Mahmood Hasan Oudah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mahmood Hasan Oudah has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Mohammed Kadhim Allawi
Department of Mechanical Power Engineering, Baghdad-Technical Engineering College, Middle Technical University, Baghdad, Iraq
4 shared publications - Mohanad Kadhim Mejbel
Department of Materials Engineering Technology , Technical Engineering College-Baghdad , Middle Technical University , Baghdad 10074 , Iraq , mtu.edu.iq
3 shared publications Zahraa Kareem Yasser
2 shared publicationsKifah H. Hilal
1 shared publicationMohanad Kadhim Mejbel
1 shared publicationWajdi Qassim Hussen
1 shared publication
Latest Publications
- 19 June 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (19) , 21491-21525
Slug-Flow-Induced Vibration in Curved Piping Systems: Mechanisms, Modeling, and Thermal Coupling
- 19 June 2026
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (19) , 21491-21525
Slug-Flow-Induced Vibration in Curved Piping Systems: Mechanisms, Modeling, and Thermal Coupling
- 22 January 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 211
Low-GWP refrigerants performance evaluation: R513A and R515B boiling within smooth and microfinned tubes
- 22 January 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 211
Low-GWP refrigerants performance evaluation: R513A and R515B boiling within smooth and microfinned tubes
- 15 February 2024
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 60 (4) , 599-616
Comparative investigation of R1270, R290, and R600a boiling in microfin and smooth tubes
- 15 February 2024
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 60 (4) , 599-616
Comparative investigation of R1270, R290, and R600a boiling in microfin and smooth tubes
- 30 June 2023
- Published by International Information and Engineering Technology Association in Mathematical Modelling of Engineering Problems
- Vol. 10 (3) , 985-992
Effect of Notched Pin Fin Heat Sink on the Heat Transfer Performance: Numerical Study
- 30 June 2023
- Published by International Information and Engineering Technology Association in Mathematical Modelling of Engineering Problems
- Vol. 10 (3) , 985-992
Effect of Notched Pin Fin Heat Sink on the Heat Transfer Performance: Numerical Study
- Open Access
- 30 December 2020
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 17 (4)
Variable Valve Timing (VVT) Modelling by Lotus Engine Simulation Software
Variable valve timing (VVT) is an advanced modern technique applied in internal combustion engines by altering the valve lift event timing. This work aims to contribute to the continuing industrial VVT development to improve engine efficiency, fuel consumption and performance. To observe the influence on the spark-ignition (SI) engine’s performance, four valve timing strategies are selected carefully by varying the intake and exhaust valve timing. Lotus Engine Simulation, a simulation engineering software, is adapted in this study. The engine characteristics used in this modelling are spark engine, multicylinder, four strokes, port injection fuel system and constant compression ratio. A comparison between a conventional standard exhaust/intake valve timing and three other different timing cases is carried out. Results reveal that the overlap case of 98° showed a good brake-specific fuel consumption by approximately 3% less than the conventional case. An improvement of 6.2% for volume efficiency and 2.9% in brake thermal efficiency is also reported.
- 30 December 2020
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 17 (4)
Open AccessVariable Valve Timing (VVT) Modelling by Lotus Engine Simulation Software
Variable valve timing (VVT) is an advanced modern technique applied in internal combustion engines by altering the valve lift event timing. This work aims to contribute to the continuing industrial VVT development to improve engine efficiency, fuel consumption and performance. To observe the influence on the spark-ignition (SI) engine’s performance, four valve timing strategies are selected carefully by varying the intake and exhaust valve timing. Lotus Engine Simulation, a simulation engineering software, is adapted in this study. The engine characteristics used in this modelling are spark engine, multicylinder, four strokes, port injection fuel system and constant compression ratio. A comparison between a conventional standard exhaust/intake valve timing and three other different timing cases is carried out. Results reveal that the overlap case of 98° showed a good brake-specific fuel consumption by approximately 3% less than the conventional case. An improvement of 6.2% for volume efficiency and 2.9% in brake thermal efficiency is also reported.
- Open Access
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 881 (1)
Iraqi gasoline performance at low engine speeds
Four grades of gasoline fuel – obtained from Iraqi oil refineries – are used in this research to investigate their performance in spark-ignition (SI) engines. These grades are RON 77, RON 82, RON 87, and RON 93. We used a four-stroke, four-cylinder SI engine laboratory rig to conduct the experiments and calculate the engine performance for each gasoline grade. We compared the experimental results with the predicted numerical simulations carried out using a well-known commercial software called Lotus Engine Simulation (LES). The numerical results obtained using LES show good agreement with experimental findings. A higher gasoline grade shows better engine performance than lower grades owing to its superior quality and purity, better combustion characteristics and performance, and lower amount of gasoline inclusions. Gasoline fuel RON 93 provided the best engine performance in comparison to the remaining grades. The variation between the numerical and experimental results in all tested conditions was below 3%.
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 881 (1)
Open AccessIraqi gasoline performance at low engine speeds
Four grades of gasoline fuel – obtained from Iraqi oil refineries – are used in this research to investigate their performance in spark-ignition (SI) engines. These grades are RON 77, RON 82, RON 87, and RON 93. We used a four-stroke, four-cylinder SI engine laboratory rig to conduct the experiments and calculate the engine performance for each gasoline grade. We compared the experimental results with the predicted numerical simulations carried out using a well-known commercial software called Lotus Engine Simulation (LES). The numerical results obtained using LES show good agreement with experimental findings. A higher gasoline grade shows better engine performance than lower grades owing to its superior quality and purity, better combustion characteristics and performance, and lower amount of gasoline inclusions. Gasoline fuel RON 93 provided the best engine performance in comparison to the remaining grades. The variation between the numerical and experimental results in all tested conditions was below 3%.
- 11 September 2019
- Published by ZIbeline International Publishing in Journal of Mechanical Engineering Research and Developments
- Vol. 42 (5) , 211-215
ANALYSIS OF EXHAUST MANIFOLD OF SPARK-IGNITION ENGINE BY USING COMPUTATIONAL FLUID DYNAMICS (CFD)
- 11 September 2019
- Published by ZIbeline International Publishing in Journal of Mechanical Engineering Research and Developments
- Vol. 42 (5) , 211-215
ANALYSIS OF EXHAUST MANIFOLD OF SPARK-IGNITION ENGINE BY USING COMPUTATIONAL FLUID DYNAMICS (CFD)
- Open Access
- 11 September 2019
- Published by ZIbeline International Publishing in Journal of Mechanical Engineering Research and Developments
- Vol. 42 (5) , 224-231
EFFECTS OF WC, SiC, IRON AND GLASS FILLERS AND THEIR HIGH PERCENTAGE CONTENT ON ADHESIVE BOND STRENGTH OF AN ALUMINIUM ALLOY BUTT JOINT: AN EXPERIMENTAL STUDY
- 11 September 2019
- Published by ZIbeline International Publishing in Journal of Mechanical Engineering Research and Developments
- Vol. 42 (5) , 224-231
Open AccessEFFECTS OF WC, SiC, IRON AND GLASS FILLERS AND THEIR HIGH PERCENTAGE CONTENT ON ADHESIVE BOND STRENGTH OF AN ALUMINIUM ALLOY BUTT JOINT: AN EXPERIMENTAL STUDY