Meng-Jie Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Meng-Jie Wu has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chao Zhi
School of Textile Science and Engineering, Key Laboratory of Functional Textile Material and Product of the Ministry of Education Xi'an Polytechnic University Xi'an Shaanxi China
1 shared publication - Guan-Lin Wang
School of Textile science and engineering, Xi’an Polytechnic University, Xi’an, Shaanxi, 710048 China and Key Laboratory of Functional Textile Material and Product (Xi’an Polytechnic University), Ministry of Education, Xi’an, Shaanxi, 710048, China
1 shared publication - Jia-Guang Meng
School of Textile science and engineering, Xi’an Polytechnic University, Xi’an, Shaanxi, 710048 China and Key Laboratory of Functional Textile Material and Product (Xi’an Polytechnic University), Ministry of Education, Xi’an, Shaanxi, 710048, China
1 shared publication - Lingjie Yu
School of Textile Science and Engineering, Xi’an Polytechnic University, Xi’an 710048, China
1 shared publication - Menghe Miao
CSIRO Manufacturing, 75 Pigdons Road, Waurn Ponds, Victoria 3216, Australia
1 shared publication - Xin-Rui Xu
Wenshang Ruyi Technology Textile Co., Ltd., Jining, Shandong, 272500, China
1 shared publication
Latest Publications
- Open Access
- 1 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 213512-213521
3D Spacer Fabric Structure for the Prevention and Care of Pressure Ulcers
Many pressure wound protection products, such as pressure redistribution supports and exuding wound dressings, are made of polyurethane sponge. However, polyurethane sponge does not possess a desirable combination of air permeability, moisture management and mechanical properties required by pressure redistribution supports and exuding wound dressings. This study explores the optimization of a 3D warp-knitted spacer fabric (WKSF) structure for pressure ulcer protection. The influence of construction and material parameters on the compression performance and air permeability of WKSFs was investigated by numerical simulation and then validated with experiments. The moisture transport and wetting properties of WKSFs were characterized by a moisture management tester. The numerical simulation and experimental results indicate that the WKSF structure can be tuned to achieve compressional properties, air permeability, and moisture management performance that are more suitable for pressure ulcer protection than polyurethane sponge. WKSFs constructed with a low-density surface layer, coarser spacer yarns, and larger spacer yarn inclination-angle are more suitable for pressure redistribution support surfaces, while WKSFs constructed with dense surface layers and coarse spacer yarn can better meet the performance requirements of exuding wound dressings.
- 1 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 213512-213521
Open Access3D Spacer Fabric Structure for the Prevention and Care of Pressure Ulcers
Many pressure wound protection products, such as pressure redistribution supports and exuding wound dressings, are made of polyurethane sponge. However, polyurethane sponge does not possess a desirable combination of air permeability, moisture management and mechanical properties required by pressure redistribution supports and exuding wound dressings. This study explores the optimization of a 3D warp-knitted spacer fabric (WKSF) structure for pressure ulcer protection. The influence of construction and material parameters on the compression performance and air permeability of WKSFs was investigated by numerical simulation and then validated with experiments. The moisture transport and wetting properties of WKSFs were characterized by a moisture management tester. The numerical simulation and experimental results indicate that the WKSF structure can be tuned to achieve compressional properties, air permeability, and moisture management performance that are more suitable for pressure ulcer protection than polyurethane sponge. WKSFs constructed with a low-density surface layer, coarser spacer yarns, and larger spacer yarn inclination-angle are more suitable for pressure redistribution support surfaces, while WKSFs constructed with dense surface layers and coarse spacer yarn can better meet the performance requirements of exuding wound dressings.