, converter size and development cost. The H-bridge and auxiliary structures were considered in order to achieve seven levels output voltage. The performance of design circuit is compared with conventional seven levels structure in terms of voltage output. The circuit development consists of seven switches and three diode. A basic modulation technique is used to confirm the designed circuit. The results show that the designed circuit is able to convert seven level output voltage with low total harmonics distortion (THD) in voltage fundamental output. According to the results, fundamental output voltage is increased up to 8.314%, and the THD is decreased up to 0.81% compared to the conventional seven level inverter.
- 10 April 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 995 (1) , 012061
Open AccessA Single Phase 7-Level Cascade Inverter Topology with Reduced Number of Switches on Resistive Load by Using PWM
This paper discussing design principles of inverter structure with reduced number of semiconductor devices of seven levels symmetric H-bridge multilevel inverter (MLI) topology. The aim of this paper is to design an inverter circuit with reduction of semiconductor losses, converter size and development cost. The H-bridge and auxiliary structures were considered in order to achieve seven levels output voltage. The performance of design circuit is compared with conventional seven levels structure in terms of voltage output. The circuit development consists of seven switches and three diode. A basic modulation technique is used to confirm the designed circuit. The results show that the designed circuit is able to convert seven level output voltage with low total harmonics distortion (THD) in voltage fundamental output. According to the results, fundamental output voltage is increased up to 8.314%, and the THD is decreased up to 0.81% compared to the conventional seven level inverter.
- Open Access
- 10 April 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 995 (1) , 012062
A Study of 4-level DC-DC Boost Inverter with Passive Component Reduction Consideration
This study is to analyze design principles of boost inductor and capacitor used in the 4-level DC-DC boost converter to realize size reduction of passive component referring to their attributes. The important feature of this circuit is that most of the boost-up energy is transferred from the capacitor-clamped to the output side which the small inductance can be used at the input side. The inductance of the boost inductor is designed by referring the inductor current ripple. On the other hand, the capacitance of the capacitor-clamped is designed by considering voltage stress on semiconductor devices and also the used switching frequency. Besides that, according to the design specifications, the required inductance in 4-level DC-DC boost converter is decreased compared to a conventional conventional DC-DC boost converter. Meanwhile, voltage stress on semiconductor device is depending on the maximum voltage ripple of the capacitor-clamped. A 50 W 4-level DC-DC boost converter prototype has been constructed. The results show that the inductor current ripple was 1.15 A when the inductors, 1 mH and 0.11 mH were used in the conventional and 4-level DC-DC boost converters, respectively. Thus, based on the experimental results, it shows that the reduction of passive components by referring to their attributes in 4-level DC-DC boost converter is achieved. Moreover, the decreasing of voltage stress on the semiconductor devices is an advantage for the selection of low ON-resistance of the devices which will contribute to the reduction of the semiconductor conduction loss. The integration result of boost converter and H-bridge inverter is also shown.
- 10 April 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 995 (1) , 012062
Open AccessA Study of 4-level DC-DC Boost Inverter with Passive Component Reduction Consideration
This study is to analyze design principles of boost inductor and capacitor used in the 4-level DC-DC boost converter to realize size reduction of passive component referring to their attributes. The important feature of this circuit is that most of the boost-up energy is transferred from the capacitor-clamped to the output side which the small inductance can be used at the input side. The inductance of the boost inductor is designed by referring the inductor current ripple. On the other hand, the capacitance of the capacitor-clamped is designed by considering voltage stress on semiconductor devices and also the used switching frequency. Besides that, according to the design specifications, the required inductance in 4-level DC-DC boost converter is decreased compared to a conventional conventional DC-DC boost converter. Meanwhile, voltage stress on semiconductor device is depending on the maximum voltage ripple of the capacitor-clamped. A 50 W 4-level DC-DC boost converter prototype has been constructed. The results show that the inductor current ripple was 1.15 A when the inductors, 1 mH and 0.11 mH were used in the conventional and 4-level DC-DC boost converters, respectively. Thus, based on the experimental results, it shows that the reduction of passive components by referring to their attributes in 4-level DC-DC boost converter is achieved. Moreover, the decreasing of voltage stress on the semiconductor devices is an advantage for the selection of low ON-resistance of the devices which will contribute to the reduction of the semiconductor conduction loss. The integration result of boost converter and H-bridge inverter is also shown.
- Open Access
- 1 December 2017
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 8 (4) , 1948-1953
A Study on 3-phase Interleaved DC-DC Boost Converter Structure and Operation for Input Current Stress Reduction
This paper analyses a 3-phase interleaved DC-DC boost converter for the conversion of low input voltage with high input current to higher DC output voltage. The operation of the 3-phase interleaved DC-DC boost converter with multi-parallel of boost converters is controlled by interleaved of switching signals with 120 degrees phase-shifted. Therefore, with this circuit configuraion, high input current is evenly shared among the parallel units and consequently the current stress is reduced on the circuit and semiconductor devices and contributes reduction of overall losses. The simulation and hardware results show that the current stress and the semiconductor conduction losses were reduced approximately 33% and 32%, respectively in the 3-phase interleaved DC-DC boost converter compared to the conventional DC-DC boost converters. Furthermore, the use of interleaving technique with continuous conduction mode on DC-DC boost converters is reducing input current and output voltage ripples to increase reliability and efficiency of boost converters.
- 1 December 2017
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 8 (4) , 1948-1953
Open AccessA Study on 3-phase Interleaved DC-DC Boost Converter Structure and Operation for Input Current Stress Reduction
This paper analyses a 3-phase interleaved DC-DC boost converter for the conversion of low input voltage with high input current to higher DC output voltage. The operation of the 3-phase interleaved DC-DC boost converter with multi-parallel of boost converters is controlled by interleaved of switching signals with 120 degrees phase-shifted. Therefore, with this circuit configuraion, high input current is evenly shared among the parallel units and consequently the current stress is reduced on the circuit and semiconductor devices and contributes reduction of overall losses. The simulation and hardware results show that the current stress and the semiconductor conduction losses were reduced approximately 33% and 32%, respectively in the 3-phase interleaved DC-DC boost converter compared to the conventional DC-DC boost converters. Furthermore, the use of interleaving technique with continuous conduction mode on DC-DC boost converters is reducing input current and output voltage ripples to increase reliability and efficiency of boost converters.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 195-199
Parameters design evaluation in 3-level flying capacitor boost converter
Flying capacitor boost converter (FCBC) is one of the possible power converter for high power applications such as solar systems and electric vehicles system and so on. The aim of this paper is to establish relationship between the capacitance of the flying capacitor and output voltage ripple. 3-level FCBC prototype has been constructed for parameters design confirmation. Experimental result shows that the input current ripple is within design value. By identifying the input current ripple, the inductance of the boost inductor is estimated and it needs approximately only 25% compared to the 2-level conventional boost converter. Besides, 3-level FCBC only requires inductor core volume of 35% compared to the 2-level conventional boost converter. Moreover, it is confirmed that the relationship between the capacitance of the flying capacitor and output voltage ripple is independent. This finding is concretely proven by the simulation and experimental results. Therefore, the boost inductor and capacitance of the flying capacitor can be designed independently without considering output voltage ripple.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 195-199
Parameters design evaluation in 3-level flying capacitor boost converter
Flying capacitor boost converter (FCBC) is one of the possible power converter for high power applications such as solar systems and electric vehicles system and so on. The aim of this paper is to establish relationship between the capacitance of the flying capacitor and output voltage ripple. 3-level FCBC prototype has been constructed for parameters design confirmation. Experimental result shows that the input current ripple is within design value. By identifying the input current ripple, the inductance of the boost inductor is estimated and it needs approximately only 25% compared to the 2-level conventional boost converter. Besides, 3-level FCBC only requires inductor core volume of 35% compared to the 2-level conventional boost converter. Moreover, it is confirmed that the relationship between the capacitance of the flying capacitor and output voltage ripple is independent. This finding is concretely proven by the simulation and experimental results. Therefore, the boost inductor and capacitance of the flying capacitor can be designed independently without considering output voltage ripple.