Pritheesh Gnanaselvam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pritheesh Gnanaselvam has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ameri
Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235
2 shared publications - Jeffrey P. Bons
Aerospace Research Center, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43235
2 shared publications - Robert J. Boyle
Department of Engineering Analysis, N&R Engineering, Parma Heights, OH 44130
2 shared publications - Vinod K. Nagpal
Department of Engineering Analysis, N&R Engineering, Parma Heights, OH 44130
2 shared publications - Ankur H. Parikh
Department of Engineering Analysis, N&R Engineering, Parma Heights, OH 44130
1 shared publication - Ankur H. Parikh1 shared publication
Latest Publications
- Open Access
- 16 July 2021
- Published by ASME International
Design of Stress Constrained SiC/SiC Ceramic Matrix Composite Turbine Blades
While SiC/SiC CMC turbine blades have higher temperature capability than conventional Superalloy turbine blades, cooling CMC blades below their upper use temperature results in smaller strength increases than cooling Superalloy turbine blades. This paper explores the effects on aerodynamic efficiency and stresses for a notional engine where the rpm is held constant and maximum
- 16 July 2021
- Published by ASME International
Open AccessDesign of Stress Constrained SiC/SiC Ceramic Matrix Composite Turbine Blades
While SiC/SiC CMC turbine blades have higher temperature capability than conventional Superalloy turbine blades, cooling CMC blades below their upper use temperature results in smaller strength increases than cooling Superalloy turbine blades. This paper explores the effects on aerodynamic efficiency and stresses for a notional engine where the rpm is held constant and maximum
- Open Access
- 11 March 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (5)
Design of Stress Constrained SiC/SiC Ceramic Matrix Composite Turbine Blades
The structural and aerodynamic performance of a low aspect ratio SiC/SiC ceramic matrix composite (CMC) high pressure turbine (HPT) blade was determined. The application was a NASA notional single aisle aircraft engine to be available in the N + 3, beyond 2030, time frame. The notional rpm was maintained, and to satisfy stress constraints, the annulus area was constrained. This led to a low span blade. For a given clearance, low span blade is likely to have improved efficiency when shrouded. The efficiency improvement due to shrouding was found to strongly depend on the axial gap between the shroud and casing. Axial gap, unlike clearance or reaction, is not a common parameter used to correlate the efficiency improvement due to shrouding. The zero clearance stage efficiency of the low aspect ratio turbine was 0.920. Structural analyses showed that the rotor blade could be shrouded without excessive stresses. The goal was to have blade stresses less than 100 MPa (14.5 ksi) for the unshrouded blade. Under some not very restrictive circumstances, such as blade stacking, a one-dimensional radial stress equation accurately predicted area averaged Von Mises stress at the blade hub. With appropriate stacking, radial and Von Mises stresses were similar.
- 11 March 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (5)
Open AccessDesign of Stress Constrained SiC/SiC Ceramic Matrix Composite Turbine Blades
The structural and aerodynamic performance of a low aspect ratio SiC/SiC ceramic matrix composite (CMC) high pressure turbine (HPT) blade was determined. The application was a NASA notional single aisle aircraft engine to be available in the N + 3, beyond 2030, time frame. The notional rpm was maintained, and to satisfy stress constraints, the annulus area was constrained. This led to a low span blade. For a given clearance, low span blade is likely to have improved efficiency when shrouded. The efficiency improvement due to shrouding was found to strongly depend on the axial gap between the shroud and casing. Axial gap, unlike clearance or reaction, is not a common parameter used to correlate the efficiency improvement due to shrouding. The zero clearance stage efficiency of the low aspect ratio turbine was 0.920. Structural analyses showed that the rotor blade could be shrouded without excessive stresses. The goal was to have blade stresses less than 100 MPa (14.5 ksi) for the unshrouded blade. Under some not very restrictive circumstances, such as blade stacking, a one-dimensional radial stress equation accurately predicted area averaged Von Mises stress at the blade hub. With appropriate stacking, radial and Von Mises stresses were similar.