Sushanlal Babu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sushanlal Babu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Surendran Anish
Department of Mechanical Engineering, National Institute of Technology, Surathkal, Karnataka-575025, India
3 shared publications S. Anish
National Institute of Technology
2 shared publications- A. M. Pradeep
Indian Institute of Technology Bombay
1 shared publication J. K. Tom
National Institute of Technology
1 shared publicationK. N. Kiran
National Institute of Technology
1 shared publication- Libin Panavelil Oommen
Mechanical Department, Al-Azhar College of Engineering and Technology, Idukki, 685581, Kerala, India
1 shared publication
Latest Publications
- 20 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4)
Mitigation of Secondary Flows and Pressure Side Bubble in Turbine Blade Passage Using Asymmetric Endwall Contouring: A Steady-State Analysis
In turbine passages, secondary vortices and pressure-side bubbles significantly contribute to aerodynamic losses and reduced blade efficiency issues that are critical in industrial gas turbine performance. Hence, it is very important to mitigate such losses to enhance overall turbine efficiency. Several research attempts have already been made to address this challenge; however, most studies have not focused explicitly on pressure-side bubble mitigation strategies. In the present investigation, an effort has been made to investigate the impact of endwall contouring in minimizing losses caused by secondary vortices, particularly focusing on pressure-side bubble formation. Experimental and numerical investigations are conducted on a low-speed blowing-type turbine cascade wind tunnel. The experimental study involves in-cascade testing, while numerical simulations are performed using ANSYS Reynolds-Averaged Navier-Stokes (RANS) equations with the Shear Stress Transport (SST) turbulence model. Three contouring configurations (EC1, EC2, and EC3) are compared against a non-profiled base case (BC). The results confirm that endwall curvature significantly alters secondary flow behavior and static pressure distribution. While EC1 and EC2 generated stagnant zones in the valleys, causing additional losses while the EC3 profile with optimized hump height and valley depth, redistributed pressure effectively. This effectively suppressed lateral flow migration and pressure-side bubble formation, which in turn enhanced overall turbine performance. In comparison to the base case, the EC3 design quantitatively reduced total pressure loss by 3.43%, proving its efficacy in improving aerodynamic performance.
- 20 November 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4)
Mitigation of Secondary Flows and Pressure Side Bubble in Turbine Blade Passage Using Asymmetric Endwall Contouring: A Steady-State Analysis
In turbine passages, secondary vortices and pressure-side bubbles significantly contribute to aerodynamic losses and reduced blade efficiency issues that are critical in industrial gas turbine performance. Hence, it is very important to mitigate such losses to enhance overall turbine efficiency. Several research attempts have already been made to address this challenge; however, most studies have not focused explicitly on pressure-side bubble mitigation strategies. In the present investigation, an effort has been made to investigate the impact of endwall contouring in minimizing losses caused by secondary vortices, particularly focusing on pressure-side bubble formation. Experimental and numerical investigations are conducted on a low-speed blowing-type turbine cascade wind tunnel. The experimental study involves in-cascade testing, while numerical simulations are performed using ANSYS Reynolds-Averaged Navier-Stokes (RANS) equations with the Shear Stress Transport (SST) turbulence model. Three contouring configurations (EC1, EC2, and EC3) are compared against a non-profiled base case (BC). The results confirm that endwall curvature significantly alters secondary flow behavior and static pressure distribution. While EC1 and EC2 generated stagnant zones in the valleys, causing additional losses while the EC3 profile with optimized hump height and valley depth, redistributed pressure effectively. This effectively suppressed lateral flow migration and pressure-side bubble formation, which in turn enhanced overall turbine performance. In comparison to the base case, the EC3 design quantitatively reduced total pressure loss by 3.43%, proving its efficacy in improving aerodynamic performance.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3119 (1) , 030002
A numerical analysis on effects of boundary layer fence on blade passage aerodynamics and loss reduction
Mitigation of total pressure loss and improvement in aerodynamic performance are obtained on a low aspect ratio turbine blade. The turbine blade hub region is c Mitigation of total pressure loss and improvement in aerodynamic performance are obtained on a low aspect ratio turbine blade. The turbine blade hub region is c
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3119 (1) , 030002
Open AccessA numerical analysis on effects of boundary layer fence on blade passage aerodynamics and loss reduction
Mitigation of total pressure loss and improvement in aerodynamic performance are obtained on a low aspect ratio turbine blade. The turbine blade hub region is c Mitigation of total pressure loss and improvement in aerodynamic performance are obtained on a low aspect ratio turbine blade. The turbine blade hub region is c
- 1 June 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (6)
Transient nature of secondary vortices in an axial compressor stage with a tandem rotor
An efficient and compact design of a compressor continues to be a challenging area of research. The unavoidable streamwise adverse pressure gradient together with passage transverse pressure gradient restricts the maximum allowable blade turning. Tandem blading is an interesting concept for increasing the pressure rise by permitting a higher blade turning angle. The energized flow through the tandem blade nozzle gap helps to minimize the possibility of flow separation over the suction surface of the aft blade. However, a coherent transient analysis of a tandem rotor stage in an axial compressor is yet to be well explored. In the present paper, the complex flow field over a tandem rotor and the succeeding stator passage is analyzed in detail. Although the tandem rotor increases the flow turning and diffusion effect, the presence of separate trailing edge wakes and hub corner vortex causes early onset of flow separation over the stator suction. The flow structures developed within the rotor and the stator passages at different time instances are highlighted with the help of limiting streamlines and iso-surface Q-criterion superimposed with entropy contours. The results indicate that within the rotor passage, transient flow features are observed near the hub corner region close to the aft blade trailing edge rather than the tip region. When the rotor passes the stator leading edge, the rotor trailing edge leakage flow at the hub is entrained into the stator leading edge reverse flow region. This is then further circumferentially dragged into the mid-passage region. The interference of multiple rotor wakes with the stator leading edge leads to the formation of longitudinal and arch like separation vortices at the stator-hub and the stator-casing regions, respectively. These separation vortices grow in size while being convected downstream. Eventually, as time progresses, the vortices split and shed periodically from the stator surface. The present investigation highlights the requirement of a new stator design in a tandem rotor–conventional stator configuration. Such designs could further magnify the significant aerodynamic performance obtained using a tandem configuration.
- 1 June 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (6)
Transient nature of secondary vortices in an axial compressor stage with a tandem rotor
An efficient and compact design of a compressor continues to be a challenging area of research. The unavoidable streamwise adverse pressure gradient together with passage transverse pressure gradient restricts the maximum allowable blade turning. Tandem blading is an interesting concept for increasing the pressure rise by permitting a higher blade turning angle. The energized flow through the tandem blade nozzle gap helps to minimize the possibility of flow separation over the suction surface of the aft blade. However, a coherent transient analysis of a tandem rotor stage in an axial compressor is yet to be well explored. In the present paper, the complex flow field over a tandem rotor and the succeeding stator passage is analyzed in detail. Although the tandem rotor increases the flow turning and diffusion effect, the presence of separate trailing edge wakes and hub corner vortex causes early onset of flow separation over the stator suction. The flow structures developed within the rotor and the stator passages at different time instances are highlighted with the help of limiting streamlines and iso-surface Q-criterion superimposed with entropy contours. The results indicate that within the rotor passage, transient flow features are observed near the hub corner region close to the aft blade trailing edge rather than the tip region. When the rotor passes the stator leading edge, the rotor trailing edge leakage flow at the hub is entrained into the stator leading edge reverse flow region. This is then further circumferentially dragged into the mid-passage region. The interference of multiple rotor wakes with the stator leading edge leads to the formation of longitudinal and arch like separation vortices at the stator-hub and the stator-casing regions, respectively. These separation vortices grow in size while being convected downstream. Eventually, as time progresses, the vortices split and shed periodically from the stator surface. The present investigation highlights the requirement of a new stator design in a tandem rotor–conventional stator configuration. Such designs could further magnify the significant aerodynamic performance obtained using a tandem configuration.
- 1 January 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (1) , 015119
Aerodynamic performance of profiled endwalls with upstream slot purge flow in a linear turbine cascade having pressure side separation
In aeroengines, purge flow directly fed from the compressor (which bypasses the combustor) is introduced through the disk space between blade rows to prevent the hot ingress. Higher quantity of purge gas fed through the wheel space can provide additional thermal protection to the passage endwall and blade surfaces. However, the interaction of purge flow with the mainstream flow leads to higher secondary losses. Secondary losses inside a turbine blade passage can be reduced effectively by endwall contouring. This paper presents computational investigation on the influence of non-axisymmetric endwall contouring over endwall secondary flow modification in the presence of purge flow with the pressure side bubble (PSB). The experimental analysis was conducted for the base case without purge and base case with purge (BCP) configurations having flat endwalls. The total pressure loss coefficient and exit yaw angle deviation were measured with the help of a five-hole pressure probe. Static pressure distribution over the blade midspan was obtained by 16 channel Scanivalve. Aerodynamic performances of three different profiled endwalls are numerically analyzed and are compared against the BCP configuration. The effects of different contoured endwall geometries on endwall static pressure distribution and secondary kinetic energy were also discussed. Analysis shows that in the first contoured endwall configuration (EC1), the formation of stagnation zones at a contour valley close to the suction surface causes the exit total pressure loss coefficient to increase. The shifting of the contour valley near to the pressure surface (EC2 configuration) has resulted in local acceleration of the diverted pressure side leg of the horseshoe vortex over the hump toward the end of the passage. In the third configuration (EC3 configuration), reduced valley depth and optimum hump height have effectively redistributed the endwall pitchwise pressure gradient. The increased static pressure coefficient at the endwall near to the pressure surface has eliminated the PSB formation. In addition, computational results of unsteady Reynolds averaged Navier–Stokes simulations are obtained for analyzing transient behavior of PSB, with more emphasis on its migration on the pressure surface and transport across the blade passage. The additional work done by the mainstream fluid to transport the low momentum PSB fluid has caused higher aerodynamic penalty at the blade exit region. In this viewpoint, the implementation of contoured endwalls has shown beneficial effects by eliminating the PSB and related secondary vortices. At 27% of axial chord downstream of the blade trailing edge, a 4.1% reduction in the total pressure loss coefficient was achieved with endwall contouring.
- 1 January 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (1) , 015119
Aerodynamic performance of profiled endwalls with upstream slot purge flow in a linear turbine cascade having pressure side separation
In aeroengines, purge flow directly fed from the compressor (which bypasses the combustor) is introduced through the disk space between blade rows to prevent the hot ingress. Higher quantity of purge gas fed through the wheel space can provide additional thermal protection to the passage endwall and blade surfaces. However, the interaction of purge flow with the mainstream flow leads to higher secondary losses. Secondary losses inside a turbine blade passage can be reduced effectively by endwall contouring. This paper presents computational investigation on the influence of non-axisymmetric endwall contouring over endwall secondary flow modification in the presence of purge flow with the pressure side bubble (PSB). The experimental analysis was conducted for the base case without purge and base case with purge (BCP) configurations having flat endwalls. The total pressure loss coefficient and exit yaw angle deviation were measured with the help of a five-hole pressure probe. Static pressure distribution over the blade midspan was obtained by 16 channel Scanivalve. Aerodynamic performances of three different profiled endwalls are numerically analyzed and are compared against the BCP configuration. The effects of different contoured endwall geometries on endwall static pressure distribution and secondary kinetic energy were also discussed. Analysis shows that in the first contoured endwall configuration (EC1), the formation of stagnation zones at a contour valley close to the suction surface causes the exit total pressure loss coefficient to increase. The shifting of the contour valley near to the pressure surface (EC2 configuration) has resulted in local acceleration of the diverted pressure side leg of the horseshoe vortex over the hump toward the end of the passage. In the third configuration (EC3 configuration), reduced valley depth and optimum hump height have effectively redistributed the endwall pitchwise pressure gradient. The increased static pressure coefficient at the endwall near to the pressure surface has eliminated the PSB formation. In addition, computational results of unsteady Reynolds averaged Navier–Stokes simulations are obtained for analyzing transient behavior of PSB, with more emphasis on its migration on the pressure surface and transport across the blade passage. The additional work done by the mainstream fluid to transport the low momentum PSB fluid has caused higher aerodynamic penalty at the blade exit region. In this viewpoint, the implementation of contoured endwalls has shown beneficial effects by eliminating the PSB and related secondary vortices. At 27% of axial chord downstream of the blade trailing edge, a 4.1% reduction in the total pressure loss coefficient was achieved with endwall contouring.
- 19 February 2020
- Published by Springer Nature
- p. 161-172
Numerical Investigation on Effects of Profiled Endwall Over Purge Flow in Linear Turbine Cascade
- 19 February 2020
- Published by Springer Nature
- p. 161-172
Numerical Investigation on Effects of Profiled Endwall Over Purge Flow in Linear Turbine Cascade
- 1 January 2020
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 13 (1) , 335-347
Computational Predictions of Velocity Ratio and Ejection Angle on Purge Flow in a Linear Turbine Cascade with Upstream Disturbance
- 1 January 2020
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 13 (1) , 335-347
Computational Predictions of Velocity Ratio and Ejection Angle on Purge Flow in a Linear Turbine Cascade with Upstream Disturbance