Hong Lei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hong Lei has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ahrari
School of Systems and Computing, University of New South Wales, Australia
1 shared publication Baojian Ji
College of Electronic and Information Engineering Nanjing University of Aeronautics and Astronautics Nanjing Jiangsu People's Republic of China
1 shared publication- Feng Hong
Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication - Kalyanmoy Deb
Department of Computer and Electrical Engineering, Michigan State University, USA and Department of Computer Science, University of Alabama, Tuscaloosa, USA
1 shared publication Longchun Li
College of Electronic and Information Engineering Nanjing University of Aeronautics and Astronautics Nanjing Jiangsu People's Republic of China
1 shared publication- Montassar Aidi Sharif
Artificial Intelligence Engineering Technology Department, Technical Engineering College for Computer and AI/Kirkuk, Northern Technical University (NTU), Mosul 41002, Iraq
1 shared publication
Latest Publications
- Open Access
- 9 August 2017
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 10 (13) , 1740-1750
Buck Inverter without Shoot through
A new buck inverter without shoot‐through problem is presented and analysed in this study. The traditional dual‐buck inverter has been proposed to solve the shoot‐through problem of bridge‐type inverters, eliminate the dead‐time effect and improve the reliability along with the conversion efficiency. However, the existing dual‐buck inverter is prone to result in the problem of circulation and low utilisation rate of input voltage in half‐bridge‐type inverters. Besides, two or even four inductors are needed in the traditional dual‐buck inverter configuration, which leads to a larger volume and weight. In this study, single inductor and single power are used in the proposed buck inverter topology. The operating circuit is equivalent to a buck circuit during each mode, and only one switch works in high‐frequency condition at any time. A 1‐kW prototype is established and tested in this study. The results of simulation and experiments verify the validity of the theoretical analysis, along with the good performance in situations where small size, high conversion efficiency and high stability are required.
- 9 August 2017
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 10 (13) , 1740-1750
Open AccessBuck Inverter without Shoot through
A new buck inverter without shoot‐through problem is presented and analysed in this study. The traditional dual‐buck inverter has been proposed to solve the shoot‐through problem of bridge‐type inverters, eliminate the dead‐time effect and improve the reliability along with the conversion efficiency. However, the existing dual‐buck inverter is prone to result in the problem of circulation and low utilisation rate of input voltage in half‐bridge‐type inverters. Besides, two or even four inductors are needed in the traditional dual‐buck inverter configuration, which leads to a larger volume and weight. In this study, single inductor and single power are used in the proposed buck inverter topology. The operating circuit is equivalent to a buck circuit during each mode, and only one switch works in high‐frequency condition at any time. A 1‐kW prototype is established and tested in this study. The results of simulation and experiments verify the validity of the theoretical analysis, along with the good performance in situations where small size, high conversion efficiency and high stability are required.
- 19 April 2017
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 12 (3) , 036010
Reliable underwater dipole source characterization in 3D space by an optimally designed artificial lateral line system
Inspired by the lateral line of aquatic vertebrates, an artificial lateral line (ALL) system can localize and track an underwater moving object by analyzing the ambient flow caused by its motion. There are several studies on object detection, localization and tracking by ALL systems, but only a few have investigated the optimal design of the ALL system, the one that on average provides the highest characterization accuracy. Design optimization is particularly important because the uncertainties in the employed flow model and in sensor measurements deteriorate the reliability of sensing. This study investigates the optimal design of the ALL system in three-dimensional (3D) space for dipole source characterization. It highlights some challenges specific to the 3D setting and demonstrates the shortcomings of the designs in which all sensors and their sensing directions are in the same plane. As an alternative, it proposes two design concepts, called 'Offset Strategy' and 'Angle Strategy' to overcome these shortcomings. It investigates potentials of having a swarm of cooperative ALLs as well. It performs design optimization in the presence of sensor and model uncertainties and analyzes the trade-off between the number of sensors and characterization accuracy. The obtained solutions are analyzed to reveal their strategies in solving the problem efficiently. The dependency of the optimized solutions on the uncertainties is also demonstrated.
- 19 April 2017
- Published by IOP Publishing in Bioinspiration & Biomimetics
- Vol. 12 (3) , 036010
Reliable underwater dipole source characterization in 3D space by an optimally designed artificial lateral line system
Inspired by the lateral line of aquatic vertebrates, an artificial lateral line (ALL) system can localize and track an underwater moving object by analyzing the ambient flow caused by its motion. There are several studies on object detection, localization and tracking by ALL systems, but only a few have investigated the optimal design of the ALL system, the one that on average provides the highest characterization accuracy. Design optimization is particularly important because the uncertainties in the employed flow model and in sensor measurements deteriorate the reliability of sensing. This study investigates the optimal design of the ALL system in three-dimensional (3D) space for dipole source characterization. It highlights some challenges specific to the 3D setting and demonstrates the shortcomings of the designs in which all sensors and their sensing directions are in the same plane. As an alternative, it proposes two design concepts, called 'Offset Strategy' and 'Angle Strategy' to overcome these shortcomings. It investigates potentials of having a swarm of cooperative ALLs as well. It performs design optimization in the presence of sensor and model uncertainties and analyzes the trade-off between the number of sensors and characterization accuracy. The obtained solutions are analyzed to reveal their strategies in solving the problem efficiently. The dependency of the optimized solutions on the uncertainties is also demonstrated.