Zhenyu Deng
Zhenyu Deng has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Dan Luo
State Key Laboratory of Power Transmission Equipment & System Security and New Technology, Chongqing University, Chongqing, China
2 shared publications - Hongjian Xia
State Key Lab of Power Transmission Equipment & System Security and New Technology, School of Electrical Engineering, Chongqing University, Chongqing 400044, China
2 shared publications - Minyou Chen
State Key Laboratory of Power Transmission Equipment and System Security and New Technology, School of Electrical Engineering, Chongqing University, Chongqing, China
2 shared publications - Wei Lai
State Key Laboratory of Power Transmission Equipment and System Security and New Technology, School of Electrical Engineering, Chongqing University, Chongqing, China
2 shared publications - Kai Yu
CRRC Yong Ji Electric Co., Ltd., Yongji 044502, China
1 shared publication - Xueni Ding
State Grid Jiangsu Electric Power Company Limited Suzhou Power Supply Company, Suzhou, China
1 shared publication
Latest Publications
- Open Access
- 24 March 2022
- Published by MDPI AG in Electronics
- Vol. 11 (7) , 1021
A Fault Detection Method of IGBT Bond Wire Fatigue Based on the Reduction of Measured Heatsink Thermal Resistance
Bond wire lift-off is one of the major failure mechanisms in the insulated gate bipolar transistor (IGBT) modules. Detecting the fault of bond wires is important to avoid the open-circuit fault of IGBT to ensure the reliable operation of power converters. In this paper, we propose a novel bond wire fatigue detection method for IGBT, which could be used in normal working conditions. Firstly, we investigated the dependence of bond wire fatigue on heatsink thermal resistance. An aging rate K was proposed to compare the measured thermal resistance with the initial value, which could indicate the bond wire fatigue. Then, this proposed method was verified by simulation and experimental results under different current levels. Finally, a power cycling test was used to show the aging process of the IGBT module, which shows the feasibility of proposed method.
- 24 March 2022
- Published by MDPI AG in Electronics
- Vol. 11 (7) , 1021
Open AccessA Fault Detection Method of IGBT Bond Wire Fatigue Based on the Reduction of Measured Heatsink Thermal Resistance
Bond wire lift-off is one of the major failure mechanisms in the insulated gate bipolar transistor (IGBT) modules. Detecting the fault of bond wires is important to avoid the open-circuit fault of IGBT to ensure the reliable operation of power converters. In this paper, we propose a novel bond wire fatigue detection method for IGBT, which could be used in normal working conditions. Firstly, we investigated the dependence of bond wire fatigue on heatsink thermal resistance. An aging rate K was proposed to compare the measured thermal resistance with the initial value, which could indicate the bond wire fatigue. Then, this proposed method was verified by simulation and experimental results under different current levels. Finally, a power cycling test was used to show the aging process of the IGBT module, which shows the feasibility of proposed method.
- Open Access
- 15 January 2021
- Published by MDPI AG in Electronics
- Vol. 10 (2) , 194
A Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement
Bond wire lift-off will cause an increase of remaining wires’ power dissipation, which usually is ignored for healthy modules. However, only partial wires’ power dissipation transfers through thermal path from junction to case, which will lead to overestimate the whole power dissipation from collector to emitter pole and underestimate the calculated thermal resistance using the proportion of temperature difference to power dissipation. A FEM model is established to show the change of heat flow after bond wires were removed, the temperature of bond wires increases, and the measured thermal resistance decrease after bond wires lift-off. It is validated by experimental results using open package Insulated Gate Bipolar Transistor (IGBT) modules under different current conditions. This conclusion might be helpful to indicate the bond wires lift-off and solder fatigue by comparing the change of measured thermal resistance. Using the Kelvin setup to measure thermal resistance will cause misjudgment of failure mode due to the ignoring of wires’ power dissipation. This paper proposed that the lift-off of bond wires will lead to underestimating the thermal resistance measurement, which will overestimate the lifetime of IGBT module and misjudge its state of health.
- 15 January 2021
- Published by MDPI AG in Electronics
- Vol. 10 (2) , 194
Open AccessA Study on the Effect of Bond Wires Lift-Off on IGBT Thermal Resistance Measurement
Bond wire lift-off will cause an increase of remaining wires’ power dissipation, which usually is ignored for healthy modules. However, only partial wires’ power dissipation transfers through thermal path from junction to case, which will lead to overestimate the whole power dissipation from collector to emitter pole and underestimate the calculated thermal resistance using the proportion of temperature difference to power dissipation. A FEM model is established to show the change of heat flow after bond wires were removed, the temperature of bond wires increases, and the measured thermal resistance decrease after bond wires lift-off. It is validated by experimental results using open package Insulated Gate Bipolar Transistor (IGBT) modules under different current conditions. This conclusion might be helpful to indicate the bond wires lift-off and solder fatigue by comparing the change of measured thermal resistance. Using the Kelvin setup to measure thermal resistance will cause misjudgment of failure mode due to the ignoring of wires’ power dissipation. This paper proposed that the lift-off of bond wires will lead to underestimating the thermal resistance measurement, which will overestimate the lifetime of IGBT module and misjudge its state of health.