SSSanjeew Kumar Singh

Sanjeew Kumar Singh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sanjeew Kumar Singh has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Heavy Metal Leachability Tendency of Ladle Furnace Steel Slags: Investigating Stable Slag Matrix for Construction Use

    by Jyoti Ahlawat, S. K. Singh, Soumitra Maiti

    The leachability potential of ladle furnace steel slag (LFSS) is critical for assessing environmental compatibility and sustainability in construction applications. This study systematically investigates the leaching behavior of different LFSS types, focusing on the mobilization of environmentally sensitive heavy metals. Three LFSS variants such as Al‐killed, Al‐Si‐killed, and Si‐killed, produced from different steelmaking routes were examined using standardized protocols: the Toxicity Characteristic Leaching Procedure (TCLP), the Single Batch Test (SBT), and the Long‐Term Leaching Test (LTLT). Experimental variables included leaching medium pH, slag particle size, liquid‐to‐solid (L/S) ratio, and duration. Results reveal variations in leachate composition, specifically in release of the heavy metals that is, Cr, As, Cd, Hg, Pb, Mn, Fe, Co, Ni, Zn, Cu, and Mo. Findings indicate that metal mobilization depends on both slag chemistry and leaching environment acidity, with enhanced leaching under acidic conditions. A comparative analysis shows that Al‐Si‐killed LFSS has the lowest leaching potential, indicating more stable immobilization and precipitation of heavy metals. In contrast, Al‐killed and Si‐killed LFSS show higher leaching, particularly increased manganese release under acidic and alkaline conditions. However, concentrations of other heavy metals remain negligible and within regulatory limits. Long‐term leaching assessments confirm the environmental safety of the tested LFSS variants. Al‐Si killed LFSS found to exhibit lowest or negligible leaching of toxic trace metals particularly in TCLP test. This behavior is attributed to the formation of stable alumino‐silicate network and surface passivation layer which binds the metallic species within the matrix and reduces the mobility. The results support the safe and sustainable use of LFSS in construction. Incorporating suitable binders further reduces leachability by encapsulation and masking effects, enhancing performance.

  • Upcycling of construction and demolition waste by oxalic acid surface activation of recycled aggregates: a novel processing approach

    by Anchal Aggarwal, Sanjeew Kumar Singh, Gaurav Goel

    The construction sector generates over 3.57 billion tons of construction and demolition waste (CDW) globally each year. However, the large- scale use of recycled aggregates (RA) in concrete remains constrained by adhered mortar and inferior physico- mechanical performance. The literature indicates that inorganic acids can deteriorate aggregate integrity and weaken concrete durability. Therefore, this study explores the use of organic oxalic acid (C2H2O4) as a surface- modification strategy. Advanced characterisation of the processed RA using XRD, FESEM- EDS, FTIR, TGA and TEM- EDS confirmed the formation of surface calcium oxalate, calcium redistribution and pozzolanic crystalline deposits, leading to improved interfacial densification. The results demonstrate that organic acid treatment reduced the impact value by 4.6% and 5.9% compared to H2SO4- and HCl- treated aggregates, respectively. The water absorption of RA decreased from 3.68% (untreated) to 2.80% (H2SO4- treated), 2.75% (HCl- treated), and further to 2.45% with oxalic acid treatment, indicating improved surface densification and reduced accessible porosity. This indicates surface pore refinement and reduced porosity. The compressive and splitting tensile strengths increased by 29.5% and 35.2%, respectively, at 28 days, compared to untreated RA concrete. The superior performance of oxalic acid was associated with the combined effects of adhered mortar modification and calcium oxalate-rich surface formation rather than mortar removal alone. The use of organic oxalic acid offers practical advantages over hazardous inorganic acids, including comparatively reduced handling and storage hazards. A preliminary screening-level carbon and life- cycle assessment (LCA) further indicated its potential environmental advantage, thereby minimising safety concerns and operational costs for large- scale construction applications. The findings establish oxalic acid treatment as a sustainable route to produce high- performance RA for circular concrete applications. Graphical Abstract

  • Quaternary blended composite cement—a pathway to sustainable and circular construction

    by Sanjeew Kumar Singh, Jyoti Ahlawat

    The depletion of natural resources and the substantial carbon emissions associated with ordinary Portland cement (OPC) production pose critical environmental challenges to the construction sector. This study investigates the development of a sustainable quaternary blended cement system incorporating steel and iron industry by-products, i.e. Linz-Donawitz slag (LDS), ladle furnace slag (LFS), and ground granulated blast furnace slag (GGBFS), in combination with OPC. Binder pastes were formulated with varying proportions of LDS and LFS, while maintaining OPC at 50% and GGBFS at 10% by mass. The blended systems were comprehensively evaluated with respect to mechanical performance, durability in aggressive environments, phase assemblage, microstructural characteristics, and thermogravimetric behaviour. The optimised composition, consisting of OPC (50%), GGBFS (10%), LDS (20%), LFS (20%), and 10% chemical activator, achieved a 28-day compressive strength of 62.9 MPa, significantly surpassing the OPC control (53.4 MPa). Microstructural and mineralogical analysis confirmed the formation of a dense and homogeneous calcium silicate hydrate (C-S-H) gel network, consistent with thermogravimetric findings indicating enhanced hydration and reduced portlandite content. Durability assessment of the optimised mix demonstrated superior resistance to exposure to MgSO₄ and HCl. The control mix showed weight changes of 0.70% and 0.64% in the presence of MgSO4 and HCl, respectively, while the optimised mix exhibited the lowest gains at 0.45% and 0.49%, respectively. Furthermore, exposure to sulphate and acid solutions reduces strength. The control mix exhibited strength losses of 6.37% and 9.55% under sulphate and acid exposure, whereas the optimised mix demonstrated comparatively lower reductions of 1.74% and 5.08%, respectively. The ingress of sulphate and chloride ions from the MgSO4 and HCl solution into the pore structure of the binder matrix initiates chemical reactions with the calcium hydroxide and monosulphate phases, leading to the formation of expansive products, such as gypsum and ettringite. Although a marginal increase in drying shrinkage of the optimised mix (0.038%) compared with the control (0.034%) was observed, the overall durability performance remained superior to that of conventional OPC systems. The optimised blends met the requirements of Indian and ASTM standards for OPC 43-grade cement, confirming their technical viability for practical implementation. Beyond performance improvements, the study highlights significant sustainability and economic implications. Partial substitution of clinker with steel and iron slags reduces embodied CO₂ emissions, diverts industrial by-products from landfills, and advances circular economy principles within the construction industry. While initial production costs are comparable to conventional OPC due to supplementary cementitious material processing, lifecycle benefits, including reduced clinker demand, improved durability, extended service life, and potential environmental incentives, enhance overall cost-effectiveness. In conclusion, this research establishes steel and iron slags as viable constituents in high-performance quaternary blended cements. By demonstrating enhanced strength, improved durability, regulatory compliance, and environmental benefits, the study provides a practical pathway for lowering the carbon footprint of cementitious materials.


  • Seismic hazard assessment of existing reinforced concrete bridge structure using pushover analysis

    by Mohd Firoj, Sauhardra Ojha, Prince Poddar, Sanjeew Kumar Singh

    The present paper focuses on the nonlinear static pushover analysis of a 3-span existing RC bridge located in Indian seismic Zone IV as per IS1893-2016 using the Finite Element Method (FEM). The 3D model of the RC bridge is simulated using the FEM technique and pushover analysis is performed to analyze the structure for modal mass participating ratio, performance level, spectral demand, and capacity of the structure. The bridge pier and longitudinal girder are modeled using the two noded beam element and bent cap and abutment of the bridge structure is modeled using the 8 noded brick element. The base of the column is assumed fixed condition. The pushover analysis is performed using Displacement Modification (FEMA 440) and Capacity Spectrum Method (ATC 40). The outcomes of results appear that the considered bridge has inadequate capacity to cope up with any of the desired performance levels because spectral demand is greater than the spectral capacity. The modal analysis of the 3D bridge exposes that it has many closely-spaced modes. The mass participating ratio for the higher modes is not very high. After performing pushover analysis of the exiting RC bridge structure it has been concluded that the existing bridge structure does not meet seismic criteria of spectral demand as per the ATC 40 and FEMA 440, therefore retrofitting is required for bridge component i.e. piers, abutment, and bent cap.